Question about 1995 Mazda MPV

1 Answer

Engine won't start. suddenly stopped while in motion

It's got spark, to the plugs, wondering if low fuel pump pressure could cause it not to run and up and quit.

Posted by on

  • WDEMON Dec 02, 2008

    same

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Yes it could but it would have to be pretty low to not run at all.

Posted on Dec 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Car stopped running while driving


run the fault codes and check for cam/crank position sensor . check that the cam shaft is turning (broken cam belt)

Jan 17, 2014 | Volkswagen GTI Cars & Trucks

1 Answer

2003 kia Sedona won't. start


If this is a sudden occurrence and nothing suspicious happened prior, you most likely lost either gas or spark to the engine. You need to check for both.

Do you hear the fuel pump in the gas tank buzz on for a couple of seconds when you turn the ignition key to ON? Unless the fuel pump turns on and puts gas under high pressure at the fuel injectors, the engine cylinders won't get gas to start. Correct fuel pressure is crucial to know if you have a fuel pump (or fuel filter) problem. If the pressure is correct, it is probably not a fuel problem but a spark problem, although there are less common instances where a fuel injector circuit may malfunction.

The ignition system not producing spark at the spark plugs is the other common problem of no starts. Buy a cheap spark tester at a parts store, plug it into one of your spark plug wires, then crank the engine over and watch for a strong blue spark. You might need a helper to do this. If you see a consistent spark, the ignition system is probably good, although you should probably check more than just one plug wire-sometimes one bad ignition coil in a coil pack will cause no starting. Good luck.

Jan 28, 2012 | 2003 Kia Sedona

1 Answer

Not getting fire over the #1 spark plug coil. What needs to be changed/what is the cause of the problem? The engine stopped running while in motion. Battery light came on first then all the other warning...


  1. Check fuel level in fuel tank, add fuel if empty.
  2. Check battery condition and state of charge. If voltage and load test below specification, charge or replace battery.
  3. Check battery terminal and cable condition and tightness. Clean terminals and replace damaged, worn or corroded cables.
  4. Check fuel delivery system. If fuel is not reaching the fuel injectors, check for a loose electrical connector or defective fuse, relay or fuel pump and replace as necessary.
  5. Engine may have excessive wear or mechanical damage such as low cylinder cranking pressure, a broken camshaft drive system, insufficient valve clearance or bent valves.
  6. Check for fuel contamination such as water in the fuel. During winter months, the water may freeze and cause a fuel restriction. Adding a fuel additive may help, however the fuel system may require draining and purging with fresh fuel.
  7. Check for ignition system failure. Check for loose or shorted wires or damaged ignition system components. Check the spark plugs for excessive wear or incorrect electrode gap. If the problem is worse in wet weather, check for shorts between the spark plugs and the ignition coils.
  8. Check the engine management system for a failed sensor or control module.

May 21, 2011 | 2000 Mitsubishi Galant

2 Answers

2000 Eclipse GT turns over but doesn't start. Fires once in a while but won't run. Had timing belt replaced.


Hi, if the car turn over, and it don't start. Then it is like the engine don't get fuel. Or bad a spark plugs. Most common problem is the fuel pump going bad.

It could also be a bad fuse, but a easy way to check if the fuel pump is ok is to have someone stand at the back of the car when you turn the ignition. The fuel pump should make a buzzing sound for a few seconds. And if you don't start the car right away the fuel pump will stop.

If you don't hear any buzzing from the fuel pump/fuel tank then you have a bad fuel pump............

May 11, 2011 | Mitsubishi Eclipse Cars & Trucks

1 Answer

I have A chevy silverado and it is hard to get it to turn over. when it finally does turn over the truck runs fine.


Engine cranks normally, but it does not fire:
You turn the key to start and hear the starter motor crank the engine, but when you release the key, the cranking stops and there is silence. This means that the battery and starting motor are working properly, but the engine is not firing. If you continue cranking the engine over in this way, the battery will eventually run down and will need to be recharged, but the battery and starter are not the cause of your problem.
There are a number of causes for this type of no-start condition, the most common being that you are simply out of gas. Assuming that you have fuel in the tank, you will need to go through a series of tests to determine what is causing the problem. The testing procedure is as follows:---

Spark:---------An easy way to test for spark is with an inexpensive spark tester. This is a device that is readily available at most auto supply stores. You use it by simply holding it next to a spark plug wire. If you see the neon lamp flashing while someone cranks the engine, then you have spark and should move on to checking for fuel. If there is no spark, or a very weak spark, you will have to replace the spark plug or the coil pack.It has to be checked.

