Question about 2005 Dodge Ram 3500

1 Answer

Adjustable Pedals I have adjustable pedals and a piece of black plastic fell out where the brake pedal telescopes and now there is side to side play in the brake pedal. How can I fix it

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 393 Answers

Put plastic back

Posted on Nov 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 windstar anti-theft no crank


Power-adjustable pedals are new options on Ford's Windstar. The accelerator and brake pedals adjust within a four-inch range.

if you need an OBDII Code Scanner, click here: OBDII Code Scanner

Oct 30, 2012 | Ford Cars & Trucks

1 Answer

Heater core 2004 chrysler pacifica replace


  1. Remove the silencer boot fasteners located around the base of the lower steering shaft from the dash panel so that it may be pushed aside.
  2. Remove the brake lamp switch from its mounting bracket.
  3. Disconnect the power brake booster input rod (push rod) from the pin on the brake pedal arm.
  4. If equipped with power adjustable pedals, remove the adjustable pedal assembly.
Note: Take the proper precautions to protect the carpeting below the heater core from spilled engine coolant and have absorbent toweling readily available to clean up any spills.

  1. Remove the heater core tubes.
  2. Remove the two screws that secure the heater core mounting plate to the HVAC air distribution
    1. If NOT equipped with power adjustable pedals, pull the accelerator pedal upward and push the brake pedal downward for clearance to remove the heater core from the air distribution housing.
    2. Remove the heater core by carefully pulling it straight out of the side of the air distribution housing.
    Installation

    1. If NOT equipped with power adjustable pedals, pull the accelerator pedal upward and push the brake pedal downward for clearance to install the heater core into the HVAC air distribution housing.
    2. Install the heater core by carefully pushing it straight into the side of the air distribution housing.
    3. Install the two screws that secure the heater core to the air distribution housing. Tighten the screws to 2 Nm ( 17 in lbs ) .
    4. Install the heater core tubes.
    5. If equipped with power adjustable pedals, install the adjustable pedal assembly.
    6. Connect the power brake booster input rod to the pin on the brake pedal arm.
    7. Install a new brake lamp switch.
    8. Install the silencer boot around the base of the lower steering shaft on the dash panel.
    9. Reconnect the negative battery cable.
    10. If the heater core is being replaced, flush the cooling system.
    11. Refill the engine cooling system.
    housing.

Nov 01, 2011 | 2004 Chrysler Pacifica

1 Answer

Replacing heater core chryler picifica


  1. Remove the silencer boot fasteners located around the base of the lower steering shaft from the dash panel so that it may be pushed aside.
  2. Remove the brake lamp switch from its mounting bracket.
  3. Disconnect the power brake booster input rod (push rod) from the pin on the brake pedal arm.
  4. If equipped with power adjustable pedals, remove the adjustable pedal assembly.
Note: Take the proper precautions to protect the carpeting below the heater core from spilled engine coolant and have absorbent toweling readily available to clean up any spills.

  1. Remove the heater core tubes.
  2. Remove the two screws that secure the heater core mounting plate to the HVAC air distribution
    1. If NOT equipped with power adjustable pedals, pull the accelerator pedal upward and push the brake pedal downward for clearance to remove the heater core from the air distribution housing.
    2. Remove the heater core by carefully pulling it straight out of the side of the air distribution housing.
    Installation

    1. If NOT equipped with power adjustable pedals, pull the accelerator pedal upward and push the brake pedal downward for clearance to install the heater core into the HVAC air distribution housing.
    2. Install the heater core by carefully pushing it straight into the side of the air distribution housing.
    3. Install the two screws that secure the heater core to the air distribution housing. Tighten the screws to 2 Nm ( 17 in lbs ) .
    4. Install the heater core tubes.
    5. If equipped with power adjustable pedals, install the adjustable pedal assembly.
    6. Connect the power brake booster input rod to the pin on the brake pedal arm.
    7. Install a new brake lamp switch.
    8. Install the silencer boot around the base of the lower steering shaft on the dash panel.
    9. Reconnect the negative battery cable.
    10. If the heater core is being replaced, flush the cooling system.
    11. Refill the engine cooling system.
    housing.

Oct 18, 2011 | 2004 Chrysler Pacifica

1 Answer

2005 f150 brake pedal moves about 2 inches from side to side


Check up at the mounting bolt under the dash. It sounds like the bolt has come loose. Just follow the brake pedal lever upwards and you will find the mount. Some of the trucks had electrically adjustable pedals. If yours has this feature, it sounds like the adjustment mechanism is in pieces.

Aug 06, 2011 | Ford F-150 Cars & Trucks

2 Answers

2004 ford expedition with adjustable brake and gas pedal. when i depress the button to move the pedals it will barely move them


Hi there nsgpam! It sounds like the electric motors that do the work are worn out. You should be able to get those at an auto parts store but there is a chance that that would be a dealer item. Unfortunately there are some parts that the dealers wont let anyone else sell but them. Check out NAPA, Car Quest or Autozone, or any other large store.

Apr 23, 2011 | 2004 Ford Expedition

1 Answer

I have very short legs and I need to buy a car with adjustable pedals.


Interesting question, I don't think I have ever heard of a car with adjustable pedals. Select a car that nearest fits your needs and then have the pedals modified to suit your stature. Good luck.

Feb 20, 2011 | Cadillac CTS Cars & Trucks

1 Answer

Piece of plastic fell off brake pedal rear brake light stays on sometimes


the piece of plastic that fell off may be from brake light switch. it is located in back of brake pedal arm, on the top. the switch may just need a little adjustment or replaced. have a good day !!

Dec 17, 2010 | Honda Civic Cars & Trucks

1 Answer

Where is heater core located on a 2001 grand caravan and how hard is it too change?


The heater core does not look too hard to change. Here are the directions. It should take a skilled technician with all the correct tools about 1.4 hours to change....you might expect to spend 2 hours or a little more doing the job yourself.
The heater core is located on the driver's side of the HVAC housing, near the driver's right foot.

Removal - FRONT HEATER CORE

WARNING: On vehicles equipped with airbags, disable the airbag system before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the battery negative (ground) cable, then wait two minutes for the airbag system capacitor to discharge before performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to take the proper precautions could result in accidental airbag deployment and possible personal injury or death.

WARNING: Refer to the applicable warnings and cautions for this system before performing the following operation. Failure to follow the warnings and cautions could result in possible personal injury or death.

  1. Remove the silencer boot fasteners located around the base of the lower steering shaft from the dash panel so that it may be pushed aside.
  2. Remove the brake lamp switch from its mounting bracket.
  3. Disconnect the power brake booster input rod (push rod) from the pin on the brake pedal arm.
  4. If equipped with power adjustable pedals, remove the adjustable pedal assembly.
NOTE: Take the proper precautions to protect the carpeting below the heater core from spilled engine coolant and have absorbent toweling readily available to clean up any spills.

  1. Remove the heater core tubes.
  2. Remove the two screws that secure the heater core mounting plate to the HVAC air distribution housing.
  3. If NOT equipped with power adjustable pedals, pull the accelerator pedal upward (Accelerator Pedal) and push the brake pedal downward (Brake Pedal) for clearance to remove the heater core from the air distribution housing.
  4. Remove the heater core by carefully pulling it straight out of the side of the air distribution housing.
Installation - FRONT HEATER CORE

  1. If NOT equipped with power adjustable pedals, pull the accelerator pedal upward and push the brake pedal downward for clearance to install the heater core into the HVAC air distribution housing.
  2. Install the heater core by carefully pushing it straight into the side of the air distribution housing.
  3. Install the two screws that secure the heater core to the air distribution housing. Tighten the screws to 2 Nm (17 in. lbs.).
  4. Install the heater core tubes.
  5. If equipped with power adjustable pedals, install the adjustable pedal assembly
  6. Connect the power brake booster input rod (push rod) to the pin on the brake pedal arm.
  7. Install the brake lamp switch into its mounting bracket.
  8. Install the silencer boot around the base of the lower steering shaft on the dash panel.
  9. Reconnect the negative battery cable.
  10. If the heater core is being replaced, flush the cooling system.
  11. Refill the engine cooling system.

