Question about 2002 Nissan Altima

1 Answer

Starter motor how can i remove the starter motor on my nissan tinto

Posted by on

  • Anonymous Feb 05, 2009

    i need to know wat all i have to remove to remove the starter on a 96 nissan altima

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 962 Answers

  • If your testing indicates that the starter must be removed, the first step is to disconnect the negative cable at the battery.
  • It may be necessary to place the vehicle on a lift to gain access to the starter. Before lifting the vehicle, disconnect all wires, fasteners, and so on that can be reached from under the hood.
  • Disconnect the wires leading to the solenoid terminals.
  • To avoid confusion when reinstalling the starter, it is wise to mark the wires so they can be reinstalled on their correct terminals.
  • On some vehicles you may need to disconnect the exhaust system to be able to remove the starter.
  • Loosen the starter mounting bolts and remove all but one.
  • Support the starter while removing the remaining bolt.
  • Then pull the starter out and away from the flywheel.
  • Once the starter is free, remove the last bolt and the starter.
  • Once the starter is out, inspect the starter drive pinion gear and the flywheel ring gear.

Posted on Nov 07, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove a starter motor from a 1994 Nissan Torano 2.7 Diesel


Remove the electrical c able at the end of starter, 2 bolts secure starter to engine, remove these withdraw starter, replace Bendix or whatever is fault.

Jan 11, 2015 | Nissan Cars & Trucks

1 Answer

How to remove starter motor on 2004 Nissan Sentra?


just lossen the two blots and take it out the bottom

Jul 13, 2014 | Nissan Sentra Cars & Trucks

1 Answer

How do you replace a brake light bulb on a nissan tinto


open the cover of brake light and then replace the bulb which situated on rear wheel.

Sep 03, 2011 | Nissan Altima Cars & Trucks

1 Answer

I am trying to replace the starter in my 86 nissan stanza but cant see it


NISSAN STANZA WAGON - Manual Transmission


Q. Where is the starter on a 1986 nissan stanza station wagon and how do you get to it ?


Due to limited access to the starter, it is recommended that the transaxle be removed when servicing the starter.

REMOVAL:

1. Cold vehicle.

Remove 2 mounting bracket bolts, 10 & 12 mm (Figure 1).

Remove top starter motor bolt 14 mm with universal & long extensions.

Raise vehicle on hoist.

Remove front splash pans 10 mm.

Automatic transmission: Drain 2 qts out.

Remove rt-ft wheel 21 mm., & tie rod (Figure 3), axle cap, cotter pin, adj-nut & rubber washer.

Remove ball joint nuts 17 mm., left lower control arm 19mm. & swaybar bracket 14 mm. (Fig 2).

Remove axle nut 36mm (Figure 4), the front tube, catalytic converter heat insulators 10mm, ctr ex-tube 17 mm., and front tube from exhaust system (Figure 5).

Remove long bolt from ft engine mount (next to radiator), 17mm socket (Figure 6, Item A).

Remove tension rod mount 14 mm. Has adj-bracket with rubber insulators (Fig 6, Items B, C).

Remove right side drive shaft bolts that hold shaft to bracket mounted on engine (Fig7) 12mm.

Remove rt-driveshaft.

CAUTION: Transaxle side seals are cut by spline teeth.

Install hoist type transmission jack and wooden block under the transmission/engine. Be certain the transmission is safely balanced on the hoist.

Remove 5 engine crossmember mounts (3 bolts, 2 nuts) 14mm.

Remove nut that attaches crossmember to engine mount.

Loosen stabilizer bar mounts to allow adequate clearance for crossmember to be removed.

Remove following brackets to allow starter assembly to pass through bottom:

tubular support bracket - engine to transaxle

angled support bracket - driveshaft bracket to engine mount

manifold collector stay - (bottom bolts)

Loosen top bolts, remove bracket above driveshaft-holding bracket 14mm.

NOTE: This bracket is slotted to allow it to slide out without completely removing the bolts.

Remove bottom starter motor mounting bolt.

Separate starter assembly from bellhousing, DC all cables/connectors, remove starter motor.

When installing starter, connect cable, install/torque starter bolts.