Fuel:
First step here is to listen for the fuel pump running inside the gas tank. When you turn the key to run, you should easily hear the pump come on, run for a few seconds to build fuel pressure, then turn off. If you do not hear it, it could mean that the fuel pump or circuitry is bad. (Fuel pump failure is a common problem).

Fuel injected cars are very sensitive to proper fuel pressure. If the pressure is off, even by a few pounds, it will cause noticeable performance problems, or a no-start condition. To check for proper fuel pressure, you will need a fuel pressure gauge that is suitable for your type of system. Or you can also get the fuel pressure tested at local car garage, If fuel pressure is low then its a fuel pump and fuel filter related problem.

Compression:

If you know that you have spark and fuel, the next step is to check for compression. For this, you will need a mechanic's grade compression tester that will screw into a spark plug hole. You will need to remove the spark plugs and use the compression tester to test the compression on each cylinder. If the compression is very low on all cylinders, that is a sure sign that the timing belt (or timing chain depending on the engine) has failed and will have to be replaced.

-------------

This troubleshooting will let you know the problem.Thanks.

Mar 01, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

Turns over but won't start


You turn the key to start and hear the starter motor crank the engine, but when you release the key, the cranking stops and there is silence. This means that the battery and starting motor are working properly, but the engine is not firing. If you continue cranking the engine over in this way, the battery will eventually run down and will need to be recharged, but the battery and starter are not the cause of your problem.
There are a number of causes for this type of no-start condition, the most common being that you are simply out of gas. Assuming that you have fuel in the tank, you will need to go through a series of tests to determine what is causing the problem. The testing procedure is as follows:---

Spark:---------An easy way to test for spark is with an inexpensive spark tester. This is a device that is readily available at most auto supply stores. You use it by simply holding it next to a spark plug wire. If you see the neon lamp flashing while someone cranks the engine, then you have spark and should move on to checking for fuel. If there is no spark, or a very weak spark, you will have to replace the spark plug or the coil pack.It has to be checked.

Fuel:
First step here is to listen for the fuel pump running inside the gas tank. When you turn the key to run, you should easily hear the pump come on, run for a few seconds to build fuel pressure, then turn off. If you do not hear it, it could mean that the fuel pump or circuitry is bad. (Fuel pump failure is a common problem).

Fuel injected cars are very sensitive to proper fuel pressure. If the pressure is off, even by a few pounds, it will cause noticeable performance problems, or a no-start condition. To check for proper fuel pressure, you will need a fuel pressure gauge that is suitable for your type of system. Or you can also get the fuel pressure tested at local car garage, If fuel pressure is low then its a fuel pump and fuel filter related problem.

Compression:

If you know that you have spark and fuel, the next step is to check for compression. For this, you will need a mechanic's grade compression tester that will screw into a spark plug hole. You will need to remove the spark plugs and use the compression tester to test the compression on each cylinder. If the compression is very low on all cylinders, that is a sure sign that the timing belt (or timing chain depending on the engine) has failed and will have to be replaced.

-------------
This troubleshooting will let you know the problem.Thanks.

Jan 24, 2011 | 1990 Ford F150

1 Answer

Car cranks but will not start.


You turn the key to start and hear the starter motor crank the engine, but when you release the key, the cranking stops and there is silence. This means that the battery and starting motor are working properly, but the engine is not firing. If you continue cranking the engine over in this way, the battery will eventually run down and will need to be recharged, but the battery and starter are not the cause of your problem.
There are a number of causes for this type of no-start condition, the most common being that you are simply out of gas. Assuming that you have fuel in the tank, you will need to go through a series of tests to determine what is causing the problem. The testing procedure is as follows:---

Spark:---------An easy way to test for spark is with an inexpensive spark tester. This is a device that is readily available at most auto supply stores. You use it by simply holding it next to a spark plug wire. If you see the neon lamp flashing while someone cranks the engine, then you have spark and should move on to checking for fuel. If there is no spark, or a very weak spark, you will have to replace the spark plug or the coil pack.It has to be checked.

Fuel:
First step here is to listen for the fuel pump running inside the gas tank. When you turn the key to run, you should easily hear the pump come on, run for a few seconds to build fuel pressure, then turn off. If you do not hear it, it could mean that the fuel pump or circuitry is bad. (Fuel pump failure is a common problem).

Fuel injected cars are very sensitive to proper fuel pressure. If the pressure is off, even by a few pounds, it will cause noticeable performance problems, or a no-start condition. To check for proper fuel pressure, you will need a fuel pressure gauge that is suitable for your type of system. Or you can also get the fuel pressure tested at local car garage, If fuel pressure is low then its a fuel pump and fuel filter related problem.