Oct 19, 2010 | 2001 Dodge Grand Caravan

1 Answer

Brake and gas pedals


The vehicle has a optional adjustable brake to increase driver comfort. The brake pedal position is changed in phase with the accelerator pedal. The system is adjusted by pressing the dash-mounted switch that powers the driver motor mounted on the accelerator pedal assembly. The two-way motor operates backward (away from the driver) or forward (toward the driver) to adjust the accelerator pedal directly and the brake pedal through the drive cable attached to the brake pedal assembly.
--------------------
  • Adjustable brake pedal inoperative
  • Switch.
  • Circuit.
  • Motor.
  • Cable.
  • Obstructions
------------------------------------
PINPOINT TEST D: ADJUSTABLE BRAKE PEDAL INOPERATIVE Test Step Result / Action to Take D1 CHECK MOTOR SOUND
  • Allow two minutes for the thermal overload to reset.
  • Operate the adjustable pedal control switch.
  • Can the adjustable pedal motor be heard to operate?
Yes
GO to D2 .

No
GO to D7 . D2 CHECK MOTOR INSTALLATION
  • Check adjustable pedal motor for correct installation.
  • Is the motor installation OK?
Yes
GO to D3 .

No
CORRECT the motor installation. TEST the system for normal operation. D3 CHECK ADJUSTABLE ACCELERATOR PEDAL SYSTEM
  • Disconnect the brake pedal-to-accelerator pedal cable.
    s3a~us~en~file=a0026998.gif~gen~ref.gif
  • Operate the adjustable pedal control switch.
  • Does the adjustable brake pedal operate now?
Yes
INSTALL a new adjustable brake pedal assembly. REFER to Section 206-06 . TEST the system for normal operation.

No
GO to D4 . D4 INSPECT FOR FOREIGN MATERIAL
  • Inspect the adjustable accelerator pedal assembly for foreign material causing a binding condition.
  • Was any foreign material found?
Yes
REMOVE the foreign material. RETEST for normal operation.

No
GO to D5 . D5 CHECK CABLE
  • Detach the adjustable pedal motor cable.
  • Inspect the ends of the brake pedal motor cable for wear or damage.
  • Are the cable ends OK?
Yes
GO to D6 .

No
INSTALL a new accelerator pedal assembly. REFER to Section 310-02 . TEST the system for normal operation. D6 CHECK CIRCUITS FOR SHORT TO BATTERY
  • Key in OFF position. Adjustable Pedal Switch C290
  • Disconnect the adjustable pedal switch C290.
  • Measure voltage at C290-1 and C290-7.
  • Is the voltage greater than 0 V at either pin?
Yes
REPAIR the short to battery. TEST the system for normal operation.

No
GO to D7 . D7 CHECK POWER TO SWITCH
  • Measure the voltage at C290-2 circuit 490 (RD).
  • Is the voltage greater than 10 V?
Yes
GO to D8 .

No
REPAIR circuit 490 (RD). TEST the system for normal operation. D8 CHECK GROUND TO SWITCH
  • Measure resistance to ground at C290-3 circuit 57 (BK) and C290-6 circuit 57 (BK).
  • Is the resistance less than 5 ohms at both pins?
Yes
GO to D9 .

No
REPAIR the open circuit. TEST the system for normal operation. D9 TEST SWITCH
  • Connect fused jumpers between C290-1 and -2 and between C270-7 and -3.
  • Does the adjustable pedal motor run in both directions?
Yes
INSTALL a new adjustable pedal switch. TEST the system for normal operation.

No
GO to D10 . D10 CHECK SWITCH-TO-MOTOR CIRCUITS CONTINUITY
  • Connect: Adjustable Pedal Switch C290.
  • Disconnect: Adjustable Pedal Motor C2001.
  • Measure resistance to ground at both pins of the adjustable pedal motor connector, circuits 1494 (RD) and 1495 (WH).
  • Is the resistance less than 5 ohms at both pins?

Apr 24, 2009 | 2003 Mercury Grand Marquis

1 Answer

1998 Ford Explorer Brake Lights Won't come on


hi assume all brake lights including high level light ? are not working ? 1st check is the fuse ? if it is ok? then next check is the brake stop light switch located at the pedal just near the top of pedal the switch is normaly adjustable and screws into the pedal boxframe that pedals fit /pivot to the switch operates on plunger method ie when pedal pressed the small plunger moves out and puts lights on then when pedal released plunger is pushed back lights off the switch is plastic and has a plug with 2 wires attached to test if plug is defective ? unplug wires from switch then using either a paper clip or piece of wire ? connect /join both wires in plug then sitch ign on if lights work ? switch is defective simple diy to replace cost here in uk for switch approx £4 hope this helps ?

Mar 06, 2009 | 1998 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

134 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...