Question about Chrysler Sebring

1 Answer

Car broken into. Took it to chrysler dealership because, the steering column was broaken and convertible top was cut. Fog light was on the multifunction switch before they replace it with a used one. The switch they replace on my 2003 sebring convertible v6-2.7L VIN T FFV. after I had got it home that night I tried to turn on my fog lights and I keep trying, but could not pull the end of the lever out. I discovered it was not the same lever that was on my car before I took it to the Chrysler Dealership. What should I do?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 126 Answers

Call the manager of the dealership and demand answers tell him your unhappy and tell him you will contact chrysler re this problem if its not rectified . ok good luk

Posted on Jul 19, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Dodge Charger with 136k miles. Horn beeps completely randomly.


There is a short circuit within your steering column and the copper rod that is linked to the horn and the circular strip on steering wheel are now in contact. Remove steering wheel and check there is the spring on the inner part that is either not harnessed well or has broken into pieces and hence the contact.

Jun 22, 2012 | 2006 Dodge Charger

1 Answer

Just replaced the crank sensor on my chrysler cirrus 1996. the factory alarm reset itself. i had previously turned it off. cut the volume wire so lights just blink and makes clinking noise. i can start the...


Thats not a factory alarm that aftermarket. go under the steering column and remove the whole alarm set up. or better yet find a relay that is attach to the starter signal (match the color) and restore how it used to be then you should be able to crank the car , if you sucessfull have bypass the alarm then go ahead and look for its ground and just cut it. The aftermarket cuts into the ignition switch starter signal so that is where you locate the starter relay alarm.

May 22, 2011 | 1996 Chrysler Cirrus

1 Answer

Cuts off while driving


SOUNDS LIKE COIL PACK GETS HOT AND CUTS OUT

Oct 27, 2009 | 2000 Chrysler LHS

1 Answer

When turning the wheel i get a click or a clunk in the steering column!


sounds like a rack and pinion issue or your steering column joint and or bearings are spent. Call a chrysler/dodge dealership, ask for service and see if someone is nice enough to list off some possible causes to your steering column sounds

Oct 06, 2009 | 1996 Jeep Grand Cherokee

2 Answers

Fog lights wont turn off unless the blinker is down...


Disconnect or remove bulbs untill you can get a new switch

Jul 09, 2009 | 2002 Chrysler PT Cruiser

1 Answer

04 Chrysler Sebring looking for pin that connects ignition switch


The reason you need a new steering column, is that part is made into the steering column, and is not servicable by it self. You may be able to find a used one at a salvage yard and transfer some of your parts to it. That would be your cheapest route.

Jun 13, 2009 | 2004 Chrysler Sebring

2 Answers

I just bought a 99 sebring limited and didnt ask how to turn on the fog lights So how do I


On the steering column. There is the yoke to twist to turn on the head lights. Well on that same yoke, underneath the buttom side facing the dash, look for a little lever, or on some a tiny sliter. Tun on the headlights first, then move the lever. This will turn on the fpg lamps. They will not come on without the headlights on.

Mar 28, 2009 | 1999 Chrysler Sebring

9 Answers

2005 Chevy Malibu Electronic Power Steering


I took my car into the dealership on friday 02-13-09 only to find out my steering column needs to be replaced the motor is shorting out for the power steering ~ certain models of malibu's 2005 yr if your vin falls between 5F100001 - 5F250216 call Chevrolet they have a Technical Service Bulletin # 07126 - SPECIAL COVERAGE ADJUSTMENT - LOSS OF POWER STEERING ASSIST - 7 yrs or 70,000 miles regardless of ownership - they will cover the cost of the repair ~ Chevrolet 1-800-630-2438 or
1-800-833-2438 - They saved me from having to pay out of pocket !!!

Aug 18, 2008 | 2005 Chevrolet Malibu

2 Answers

Driving lights on chrysler sebring convertible


The roatating knob that turns on the headlight pulls out to turn on the fog lights, but only pulls out when the headlights are on,

Aug 15, 2008 | 2004 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

90 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...