Question about 1996 GMC Yukon

1 Answer

High speed on blwer

Relaced blower last year because it burnt up.All speeds work except, high speed.Switch is new, and relay is energizing or deenergizing not sure.What to chech next.

Posted by on

  • Anonymous Aug 29, 2008

    2005 Yukon, high speed (5) air will not blow at all, I have to lower the

    fan to 4

  • mlozano May 04, 2009

    Yukon 1996, the blower fan make a very bad noise and work only in high speed, if I turn to lower speed don't work.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a 1996 yukon and i cant get 1 2 or 3 to work on the fan control but 4 does work

Posted on Oct 11, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I find out if the wipers on my 2006 H3 Hummeris on a relay?


The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper micro relay
• Wiper 2 relay
• Wiper diode
• Windshield wiper motor
• Windshield washer pump
• Windshield washer nozzles
• Windshield washer solvent container
• Windshield wiper arm and blade assemblies
• Windshield wiper transmission
• WIP/WASH 10A fuse
• WIPER 25A fuse

Wiper/Washer System Description
The body control module (BCM) controls wiper motor low speed operation. The washer pump and high speed operation are controlled directly by the wiper/washer switch. The windshield wiper/washer switch supplies voltage on the signal circuits to the BCM for windshield wiper/washer operation. When WASH, MIST, DELAY, LOW, or HIGH is detected, the BCM energizes the wiper micro relay by suppling voltage to the relay coil. This allows battery voltage from the WIPER fuse to flow through the relay switched input then through the contacts and out the relay switched output to the wiper 2 relay switch contacts. Since the wiper 2 relay switch contacts are normally closed to the low speed circuit of the windshield wiper motor, the motor will operate at low speed.

Low Speed Operation
When the wiper switch is in the Low position, voltage is supplied through an internal resistor to the signal circuit. The body control module (BCM) monitors the windshield wiper switch signal 1 circuit, and energizes the wiper micro relay which will operate the windshield wiper motor. The wiper motor will operate at low speed, since the wiper 2 relay is de-energized. Low speed can also be commanded with a scan tool, by commanding Wiper Relay Cmd. ON and OFF. Refer to Scan Tool Output Controls .
High Speed Operation
In the High position, the windshield wiper/washer switch supplies voltage to both the wiper micro relay and wiper 2 relay coils. This energizes both relays and allows battery voltage from the wiper micro relay switched output to the switched input of the wiper 2 relay through its contacts and out the switched output of the wiper 2 relay to the high speed circuit of the windshield wiper motor. The windshield wiper motor will operate at high speed. During high speed wiper motor operation the wiper switch signal circuit is at the low speed signal voltage, and the body control module (BCM) supplies redundant voltage to the wiper relay via the wiper diode.

This info is out of hummer factory service manual !

Dec 10, 2016 | 2006 Hummer H3

1 Answer

Engine cold. Start engine reading says engine hot ac off. Fans run all time.


Are the fans running on low or high ?
Circuit/System Description
The engine control module (ECM) commands the fans ON in either high speed or low speed, depending on cooling requirements. In low speed, both fans are turned ON at a reduced speed. High speed has both fans turned ON at full speed.
In low speed operation, the ECM applies ground to the coil side of the fan low relay. This energizes the coil and applies voltage directly to the left cooling fan through the switch side of the fan low relay, which is fed by the fan 1 fuse. The right fan is connected in series to the left fan through the de-energized fan control relay so that both operate at low speed.
In high speed operation, the ECM applies a ground to the coil side of the fan low relay, the fan control relay , and the fan high relay. On the fan high relay, the energized coil closes the switch side of the relay and applies voltage directly to the right cooling fan through the switch side of the relay, which is fed by the fan 2 fuse. At the same time, the ECM energizes fan control relay pulling the switch side over, providing a direct path to ground for the left cooling fan, which has voltage applied through the energized fan low relay. In high speed mode, the fans are operated as a parallel circuit with full voltage applied to each.
You should have it hooked up to a scan tool that can read engine sensor data parameters . Check for DTC'S - diagnostic trouble codes etc...
Circuit/System Verification
  1. If DTCs P0480 or P0481 are set, perform those diagnostics first.
  2. Ignition ON, verify with a scan tool that the control module is not commanding fan activation.
  3. Ignition ON, observe that the fans are not activated.
Your best bet is to take it to a ASE certified repair shop !

Jan 10, 2016 | 2009 Chevrolet Silverado 1500

1 Answer

I'm driving in rain, wipers working good, all of a sudden they quit! I drive for 15 min, check again, they work for a while, then quit again...what in the problem?


If your not familiar with automotive electronics an module control of components , I suggest you take it to the dealer . They have the tools to diagnose this type problem !
The Wiper/Washer System consists of the following components:
?€¢
Windshield wiper/washer switch


?€¢
Body control module (BCM)


?€¢
Wiper PCB relay


?€¢
Wiper high PCB relay


?€¢
Windshield wiper motor


?€¢
Windshield washer fluid pump


?€¢
Windshield washer fluid level switch


?€¢
WPR fuse 25 A


?€¢
WSW fuse 10 A


Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
High Speed Operation When the wiper switch is in the high speed position, ground is applied through the windshield wiper switch high signal circuit to the body control module (BCM) indicating the wiper high speed request. In response to this signal, the BCM then energizes the wiper PCB relay, as stated above, and the wiper high PCB relay by applying ground through the control circuit to the coil side of the relay. With the wiper high relay energized and its switch contacts closed to the high speed control circuit of the wiper motor, the motor will operate at high speed.
Wiper motor high speed operation and the wiper high speed PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
DTC B3715 02: Front Wiper Relay Drive Circuit Short to Ground
DTC B3875 00: Wiper High Speed Relay Circuit
DTC B3922 00: Front Wiper Function Select Circuit
You could Have a switch problem , BCM problem ,PCB relay problem , the pcb relays are non serviceable an the whole under hood fuse box would need to be replaced . Malfunctioning motor bad ground some where etc.....

Dec 20, 2015 | 2008 Chevrolet Impala

1 Answer

1992 chevy C1500: Heat works on low speed, no medium, and high only works intermittantly.


On any other vehicle it sounds like the blower fan switch.
The fan switch provides power or ground to the resistor and there would be a high speed blower relay to bypass the resistor.
But in your case the fan switch is part of the controller.
I don't have a diagram for a 92 but the 94 model shows relays for low medium and high speeds. Each relay gets power from a fuseable link. The high relay gets power thru the low relay if the low relay is not engaged.
If you have the model with 3 relays you may need to check them.

Feb 01, 2013 | 1992 Chevrolet C1500

1 Answer

All the heater blower speeds work on my 1998 Suburban except the high speed. I have replaced the blower motor and the switch. What else could the problem be? I have seen some writings about a resistor but...


Hello Boco.

In your Suburban there is a high blower relay.
When the switch to high is selected it activates a relay to another circuit that is fused separately.
This fuse in under the hood marked blower fuse 3 which is a 50 amp fuse.
This is most likely the problem.
However, if it isn't then the problem becomes the relay, the switch or a broken wire.
If it isn't the fuse, contact me back here using comments and I will help you with the next step in fixing your heater blower.

Thank you for using FixYa.

KL

Jan 21, 2011 | 1998 GMC Suburban

3 Answers

My a/c only works on high. I was told that it was the blower motor resistor not sure where is located.


It's located near the fan motor on the passenger side duct work. It will have a harness plugged into it.
It's mounted with 2 sonic welds, to remove it pry under the mounting points to snap the welds. The replacement resistor is mounted with 2 self tapping screws.

Jul 21, 2010 | 2006 Chevrolet Colorado

2 Answers

Heayer doesn't work


The resistors provide resistance in the circuit, dropping voltage to the blower motor to slow the motor speed down. On high, the blower receives full voltage through the blower relay.

If you had High but no other speeds, then the resistor pack is usually the culprit. If you have all other speeds but high, the most common problem is going to be the blower motor itself, relay, or the switch panel.

You can check this by turning the fan speed to "high", unplug the blower motor, and check to see that you have roughly at least 12v at the plug. If you have 12v, that means the switch panel is activating the relay and the relay is working. Over time, heat kills the magnetic properties of the magnets inside an electrical motor. Without enough magnetic energy, you may not get enough opposing force to spin the rotor full speed when the windings energize, but still enough to spin at lower speeds.

Another thing you can check is the connector at the blower motor and the switch panel. Sometimes these will heat up, start to deform, and cause a bad connection. The bad connection may be able to handle the lower current draw on low speeds, but the higher resistance from the bad connection won't be able to handle the higher current while in the full speed position.

Hope this helps, keep me posted. be glad to help you get your heater working again soon.

Jan 07, 2010 | 1995 Chevrolet Tahoe

1 Answer

I have a 2000 Impala LS my heater resister has blown out 3 times in the last year , also blower work in 1,2,3,4 speeds but not on # 5. what is going on ?


The blower motor is bad. Just because it runs it's drawing too much power some of them are bad when new. 5 speed runs right off the switch and the high relay as they get damaged by the high load of the bad motor too. This is common and it happens alot to cars with over 100thou miles.

Nov 02, 2009 | 2000 Chevrolet Impala

1 Answer

Blower stuck on high speed


yes it will run on high with the resistor unpluged i would have to say your resistor is bad if it does not work at any other speed than high please rate and let me know -jeff

Aug 26, 2008 | 2003 Dodge Grand Caravan AWD

Not finding what you are looking for?
1996 GMC Yukon Logo

Related Topics:

110 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

66616 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...