Question about Toyota Camry

1 Answer

How to remove harmonic balancer - Camry Toyota Cars & Trucks

Posted by on

  • harrod Jul 19, 2008

    trying to replace water pumpon 98 camry 4 cyl

  • shwnmeador Mar 04, 2009

    i have subaru 1998 legacy with about 170,000 miles and the crank is not turning therefore not turning my belts and power is not circulating to power sterring alternator etc. So it drained my battery. To cut to the chase when i touch the crank it jiggles and seems if belt wasnt around it it would pull right off as it is loose. there is a center bolt in middle that i tightened down. there are four holes on front as well not sure if bolts go in these holes? not sure why it would be loose. One mechanic without looking at said that there is a seal that goes bad and that the harmonic balance needs to be replaced. Are there any special tools needed to change harmonic balancer? Or is it just taking off main bolt and replacing unit. I didnt know if was easy or complicated. thanks in advance.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

If you need the service manual for the 2AZFE motor email me i can send you a copy of the cooling system section of it for you

Posted on Jul 22, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have an 2006 dodge stratus.im changeing the front crank seal.do I have to pull the engine out to remove the harmonic balancer?


You should be able to get to the harmonic balancer while it's in the car. Remove right tire( use jack stands to hold the car up- not a jack). remove the inner splash guide and the balancer will be exposed. Using 3 jaw puller to remove harmonic balancer

Harmonic balancer removal DodgeForum com

May 31, 2014 | Cars & Trucks

1 Answer

Harmonic balancer


remove center bolts and with puller remove the harmonic balancer.then after,to replace install harmonic balancer and the center big bolt with air gun tight it until it sit

Aug 07, 2013 | Oldsmobile Delta 88 Cars & Trucks

1 Answer

I need to replace the crank shaft sensor


Yes. Jack the car up securely. you need to take passenger wheel off.remove caliper off . remove rotor. remove shock assembly and wheel bearing assembly slide.axleshaft out of the way.take serpinetine belt off. remove cover so you can see and access harmonic balancer.use impact to take bolt out of harmonic balancer.use wheel puller to take off harmonic balancer. Crank sensor should be right under harmonic balancer.

Jan 05, 2012 | 1994 Oldsmobile 88

1 Answer

I need the location of the harmonic balancer on my 2.2l Ecotec engine. Car is 2004 Chevrolet Cavalier LS.


CRANKSHAFT PULLEY IS THE HARMONIC BALANCER.YOU NEED THESE TOOLS TO REMOVE HARMONIC BALANCER, YOU NEED HARMONIC BALANCER REMOVER AND INSTALLER TOOL.YOU NEED A LARGE PIN SPANNER WRENCH TO HOLD HARMONIC BALANCER IN PLACE WHILE LOOSEN THE HARMONIC BALANCER BOLT.

May 21, 2011 | Chevrolet Cavalier Cars & Trucks

1 Answer

How do i remove harmonic balancer & replace


YOU NEED A HARMONIC BALANCER PULLER TOOL AND A 15M SIX POINT SOCKET TO REMOVE HARMONIC BALANCER BOLT.TURN OFF RADIO AND REMOVE THE DRIVE BELT AND REMOVE THE NEGATIVE BATTERY CABLE. REMOVE THE STARTER SO YOU CAN PUT A LARGE SCREW DRIVER OR LARGE PUNCH TO STICK IN ONE OF THE FLY WHEEL HOLES TO KEEP ENGINE FROM TURNING WHEN YOU LOOSEN THE HARMONIC BALANCE BOLT. ALSO SCREW DRIVER AND PUNCH CAN KEEP ENGINE FROM TURNING WHEN REMOVER THE HARMONIC BALANCER. YOU WILL NEED A HELPER TO HOLD PUNCH OR SCREW DRIVER WHILE YOU LOOSEN THE BOLT. YOU CAN GO TO SEARS OR ANY AUTO PARTS STORE AND BUY HARMONIC BALANCER PULLER.TORQUE HARMONIC BALANCER BOLT TO 76 FT LBS.

Apr 23, 2011 | 2003 Pontiac Montana

1 Answer

How do you replace the harmonic balancer pulley on the 2000 oldsmobile intrigue


The short answer to your question is:

1. Raise the car on the passenger side and remove the front wheel.
2. Remove the belts on the harmonic balancer.
3. Remove the retaining bolt.
4. With a puller, jack the harmonic balancer off of the crank shaft. You can rent a puller at your local auto parts store. It is easiest to access the harmonic balancer through the fender, hence the need to remove the wheel.
5. You should also consider replacing the seal around the harmonic balancer to minimize the possibility of a leak later.
6. Install the new harmonic balancer and tighten the retaining bolt to the specified torque (I don't know this off the top of my head).
7. Replace the belts and wheel, and voila...mission accomplished.

This was a short answer to your question. You may wish to consult a repair manual for illustrations, torque specifications, additional instructions, etc. This job is not for the faint of heart. Good luck!

Feb 19, 2010 | 2000 Oldsmobile Intrigue

2 Answers

Where is the crank sensor located on a 1999 oldsmobile intrigue 3.5 engine???? easy to replace or not...


usually all crankshaft sensors are located right next to the main drive pulley (Harmonic balancer). As far as being easy is concerned some are not so easy as some require the removal of the harmonic balancer to get to it.. but you might be lucky Gm is pretty good at making the Crankshaft sensor accessible without removing the harmonic balancer.

Dec 01, 2009 | Oldsmobile Intrigue Cars & Trucks

1 Answer

I need a how to to change harmonic balancer for 1995 nissan maxima. step by step


First remove right front tire and support vehicle with a jack stand. Remove splash guard lower portion near the harmonic balancer. Remove all drive belts. First remove the A/C alternator belt. Loosen the 14mm bolt at the front of the belt tenioner and then loosen the tensioner bolt (it is the one that stands out, you use a socket on it.). The power steering adjuster bolt with be gained from the bottom. It has a 12mm bolt head on it. You will break the jamb bolt loose first and then loosen the adjusting bolt. Pull down on the belt the help move it after you've loosened it some.Then remove harmonic balancer bolt (19mm).If the harmonic balancer will not slide off the crankshaft then use a two finger gear puller. Place the harmonic balancer bolt back in the crankshaft but do not tighten it. Leave it about a half inch from being all the way in. Next place the puller onto the harmonic balancer (one finger on each side securely press into the belt groove. The center puller bolt will rest against the harmonic balancer bolt head. Tighten the puller bolt and make sure the harmonice balancer bolt does not turn. The balancer should come off at this point.

Aug 26, 2009 | Nissan Maxima Cars & Trucks

2 Answers

Harmonic balancer


what are the steps to removing a harmonic balancers

Oct 18, 2008 | 1997 Chevrolet Corvette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

2,356 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63242 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...