The washer fluid is not spraying and there is no noise at all and the rear wipers stoped working could this be the same problem of my 05 mdx

From the 2013 operators manual;

Push the windshield wiper lever forward to spray washer fluid on the rear window. The lever returns to its starting position when released.

The windshield washer reservoir is used for the windshield and the rear window. Check the fluid level in the reservoir if either washer is not working.

Rear Wiper/Washer System Components
The rear wiper/washer system consists of the following components:
• Rear wiper/washer switch
• Window wiper module-rear
• Window washer pump-rear
• RR WIPER 15A fuse
• RR WPRB 25A fuse
Rear Wiper/Washer System Operation
The rear wiper module controls rear wiper motor operation. Battery voltage supplied to the module is used to operate the wiper motor in all modes and to return the rear wiper arm to the park position after the ignition is turned off. Accessory voltage supplied to the rear wiper/washer switch is used to supply the rear window wiper and washer switch signal circuits. In wiper switch positions 1 and 2 the wiper switch signal circuit voltage level to the wiper motor module determines the wiper motor delay interval. The rear window washer pump supply voltage circuit is used to provide the operating voltage for the rear washer pump for as long as the rear washer switch is pressed. The rear window washer switch signal circuit is used as a wash signal to the rear wiper motor module to operate the wipers during the rear wash operation.


Did you replace the rear wiper module ?

There is a electric motor that pumps washer fluid . Located in the bottom of the washer fluid tank .
Wash Operation (Front and Rear Wipers)
The front and rear washer systems use the same windshield washer fluid pump. When either the front or rear wiper is in the washer position voltage will be supplied to one side of the windshield washer fluid pump (depending on whether it is front or rear), while the other side of the pump is grounded.
At this point, the windshield washer fluid pump sprays solvent onto the windshield. When the front or rear washer is activated, the BCM receives an input from the switch that is activated. The BCM will control the wipers while in the WASH mode. The BCM will control either the front wiper relay or the rear wiper relay to turn on the wipers. The windshield wipers operate at low speed for 3 swipes and returns to the park position.

When turning on the washers do you hear the motor run ? Have some one try it while you listen at the washer fluid tank ! These pump motors do go bad .
turn OFF the ignition.
Disconnect the harness electrical connector of the windshield washer fluid pump.
Connect a test lamp from the windshield washer pump control circuit to a good ground .
Turn ON the ignition, with the engine OFF.
Press the front washer switch.
Does the test lamp illuminate?
YES or NO !

fill the bottle or clean nozzle or replace pump or fuse

Sounds like one of your nozzles is clogged to me. Try this.....Get a spray can of air, like the computer air spray. Stick the long air can nozzle into the spray nozzle. Shoot some air back into the system and see if it frees your clog. When my fluid gets low, mine will get gunk in it and clog to the point of not spraying at all. Compressed air usually does the trick. If not, remove and clean or replace the nozzles.

Check the washer/wiper switch

I have the same problem with my 2000 chevy blazer as skornec had posted. I kinda already figured the hose or spray nozzle was plugged. But the problem with checking those items is that I don't know where the hose is located to the back wiper. And the only thing that could be I see that could be the spray nozzle doesn't even have holes that washer fluid could spray from. So basically I just would LOVE if someone could please inform this lame brain of where to find the spray nozzle on the rear window and where in the interior of my blazer does the washer hose run.

if your vue is a newer model it is common for the washer hose to get pinched by the cowl when the hood is shut. This in turn can puncture the hose, which is easily replaceable. if that is not the problem you may have a bad washer pump.

there are two motors ,one runs the front and the other runs the rear. check the connection at the front washer pump sometimes it gets dirty and doesnt make a good connection, if the connection is good and clean then replace the washer pump, here a picture of it. hope this helps

check hose for clogs if it's ok then you need to check the reservoir motor