Question about 2003 Hyundai Accent

1 Answer

PIN CODE I lost my key , I need PIN CODE inorder to program new key. NOTE : 1- my VIN is : NLHCG41F04Z031915 2-I have tool to program Keys . 3- don't tell me about dealership .

Posted by on

  • Anonymous Dec 10, 2008

    I also lost the pin code. Hyundai want to replace all the locks

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Hyundai Master
  • 60,971 Answers

Have you called the dealer?

Posted on Nov 07, 2008


Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How would I start a 2000 2.4 litter Mitsubishi triton glx using a non coded key


Hi Russell, Im AL the owner of Big As Auto Repair.

Russell, you cannot start a security installed vehicle with a none security key. If you have lost your key to the vehicle then here's what you can do. Take the last 8 of your VIN Number and your vehicle to the Mitsubishi Dealer and they can cut and program a new key to the security module. NOTE: Another way to do this is to have the dealer cut a new key for the vehicle and then call around to find a lock smith that has the ability to program the key to the vehicle. NOTE: I would check to see which way is cheaper. To Tow the vehicle OR have a lock smith come to you. Hope this helps and please visit my auto-repair-website here: http://www.bigasautorepair.com/

Dec 12, 2015 | Mitsubishi Cars & Trucks

2 Answers

Codes b2799


Error Code: B2799
Description:
Engine Immobilizer.
Trouble Area:
-
Wire harness.
- Immobilizer or ECM is water contaminated.
- ECM.
NOTE: If the car runs fine, there is nothing wrong. Simply delete the code with diagnostic computer and enjoy.

Apr 25, 2014 | 2006 Toyota Camry

2 Answers

Where is the key code on a 2001 ford taurus


give the dealer the vin number then he can make a new key 4 ya

Aug 13, 2012 | 2001 Ford Taurus

1 Answer

Programing radio.changed battery.vin#wauga84a1sn085169.1995audi A6


IMPORTANT NOTE: You must have the security anti-theft code for yours Audi Concert radio from the car manufacturer!
For Audi Concert the sequence of programming is:
1. Push simultaneous "SCAN" and "RDS" keys until on the screen will appear "1000" displayed.
2. Release keys. No more push on "SCAN" and "RDS" keys because otherwise number "1000" will be considered as first safe code attempt.
3. By the #1 key you will set up the first safe code digit.
4. By the #2 key you will set up the second safe code digit.
5. By the #3 key you will set up the third safe code digit.
6. By the #4 key you will set up the four-th safe code digit.
7. Then push again simultaneous "SCAN" and "RDS" keys for confirm this safe code. On the screen will be displayed "SAFE" notice. Release keys! For few seconds a radio frequence will be displayed. The radio is now ready for use!

Please rate my response. Thanks!

Apr 11, 2010 | 1995 Audi A6

1 Answer

VW Sharan (2000model) - Recoding Keys


Programming
When
Key buttons operated repeatedly while vehicle out of range and system becomes inoperative. Key added or replaced. System malfunction.
How
Obtain all keys fitted with remote control. Close all windows and doors. Insert key into driver's door lock. Turn key to unlock position 3 times. Remove key.
NOTE: Hold key in unlocked position for 0,5 second.
Programming mode activated (driver's door LED illuminated). Carry out the following within 20 seconds: Point key at infrared receiver. Located near rear view mirror. Press and hold lock button within 5 seconds Fig. 1 [1]. Press unlock button 3 times Fig. 1 [2]. Release lock button Fig. 1 [1]. Correct programming indicated by driver's door LED flashing. Repeat above procedure within 15 seconds to program remaining keys. To exit programming mode and extinguish LED: Wait 15 seconds.
NOTE: A maximum of 4 keys can be programmed.

Feb 04, 2010 | 2000 Volkswagen Jetta TDI

3 Answers

Lost Key


yes they will need the vin and id

Jan 31, 2010 | 2002 GMC Envoy

1 Answer

2001 mountaineer It has a touchpad lock on the outside on the driver door. How can I get this working and programmed?


If you don't have the original factory code you'll need to contact Ford/Mercury customer service through their web site and provide the VIN for the vehicle. Once you have the original code, you can program your own number by following these steps:

1. Enter the factory set code.
2. Within 5 seconds press the 1-2 key
3. Enter your personal 5-digit code. Each number mus be entered within 5 seconds of each other.
4. Doors will lock and then unlock to confirm that your new code has been entered and accepted.

NOTES:
1. The factory code will still work even after you have entered your new personal code.
2. Entering a new personal code will erase the previous personal code.

BillB

Jan 18, 2010 | 2001 Mercury Mountaineer

1 Answer

I lost my key and i have to cut a new one. I need the key code for cutting a new one and how to programme it. Thank you


no programming that one, get your VIN and title or registration, stop at a mazda dealer and theyll cut you one by the VIN number

Aug 27, 2009 | 1998 Mazda 626

1 Answer

Programming instructions for a 1999 Chrysler 300M remote fob


Manual Programming Procedure (non scan tool)
1. Connect pin 1 of the 16-way data link connector to chassis ground or to pin 4 of the 16-way data link connector.
2. Close all doors, turn ignition key to off.
3. Turn ignition key to Accessory.
4. Turn ignition to off, door locks will cycle once (in programming mode).
5. For each key FOB, press any button 3 times in a row to program code. When programming is complete, the door locks will cycle once.

NOTE:
IF A SECOND KEY FOB REQUIRES PROGRAMMING, IT MUST BE PROGRAMMED WITHIN 1 MINUTE OF PROGRAMMING
THE FIRST FOB PROGRAMMING. PRESS ANY BUTTON ON THE SECOND FOB 3 TIMES TO PROGRAM ITS CODE. WHEN PROGRAMMING IS COMPLETE, THE DOOR LOCKS WILL CYCLE ONCE.

6. The programming mode finishes after the following:
a. Programming of two key FOBS is completed.
b. One minute has passed since programming.
c. Pin 1 of 16-way data link connector is removed from ground connection.
d. Ignition switch is turned on.
e. Any of the doors are opened.

Apr 09, 2009 | 1999 Chrysler 300M

Not finding what you are looking for?
2003 Hyundai Accent Logo

Related Topics:

329 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...