Nov 03, 2010 | 1986 Nissan Stanza

1 Answer

Need a manual to change the starter on a, 1994 Nissan, Quest mini van + 6 cylinders


http://groups.yahoo.com/group/villagerquest/

Section 03-06: Starting System 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Starter Motor stv~us~en~file=ani_caut.gif~gen~ref.gif WARNING: WHEN SERVICING THE STARTER MOTOR OR PERFORMING OTHER UNDERHOOD WORK IN THE VICINITY OF THE STARTER MOTOR, BE AWARE THAT THE HEAVY GAUGE BATTERY INPUT LEAD AT THE STARTER SOLENOID IS "ELECTRICALLY HOT" AT ALL TIMES. A PROTECTIVE BOOT IS PROVIDED OVER THIS TERMINAL ON ALL VEHICLE LINES AND MUST BE REPLACED AFTER SERVICING. BE SURE TO DISCONNECT THE BATTERY GROUND CABLE BEFORE SERVICING THE STARTER MOTOR.
Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the engine air cleaner (ACL) (9600). Refer to Section 03-12 for the removal and installation procedure.
  1. Slide back the protective boot and remove the nut securing the battery positive cable on the B-terminal of the starter solenoid (11390).
  1. Remove the battery positive cable from the B-terminal.
  1. Disconnect the S-terminal electrical connector.
  1. Remove the two starter motor bolts.
  1. Remove the starter motor (11002) from the vehicle.

Apr 27, 2010 | 1994 Nissan Quest

1 Answer

Replace starter on nissan altima 97


DUE TO RADIO LOCK OUT FEATURE.TURN OFF RADIO BEFORE REMOVING THE NEGATIVE BATTERY.NOW YOU REMOVE NEGATIVE BATTERY CABLE.RAISE VECHICLE AND SUPPORT ON JACK STANDS.MAKE SURE YOU ARE ON LEVEL SOLID GROUND.REMOVE THE AIR INTAKE DUCT AND THE AIR FILTER HOUSING.DISCONNECT THE POSITIVE BATTERY CABLE AND SOLENOID CONNECTOR FROM THE STARTER MOTOR.REMOVE THE STARTER MOTOR MOUNTING BOLTS AND DETACH THE STARTER FROM THE ENGINE.DEPENDING UPON THE YEAR AND ENGINE TYPE THE STARTER SOLENOID ASSEMBLY MAY BE MOUNTED ABOVE THE TRANSAXLE OR BELOW THE INTAKE MANIFOLD.IF NECESSARY TURN THE WHEELS TO ONE SIDE TO PROVIDE REMOVAL ACCESS THEN YOU PUT EVERY THING BACK VISA VERSA.

Jun 14, 2009 | 1997 Nissan.5 Altima

1 Answer

My 95 nissan quest


2 hour job from top driver side of engine.

Starter Motor stv~us~en~file=ani_caut.gif~gen~ref.gif WARNING: WHEN SERVICING THE STARTER MOTOR OR PERFORMING OTHER UNDERHOOD WORK IN THE VICINITY OF THE STARTER MOTOR, BE AWARE THAT THE HEAVY GAUGE BATTERY INPUT LEAD AT THE STARTER SOLENOID IS "ELECTRICALLY HOT" AT ALL TIMES. A PROTECTIVE BOOT IS PROVIDED OVER THIS TERMINAL ON ALL VEHICLE LINES AND MUST BE REPLACED AFTER SERVICING. BE SURE TO DISCONNECT THE BATTERY GROUND CABLE BEFORE SERVICING THE STARTER MOTOR.
Removal
  1. Disconnect the battery ground cable (14301).
  1. Remove the engine air cleaner (ACL) (9600). Refer to Section 03-12 for the removal and installation procedure.
  1. Slide back the protective boot and remove the nut securing the battery positive cable on the B-terminal of the starter solenoid (11390).
  1. Remove the battery positive cable from the B-terminal.
  1. Disconnect the S-terminal electrical connector.
  1. Remove the two starter motor bolts.
  1. Remove the starter motor (11002) from the vehicle.

May 27, 2009 | 1994 Nissan Quest

Not finding what you are looking for?
2002 Nissan Altima Logo

Related Topics:

175 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

79186 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...