Compression:

If you know that you have spark and fuel, the next step is to check for compression. For this, you will need a mechanic's grade compression tester that will screw into a spark plug hole. You will need to remove the spark plugs and use the compression tester to test the compression on each cylinder. If the compression is very low on all cylinders, that is a sure sign that the timing belt (or timing chain depending on the engine) has failed and will have to be replaced.

-------------
This troubleshooting will let you know the problem.Thanks.

Jan 20, 2011 | 2004 Hyundai Santa Fe

1 Answer

My car cranks but i will not start at times. What could be the problem?


You turn the key to start and hear the starter motor crank the engine, but when you release the key, the cranking stops and there is silence. This means that the battery and starting motor are working properly, but the engine is not firing. If you continue cranking the engine over in this way, the battery will eventually run down and will need to be recharged, but the battery and starter are not the cause of your problem.
There are a number of causes for this type of no-start condition, the most common being that you are simply out of gas. Assuming that you have fuel in the tank, you will need to go through a series of tests to determine what is causing the problem. The testing procedure is as follows:---

Spark:---------An easy way to test for spark is with an inexpensive spark tester. This is a device that is readily available at most auto supply stores. You use it by simply holding it next to a spark plug wire. If you see the neon lamp flashing while someone cranks the engine, then you have spark and should move on to checking for fuel. If there is no spark, or a very weak spark, you will have to replace the spark plug or the coil pack.It has to be checked.

Fuel:
First step here is to listen for the fuel pump running inside the gas tank. When you turn the key to run, you should easily hear the pump come on, run for a few seconds to build fuel pressure, then turn off. If you do not hear it, it could mean that the fuel pump or circuitry is bad. (Fuel pump failure is a common problem).

Fuel injected cars are very sensitive to proper fuel pressure. If the pressure is off, even by a few pounds, it will cause noticeable performance problems, or a no-start condition. To check for proper fuel pressure, you will need a fuel pressure gauge that is suitable for your type of system. Or you can also get the fuel pressure tested at local car garage, If fuel pressure is low then its a fuel pump and fuel filter related problem.

Compression:

If you know that you have spark and fuel, the next step is to check for compression. For this, you will need a mechanic's grade compression tester that will screw into a spark plug hole. You will need to remove the spark plugs and use the compression tester to test the compression on each cylinder. If the compression is very low on all cylinders, that is a sure sign that the timing belt (or timing chain depending on the engine) has failed and will have to be replaced.

-------------
This troubleshooting will let you know the problem.Thanks.

Jan 19, 2011 | 1997 Saab 900

1 Answer

1995 Mazda MX 6 2.5.\r\nReplaced head . All timing marks are on the dots, but still will not start. It kranks up, but won't start.


Engine cranks normally, but it does not fire:
You turn the key to start and hear the starter motor crank the engine, but when you release the key, the cranking stops and there is silence. This means that the battery and starting motor are working properly, but the engine is not firing. If you continue cranking the engine over in this way, the battery will eventually run down and will need to be recharged, but the battery and starter are not the cause of your problem.
There are a number of causes for this type of no-start condition, the most common being that you are simply out of gas. Assuming that you have fuel in the tank, you will need to go through a series of tests to determine what is causing the problem. The testing procedure is as follows:---
Spark:---------An easy way to test for spark is with an inexpensive spark tester. This is a device that is readily available at most auto supply stores. You use it by simply holding it next to a spark plug wire. If you see the neon lamp flashing while someone cranks the engine, then you have spark and should move on to checking for fuel. If there is no spark, or a very weak spark, you will have to replace the spark plug or the coil pack.It has to be checked. Fuel:
First step here is to listen for the fuel pump running inside the gas tank. When you turn the key to run, you should easily hear the pump come on, run for a few seconds to build fuel pressure, then turn off. If you do not hear it, it could mean that the fuel pump or circuitry is bad. (Fuel pump failure is a common problem).
Fuel injected cars are very sensitive to proper fuel pressure. If the pressure is off, even by a few pounds, it will cause noticeable performance problems, or a no-start condition. To check for proper fuel pressure, you will need a fuel pressure gauge that is suitable for your type of system.Or you can also get the fuel pressure tested at local car garage,If fuel pressure is low then its a fuel pump and fuel filter related problem. Compression:

If you know that you have spark and fuel, the next step is to check for compression. For this, you will need a mechanic's grade compression tester that will screw into a spark plug hole. You will need to remove the spark plugs and use the compression tester to test the compression on each cylinder. If the compression is very low on all cylinders, that is a sure sign that the timing belt (or timing chain depending on the engine) has failed and will have to be replaced.

-------------

This troubleshooting will let you know the problem.Thanks.


Dec 08, 2010 | 1995 Mazda MX-6

Not finding what you are looking for?
1995 Mazda MPV Logo

Related Topics:

128 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...