Question about 2004 Nissan Murano

1 Answer

We are working on our rear brakes and can't find our repair manual, what is the required torque for the caliper?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Nissan Master
  • 705 Answers

Tight. I use my Snap On air ratchet which puts out about 90 pound of tourque and I naver had a problem.

Posted on Jul 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the torque specifications on the rear caliper bolts on a 2002 Lincoln Ls v8 3.9 ??


Hi Joel me again,you posted your Lincoln,guess what,I have a 2004 Lincoln LS with the 3.0 engine,drives good,here's a link on your back brakes... Repair Guides Rear Disc Brakes Brake Caliper AutoZone com

Jul 27, 2015 | Lincoln Cars & Trucks

2 Answers

Rear pad removal?


Here ya go! This is for the rear brake pads removal:

Removal & Installation
  1. Remove the brake master cylinder filler cap. Check brake fluid level in brake master cylinder reservoir. Remove fluid until brake master cylinder reservoir is half full.
  2. Raise and support the vehicle.
  3. Remove the wheel and tire assembly.
  4. Inspect the brake pads for wear or contamination. If worn, damaged or past specification, install new components.
  5. Remove the caliper pin bolts.
  6. Remove the rear disc brake caliper.
  7. Remove the brake pads and rail clips.
  8. Inspect the disc brake caliper for leaks. If leaks are found, disassembly is required.
  9. Installation is the reverse of removal. Observe the following torques:
    • Caliper bolts: 27 ft. lbs. (36 Nm)
  10. // // 0) preLoad.src = ctl00_cphLeft_chRepairTreeNav_tvTOC_ImageArray[i]; } ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.lastIndex = 30; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.populateLog = theForm.elements['ctl00_cphLeft_chRepairTreeNav_tvTOC_PopulateLog']; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.treeViewID = 'ctl00$cphLeft$chRepairTreeNav$tvTOC'; ctl00_cphLeft_chRepairTreeNav_tvTOC_Data.name = 'ctl00_cphLeft_chRepairTreeNav_tvTOC_Data'; //]]>

May 12, 2011 | 2002 Ford E350

2 Answers

How to change brake pad and check rotors


Brake Pads Removal & Installation Front for_car_toy_cam_02-04_sst_frt_dsc_asm.gif

To Remove:
  1. Drain brake fluid to ½ full level in reservoir.
  2. Remove the front wheels. toy_car_cam_frontbrakepads.gif

  3. Remove the front brake caliper assembly.
  4. Remove the 2 anti-squeal shims from each of the 2 brake pads.
  5. Remove the wear indicator from each of the 2 brake pads.
To Install:
NOTE: When replacing worn pads, the anti-squeal shims must be replaced together with the pads.
toy_car_cam_frontbrakepads.gif

  1. Using a large C clamp or equivalent press piston into the caliper.
  2. Apply disc brake grease to the inside of each anti-squeal shim.
  3. Install the anti-squeal shims on each pad.
  4. Install the pad wear indicator clip to the pads.
  5. Install the pads with the pad wear indicator plate facing upward.
  6. Install the brake caliper with the 2 mounting bolts. Torque the bolts 25 ft-lb (34 Nm).
  7. Install the front wheels.
  8. Fill the master cylinder with new clean brake fluid.
  9. Pump the brake pedal several times to seat the brake pads.
Rear TMC made rear brake components toy_car_cam_tmcrearbrakes.gif

