Question about 1999 Oldsmobile Cutlass

1 Answer

1999 olds cutlass glove box removal

How do I remove the glove box in a 1999 Oldsmobile Cutlass as the handle is broken?

Posted by on

  • Anonymous Mar 29, 2014

    WHEN ACELERATING LOUND WHING NOISE OCCURS

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 56 Answers

You need to remove all the screws on the bottom of the glove box on the outside, then on the inside remove all the screws too. and then pull it out. sometimes some glove boxes have stoppers on the edge of the door inside and you have to pry on them to pull the stoppers in front of the side of the glove box so you can remove it entirely from the dash.

Posted on Oct 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace the glove box latch on a 1998 Oldsmobile Cutlass GLS?


Most will have a row of screws just across the bottom of the door, either on the outside(look up from the floor) or a row of screws inside the door. Open the glove box and look at very bottom edge.

Aug 05, 2014 | 1998 Oldsmobile Cutlass

1 Answer

How do I remove glove box on 1997 olds cutlass supreme


check the fusebox under your hood for the horn relay,should be a black box close to your battery that has fuses in it

Jan 31, 2013 | 1997 Oldsmobile Cutlass Supreme

1 Answer

99 olds cutlass blower motor resistor


remove glove box to get better access to the blower motor. resistor is located beside the blower fan motor. with glove box removed, then you will not have to stand on your head doing the job, good-day!

Jan 29, 2012 | 1999 Oldsmobile Cutlass

1 Answer

Blower motor sounds like it is going to stop. how hard is it to replace?


here are the instructions for fan blower removal. remove lower right dash insulator panel from under glove box. slide the body control module aside for access to the blower motor.( bcm ). remove the 3 screws that hold it in. pull the blower motor and fan straight down and dis connect electrical connector. if replacing blower motor, remove fan to put on new motor. 99 olds cutlass, have a good day !! just take your time and it is not that hard.

Jan 22, 2011 | 1999 Oldsmobile Cutlass

1 Answer

Trying to find the engine control module for 1991 olds cutlass siera sl


The ECM is located right behind the glove box. First remove the negative (-) battery cable. Then remove the front of your glove box, just a few small screws. The interior of the glove box is cardboard and will pull out after removal of screws. Then unplug the 3 electrical plugs and let them hang out of the way. Now, remove the bolts on the side of the bracket holding the ECM IN.

Nov 17, 2010 | 1991 Oldsmobile Cutlass Ciera

2 Answers

How to replace a blower motor on a 99 oldsmobile cutlass


remove lower right dash insulator panal from beneath glove box. slide bcm aside to get to blower. remove the three screws holding the blower motor, pull blower and fan straight out. remove fan from old blower if replacing with a new motor. good-luck!!

Jul 17, 2010 | 1999 Oldsmobile Cutlass

1 Answer

'94 Olds Cutlass Supreme Door Handles


You have to find the linkage and pull it. If yu cannot find the linkage, one trick is to go to a self serve wrecking yard and play with one of the 90s olds by removing the door panel and looking at it to see how it works.

Apr 05, 2010 | 1994 Oldsmobile Cutlass Supreme

2 Answers

Where is a prom chip located at on a oldsmobile


Then programmable read only memory (PROM) chip that you are asking about is located inside the electronic control module.
This module is located just above the glove compartment in the dash area.
Removal of the glove compartment is required to remove this module. After removing the ECM you will note a small access cover. Remove this cover and you are at the PROM.
Good luck, it is quite easy.

Mar 10, 2010 | 1992 Oldsmobile Cutlass Ciera

1 Answer

Replacing 1999 oldsmobile cutlass headlight bulb


remove the pins and the plastic shield over the headlight housing.pull straight up on the 2 clips to release housing from ball studs , twist and withdraw the bulbs from housing!! do not touch bulbs, oil from skin will make them blow out quicker, if need be use a pair of clean gloves to be safe, installation the reverse of removal!!!

Jun 03, 2009 | 1999 Oldsmobile Cutlass

1 Answer

1999 Oldsmobile Cutlass Cigarette Lighter Fuse


Under the hood directly in front of the driver is a covered fuse block. Remove the cover and the fuse is #34.

Jan 28, 2009 | 1999 Oldsmobile Cutlass

Not finding what you are looking for?
1999 Oldsmobile Cutlass Logo

330 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...