Question about Chevrolet Blazer

1 Answer

I need to know where the plug is located to preform a rad flush for my 97 chevy blazer.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 6 Answers

Lower left facing the fire wall on you radiator.

Posted on Jul 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What years can be interchangeable with a 98 chevy blazer


97-2003 are the same pumps on Chevy.On the GMC Jimmy truck,4.3 is also 97-2003.

Dec 06, 2012 | 1996 Chevrolet Blazer

1 Answer

A diagram of the flushing of a radiator and block of a chevrolet blazer LS 2000


Theres no such thing as a diagram, here are the draining instructions, hope this helps...
  • 1-Place a large drain pan beneath the radiator drain plug. The drain plug is located on the passenger side at the very bottom of the radiator on the engine side.

  • 2-Make sure the engine is cool. Open the hood of the truck and remove the radiator cap.
  • 3-Loosen the drain plug. On the 2000 Blazer, the drain plug is a wing-nut type of plug. Twist it with your fingers until the coolant begins to drain.

  • *To flush the block, once you have drained the radiator, run the engine for a bit untill the temp gauge goes up to normal, then the coolant will have been evacuated from the block. DO NOT leave the engine on, once it reaches normal temp, (this will happen quick) turn off right away, otherwise you'll be forking out a few hundred $$$ to fix the worped heads.
    4-Tighten the drain plug with your fingers once the coolant has drained fully from the radiator. Remove the drain pan and dispose of the used coolant properly.
    Some service stations will take and recycle your used coolant.
    Hope this helps...



  • Read more: How to Drain a Radiator From a 2000 Chevy Blazer ' eHow.com http://www.ehow.com/how_6357264_drain-radiator-2000-chevy-blazer.html#ixzz1VS4RBufX

    Aug 19, 2011 | 2000 Chevrolet Blazer

    1 Answer

    My chevy blazer it hasnt overheated all the way to the red zone but i think cuz i dont let it cuz when i see the gadget go 3/4 high it is the red zone left and i turn off the engine before it gets worse...


    I had my chevy s10 overheat due to poor air circulation through the cooling fins on the rad. I looked on the outside of the rad and found that the cooling fins were plugged solid with dirt and rocks. I removed the rocks and dirt using a hose and dental pick, and the overheating problem stopped. As long as the cooling system isn't leaking, I can't think of another reason for it to lose coolant.

    Feb 09, 2011 | 1996 Chevrolet Blazer

    1 Answer

    How to replace thermostat sensor on 2000 chevy blazer


    located around upper rad hose at engine by the thermostat 1 plug two wire connector should be yello and black

    Dec 05, 2010 | 2000 Chevrolet Blazer

    1 Answer

    How to flush the radiator(cooling system) on 1995 chevy lumina


    Wait until motor is cool. remove rad cap and loosen rad drain pet **** under rad. If you can't loosen it or cant find it, remove lower rad hose. let all antifreeze drain. Close pet **** or replace rad hose. Fill with water and rad flush(you can get the flush from an auto supply store or wallmart). Run for the recommended time on rad flush bottle. Wait for motor to cool. Then drain out water. Refill with 50% prestone and distiled water.

    Aug 12, 2010 | 1995 Chevrolet Lumina

    1 Answer

    Where is the radiator drain plug located on a 97 chevy 1500 Z71? I'm trying to flush the radiator,but cannot find it.


    It's located on the drivers side of the radiator opposite of the lower radiator hose. Note: you may be better off disconnecting the lower radiator hose, it's common for the drain plug to break or the O-rings to split causing more work to drain the radiator. That's why most tech's will drain the radiator from the lower radiator hose, less chance of breaking the radiator drain plug and most new cars now don't come with a drain plug to the radiator.

    Mar 05, 2010 | 1997 Chevrolet C3500

    2 Answers

    My 2002 Chevy Malibu is overheating. I found that


    If your car is equipped with a 3.1 or a 3.4 litre V6 and you have preformed all of the above listed work then I would have to say its the intake manifold gaskets. They commonly blow on these motors. Just a design flaw, nothing but replacing them when they leak can fix this. Also run a coolant pressure test on the system to check for minor things like a leak that you cant see from visual inspection. Hope this helps.

    757Nate

    Nov 21, 2009 | 2002 Chevrolet Malibu

    1 Answer

    Firing order for 97 chevy blazer


    Firing order is 1-6-5-4-3-2. Distributor cap should be numbered. Number one cylinder is front on driver's side (3 and 5 follow on same side). Number 2 is front on passenger's side (followed by 4 and 6).

    Apr 29, 2009 | Chevrolet Blazer Cars & Trucks

    2 Answers

    Engine swap


    95-94-93 4.3 vortec are compatable engines. 97 4.3 will fit but will have problems with sensors and computer

    Dec 06, 2008 | 1995 Chevrolet Blazer

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    58 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    60667 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21936 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6811 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...