Question about Chrysler Town & Country

1 Answer

Replacing rear rotor. any trick to break it loose

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Chrysler Master
  • 2,039 Answers

There a hole in the rotor or in the back you have to loosend the emergency brake a justment that what give att that trouble after that big hammer and that it thanks pierre

Posted on Jul 19, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Replaced rear brake calipers on 2003 Sebring. Now caliper does not release off of rotor. Brake line has been bled. Changed caliper out because previous one was not releasing... Any ideas why this is...

Try pumping breaks and let go then break bleeder loose if fluid shoots out it usually means the rubber line is collapsed on the inside and needs replaced

Jun 27, 2011 | 2003 Chrysler Sebring

1 Answer

Everytime I step on the breaks there's always a rattling and grinding sound? What could it be?

It could be pads that wore out and are cutting into the rotors, worn out shoes cutting into the drums, loose hardware occasionally getting stuck in the rear brakes, a dust sheild bent in and rubbing on the rotor.brake pads are worn completely out. have them replaced right away and check for other damage in the caliper, rotors, and make sure that all the little pins and clips are seated properly and not got loose.----------------Thanks.

Dec 08, 2010 | 1993 Honda Accord

1 Answer

Trick to Mini Cooper 2003 rear brake calipers?

Mini cooper rear calipers pistons must be rotated as they are compressed. As you look at the face of the piston, it is rotated clockwise.

Apr 03, 2010 | 2003 Mini Cooper

2 Answers

Cannot get rear rotor off a Dodge Charger 2006. Any Suggestions?

make sure there is no bolts holding it on if that ok then if you are not reusing the rotor hit with a hammer to break it loose. if you plan on reusing the rotor spay it with some penetrating oil then lightly tap on the hub to break it loose. good luck

Aug 01, 2009 | 2006 Dodge Charger

2 Answers

Cannot remove front rotor off of 2001 jeep cherokee it appears all keepers are off but rotor does not want to come off. Is there a trick or is it just realy stuck??

sometimes depending on road conditions where you are at they will get rusted to the hub you can either heat them or just drive them off with a large hammer after all the keepers are off. either way of getting them off will require they be replaced. if they do not need to be replaced right now i would suggest leaving them in place if at all possible because you will ruin the rotors getting them off

May 05, 2009 | 2001 Jeep Grand Cherokee

1 Answer

Remove rear rotor 2004 Chevy Impala

Yes it should, A trick I use when this happens is to beat the lug bolts out, and the rotor will fall off. When you put it all back together use a socket and the lugnut to reseat them.

Apr 25, 2009 | 2004 Honda Accord

2 Answers

Can't get rear rotors off...

there should be two holes in the rotors that will be threaded. send two bolts in them a little at a time to push the rotor away from the backing plate.

Apr 22, 2009 | 2004 Mitsubishi Endeavor

1 Answer

Can you tighten calipers once they are loose?

You need a new caliper as it sounds like that one is sticking. You need to look at the P/B shoes inside the rotors to determine if they need to be replaced, or adjusted.

Mar 16, 2009 | 2000 Ford Crown Victoria

1 Answer

Changing rear rotors

The parking brake shouldn't be holding them on unless you have the brake set. Don't hit them with a hammer or you'll damage the parking brake shoes and springs. Check the cables to make sure they aren't rusted or binding. More likely than not this is the case as the shoes have dug into the rotor. If they are, use a screwdriver to press the shoes off the rotor as you or an assistant slides them off.

Oct 04, 2008 | 2003 Dodge Intrepid

1 Answer

Changing rear rotors

The park brake shoes are on the inside of the rotors, you need to back off the adjustment on the park brake shoes to get the rotors off. They are cable operted and that is were the adjuster is.

Jul 20, 2008 | 2005 Dodge Magnum

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

118 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides