Question about 2004 Chevrolet Cavalier

1 Answer

Oil pan How do I get the oil pan off this thing....04 cav. 2.2L f on the vin

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 2,039 Answers

Remove front exhaut pipe empty oil remove pan clean the engine block of old gasket ins tall pan nothing special hope it help fixya our post thanks pierre

Posted on Jul 18, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the oil pump located 1994 mazda b4000 4.0 litre


The oil pump is in the oil pan.
On 4.0 engines with vin code E you may have to remove the engine to be able to remove the oil pan.

Jan 29, 2013 | Cars & Trucks

1 Answer

Can i remove the gasket in 04 tahoe 4.8


Click here to see oil pan removal guide.

Nov 27, 2012 | 2004 Chevrolet Tahoe

1 Answer

Replacement of the oil pan on a cadillac 2006 DTS


Big job.

gmlogoflat.gif Service Information
bhome.gifbpublication.gifbnumsrchbutton.gifbnews.gifymkbutton.giffeedback.gifbhelp.gif
2006 Cadillac DTS ' DTS VIN K Service Manual ' Document ID: 636855 Oil Pan Removal

    1527739.gif
    tif.gif
  1. Rotate the engine so that the oil pan is facing up.
  2. Remove the oil pan drain plug.

  3. 1373472.gif
    tif.gif
  4. Remove the oil pan bolts.

  5. 1373475.gif
    tif.gif
  6. Remove the oil pan from the lower crankcase oil distribution manifold plate.

  7. 1373484.gif
    tif.gif
  8. Remove and discard the oil pan gasket.

  9. 204585.gif
    tif.gif
  10. Remove the oil level sensor (1).

Jul 29, 2011 | 2006 Cadillac DTS

1 Answer

How to change the oil pump out in ford taurus


It matters if the 8th digit of vin numbers is a U or an S.
For a U: Remove oil pan, remove oil pump retaining bolts, oil pump and shaft.
For a S: You will have to remove the oil pan, front cover, the timing chain, and the crank shaft sprocket to get to the oil pump

Mar 07, 2011 | 2001 Ford Taurus

1 Answer

I have a 96 Chevy Cav. Looks like I have a fairly significant oil leak on the front side of the engine (belt side). It's losing approximately 1/2 quart of oil every 250-300 miles or so. It looks like it's...


Sounds like the front seal is out. You may have to take the engine out of the car to fix it. It requires removing the harmonic balancer to get to the seal.

Oct 02, 2010 | 1996 Chevrolet Cavalier

1 Answer

Need diagram for 2000 ford taurus oilpan


Oil Pan - Removal & Installation3.0L Engine
VIN S Engine
  1. Before servicing the vehicle.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Dual converter Y-pipe Transaxle support bracket Oil pan by following the bolt removal sequence shown

    8d11698.jpg
    Fig. Oil pan bolt removal sequence-2000-04 3.0L (VIN S) engine


    2272e92.jpg
    Fig. Oil pan bolt tightening sequence-2000-04 3.0L (VIN S) engine
Hope helps (remember rated and comment this).

Aug 15, 2010 | 2000 Ford Taurus

1 Answer

Need to change oil pan


e
Cavalier, Sunfire 2001-2005

Oil Pan - Removal & Installation

2.2L (VIN 4) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Negative battery cable Right front wheel Right inner fender splash shield Starter motor and bracket Engine mount strut bracket Oil pan
To install:


672c0b8.jpg

Fig. Exploded view of the oil pan mounting and related components-2.2L (VIN 4) engine
  1. Place a 2mm bead of RTV sealer to the oil pan sealing surface except at the rear seal mounting surface. Using a new oil pan rear seal, apply a thin coat of RTV sealer on the end down to the ears.
  2. Install or connect the following:
    Oil pan with a new gasket. Torque the nuts and bolts to 89 inch lbs. (10 Nm). Engine mount strut bracket. Torque the bolts to 49 ft. lbs. (66 Nm). Starter motor and bracket. Torque the bolts to 37 ft. lbs. (50 Nm). Right fender splash shield Right front wheel. Torque the nuts to 100 ft. lbs. (140 Nm). Negative battery cable
  3. Refill the crankcase.
  4. Start the vehicle and verify no leaks.
2.2L (VIN F) Engine
  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Remove or disconnect the following:
    Engine mount strut bracket Drive belt Lower then upper AC compressor bolts Oil pan bolts Oil pan