TMMK made rear brake components toy_car_cam_tmmkrearbrakes.gif

To Remove:
  1. Drain the brake fluid to ½ full level in reservoir.
  2. Remove the rear wheels.
  3. Remove the caliper slide pins.
  4. Remove the caliper slide pin bushings (TMMK made) (Kentucky).
  5. Remove the rear brake calipers.
  6. Remove the 2 brake pads with the anti-squeal shims.
  7. Remove the anti-squeal shims and pad wear indicators from brake pads.
To Install:
  1. Using a large C clamp or equivalent press the piston into the caliper.
  2. Coat both sides of the outer anti-squeal shim with pad grease.
  3. Install anti-squeal shims to each pad.
  4. Install wear indicators on the 2 brake pads.
  5. Install the caliper slide pin bushings (TMMK made) (Kentucky).
  6. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 34 ft-lb (47 Nm)
  7. Fill the master cylinder with new clean brake fluid.
  8. Pump the brake pedal several times to seat the brake pads.
  9. Install the rear wheels.
prev.gif next.gif Brake Rotor Removal & Installation Front To Remove:
  1. Remove the front wheels.
  2. Remove the front brake caliper assembly.
  3. Remove the front brake pads.
  4. Remove the 2 bolts and caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the front wheel disc.
To Install:
  1. Align the match marks and install the front disc.
  2. Install the brake caliper mounting bracket. Torque the bolts 79 ft-lb (107 Nm).
  3. Install the brake caliper. Torque the bolts 25 ft-lb (34 Nm).
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the front wheel.
Rear To Remove:
  1. Remove the rear wheels.
  2. Remove the brake caliper assembly.
  3. Remove the brake pads.
  4. Remove the 2 bolts and the caliper mounting bracket.
  5. Place match marks on the disc and axle hub.
  6. Remove the rear disc.
To Install:
  1. Align the match marks and install the rear disc.
  2. Install the rear brake caliper mounting bracket. Torque the bracket bolts as follows:
    • TMC made (Japan): Torque the bracket bolt 46 ft-lb (61.8 Nm)
    • TMMK made (Kentucky): Torque the bracket bolt 34 ft-lb (47 Nm)
  3. Install the rear brake caliper with the slide pins. Torque the slide pins as follows:
    • TMC made (Japan): Torque the caliper slide pin 25 ft-lb (34.3 Nm)
    • TMMK made (Kentucky): Torque the caliper slide pin 32 ft-lb (43 Nm)
  4. Install new gaskets and connect the brake hose to the caliper with the banjo fitting bolt. Torque the fitting bolt 22 ft-lb (29.4 Nm).
  5. Fill the reservoir with brake fluid.
  6. Bleed the brake system.
  7. Install the rear wheel
prev.gif next.gif

Jan 25, 2011 | 2007 Toyota Camry

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

1 Answer

Change rear brake discs


  1. here is some instuctions on how to do the brake pad replacement this should help you out
  2. Jack up the vehicle on a secure metal part of the vehicle and place jack stands in the same area.
  3. 2 Lower the jack until the weight of the car is solely on the jack stands.
  4. 3 Loosen the lug nuts and remove the wheel from the vehicle, exposing the brake system.
  5. 4 Loosen the caliper slide pins from the rear of the caliper and slide the caliper pins out of the caliper.
  6. 5 Remove the caliper from the brake system and remove the old brake pads.
  7. 6 Secure the caliper to a part of the suspension with a bungee cord to avoid it hanging by the rubber brake hos, where it could be damaged or start leaking.
  8. 7 Loosen the two bolts that hold the caliper bracket to the vehicle and remove the caliper bracket.
  9. 8 Pull the rotor from the vehicle.
  10. 9 Measure the thickness of the rotor with the micrometer. Compare the measurement to the "minimum thickness" stamp on the rotor or the manufacturer specifications in the repair manual.
  11. 10 Take the rotors to a machine shop to have them resurfaced if they are above specification and need resurfacing. Verify the manufacturer's recommendations in the repair manual, as rotors do not always need to be resurfaced or replaced.
  12. 11 Reinstall the rotor on the vehicle.
  13. 12 Place the caliper bracket back on the vehicle and hand tighten the bolts on the back of it.
  14. 13 Torque the bracket bolts down to the manufacturer specifications in the repair manual.
  15. 14 Place a new hardware kit in the caliper bracket and set the pads in the hardware.
  16. 15 Press in the caliper piston with the caliper piston tool to allow the caliper to fit over the new brake pads.
  17. 16 Slide the caliper over the brake pads and reinstall the caliper slide pins.
  18. 17 Torque the caliper slide pins to the manufacturer's specifications.
  19. 18 Replace the wheel on the vehicle and torque it down to manufacturer specifications located in your repair manual.
  20. 19 Lift the vehicle off of the jack stand with the floor jack and remove the jack stands.
  21. 20 Lower the vehicle to the ground and remove the floor jack.
  22. 21 Press the brake pedal several times to pressurize the brake system before test driving the vehicle.
  23. 22 Drive the vehicle, performing several hard stops to make certain the brakes are operating properly.
jQuery('.article ol .image').each(function(i,e){ var $this = jQuery(this); $this.find('img').error(function(){ jQuery(this).remove(); $this.remove(); }); });

Aug 29, 2010 | 2001 Toyota Celica

1 Answer

Torque for pyutting new rear brakes and rotors on a 2006 Town&Cou


Caliper mounting bracket bolts 125 ft, Caliper guide pins/bolts 26 ft, Brake hose to caliper 35 ft. Wheel lug nuts 100 ft. Wheel speed sensor 115in lbs*** This is for disc rear brakes Teves system. You do know that the rear disc is a Rotor/Drum. The parking brake shoes ride on the inside.