    1c9e9c9.jpg

    Fig. Remove/Install the oil pan bolts in this sequence-2.2L (VIN F) engine
To install:
  1. Apply a 2 mm bead of RTV sealant around the perimeter of the oil pan and the oil suction port opening. Do not over apply the RTV. More than a 2 mm bead is not required.
  2. Install or connect the following:
    Oil pan and tighten the bolts to 18 ft. lbs. (25 Nm) AC compressor bolts Engine mount bracket Drive belt
  3. Refill the crankcase.
  4. Start the vehicle and verify no leaks.

2.4L Engine

  1. Before servicing the vehicle, refer to the precautions section.
  2. Drain the engine oil.
  3. Drain the cooling system.
  4. Remove or disconnect the following:
    Negative battery cable Flywheel/converter cover Right wheel Right wheel well splash shield Accessory drive belt Air conditioning compressor lower bolts Transmission-to-engine brace Engine mount strut bracket Radiator outlet pipe bolts Radiator outlet pipe from the oil pan Oil pan to the flywheel cover bolt and nut Flywheel cover stud for clearance Radiator outlet pipe from the lower radiator hose and oil pan Oil level sensor connector Oil pan
To install:
  1. Inspect the oil pan gasket; it is reusable if not damaged.
  2. Install or connect the following:
    Oil pan with the gasket. Torque the M8 bolts to 18 ft. lbs. (24 Nm) and the M6 bolts to 106 inch lbs. (12 Nm).

    2ffc5e9.jpg

    Fig. Oil pan fastener torque specifications-2.4L engine
    Oil pan to the transmission nut Oil level sensor connector Radiator outlet pipe to the lower radiator hose and oil pan Exhaust manifold brace Radiator outlet pipe. Torque the bolts to 124 inch lbs. (14 Nm). Engine mount strut bracket. Torque the bolts to 55 ft. lbs. (75 Nm). Transmission to the engine brace Air conditioning compressor lower bolts. Torque the bolts to 37 ft. lbs. (50 Nm). Accessory drive belt Right splash shield Right front wheel Flywheel/converter cover Negative battery cable
  3. Refill the crankcase.
  4. Refill the cooling system.
  5. Start the vehicle and verify no leaks.

Hope helped (remember rated this help). Good luck.

Oct 22, 2009 | 2001 Chevrolet Cavalier

1 Answer

Vehicle certification label shows my car was made 1-04.car was sold as a 2005. oil cap shows 5w30(for an 04)vin # shows an 05.Chrysler town & Country. are the parts the same for both years ??


yea most cars are made awhile before they are out,i had a 90 talonawd and it was made 4 1989,,,go with the vin,,,2005,whats it say on your registration card?2005 i bet

Oct 12, 2009 | Chrysler Town and Country Cars & Trucks

1 Answer

Oil pan gasket


Well, the F2 means it is a 1992 model. If you have a 2.3L Mustang engine. The vin should be M. it is a 2.3L dual plug igintion(means it has 2 coills,No distributor).If you have a 87 to 89. You have a VIN A engine which is a lil different.

If you have a vin A. According to partsamerica.com(advanceautoparts.com) 1986-1990 oil pan gasket fits. If you have a 92. according to what I just looked up. It says that it will fit. If look up replacement parts. got to gaskets and look for see what vehicles it fits. Sometimes It will tell you all the vehicle that particular gasket will fit..

Jun 08, 2008 | 1993 Ford Mustang

Not finding what you are looking for?
2004 Chevrolet Cavalier Logo

Related Topics:

228 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...