Jan 22, 2010 | 2006 Chrysler Town & Country

2 Answers

Brake job torque spec


Caliper bolt 25 ft lbs/ caliper bracket bolt 79.6 ft lbs

Nov 13, 2009 | 2005 Honda Civic

1 Answer

Rear brake rotor replacment


206-04: Rear Disc Brake 2000 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Disc Removal
  1. NOTE: When removing the rear brake disc (2C026) in this procedure it is not necessary to disconnect the hydraulic lines.
    Remove the rear disc brake caliper (2552). For additional information, refer to Caliper in this section.
  2. Disconnect the brake hose.
  3. Remove bolt.
  4. Disconnect the rear wheel brake hose (2A442).
  5. Remove the copper washers and plug the brake hose.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not remove the guide pins or guide pin boots unless a problem is suspected. The guide pins are meant to be sealed for life and are not repairable. Use Silicone Brake Caliper Grease and Dielectric Compound D7AZ-19A331-A (Motorcraft WA-10) or an equivalent silicone compound meeting Ford specification ESE-M1C171-A for re-lubing the caliper slide pins. Other greases can swell the guide pin boots, resulting in contamination and accelerated corrosion or wear of the caliper slide pin mechanism.
    Remove the rear disc brake caliper (2552).
    1. Remove the brake caliper bolts (2W303).
    1. Lift the rear disc brake caliper off the rear disc brake caliper anchor plate (2C220).
  1. Inspect the rear disc brake caliper for leaks.
    • If leaks are found, disassembly is required. Refer to Caliper in this section.
  1. NOTE: If the rear brake disc binds on the rear parking brake shoe and linings, remove the adjustment hole access plug and contract the parking brake shoe and lining.
    Remove the rear brake disc.
  1. syn~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Use a hub-mount brake lathe if necessary to machine the rear brake disc.
    Measure the rear brake disc, and resurface as necessary. Install a new rear brake disc if beyond specification.

Mar 28, 2009 | 2000 Ford Explorer

1 Answer

How do i take off the disc brakes on my 2001 toyota celica?


These instructions came from Auto Zone's website and their free, online repair guides. Just plug in your make, model and year and you can get exact instructions and pictures for your repair. Sweeeeeeet! Good Luck!
  1. Loosen the wheel lug nuts slightly.
  2. Raise and support the vehicle safely.
  3. Remove the wheels.
  4. Disconnect the brake hose from the caliper. Plug the end of the hose to prevent loss of fluid. Some brake lines have a union bolt and gasket type line attached to the caliper. Do NOT lose the washers.
0900c152801a856d.jpgRemove the brake hose union bolt with gaskets from the caliperHave a container handy to catch brake fluid from the disconnected lines.
  1. Hold the sliding pin and remove the bolts that attach the caliper to the torque plate.
0900c152801a856e.jpgRemove the two bolts that attach the caliper to the backing plate
  1. With two hands, lift up and remove the caliper assembly.
To install:
  1. Grease the caliper pins and bolts with Lithium grease or equivalent. Temporarily install the caliper on the torque plate with the installation bolts.
0900c152801a856f.jpgThe sliding pins should be greased with Lithium-based grease before installation
  1. Hold the sliding pin and tighten the installation bolts to 25 ft. lbs. (34 Nm) on the front wheels, and 14 ft. lbs. (20 Nm) in the rear.
  2. Attach the flexible brake hose to the caliper with new gaskets. Tighten the hose to 22 ft. lbs. (30 Nm).
Install the brake hose lock securely in the lock hole, in the caliper.
  1. Fill and bleed the system.
  2. Install the wheel, lower the vehicle and tighten the lug nuts.
  3. Before moving the vehicle, make sure to pump the brake pedal to seat the pads against the rotors.
  4. Check for leaks.
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove the wheels.
  3. Disconnect the brake hose from the caliper.
  4. Remove the bolts that attach the caliper to the torque plate. If applicable, hold the flats of the sliding pin with a wrench while loosening the caliper attaching bolts.
  5. Lift up and remove the caliper assembly.
To install:
  1. Install the caliper and loosely install the bolts.
  2. Hold the flats of the sliding pin with a wrench, then tighten the bolts. Tighten to 25 ft. lbs. (34 Nm) except on Celica rear calipers. Tighten the bolts on Celica rear calipers to 34 ft. lbs. (47 Nm).
  3. Connect the brake hose to the caliper, using 2 new washers.
  4. Fill the brake system to the proper level and bleed the brake system.
  5. Add brake fluid to the reservoir to fill to the correct level.
  6. Lower the vehicle to the ground.

Jul 17, 2008 | Toyota Celica Cars & Trucks

Not finding what you are looking for?
2004 Nissan Murano Logo

Related Topics:

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...