A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones). click here to download the app (for users in the US for now) and get all the help you need. Good luck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Sunroof Description and Operation (One Connector System)
This diagnostic procedure is to be used for the 1 connector Sunroof System that combines the sunroof control module with the sunroof motor/actuator.
The Sunroof System consists of the following components:
• BATT MAIN 2 Fuse 50 A
• Body control module (BCM)
• RAP relay
• S/Roof Fuse 20 A
• Sunroof module (includes sunroof motor/actuator)
• Sunroof switch
The Sunroof System is controlled by the sunroof switch and the sunroof motor/actuator assembly.
When the ignition is turned to RUN or ACCESSORY, or when the retained accessory power (RAP) system is active, the body control module (BCM) applies a ground to the RAP relay in the instrument panel (I/P) fuse block. This activates the RAP relay and allows battery positive voltage to be applied through the SUNROOF Fuse to the sunroof module. Ground for the sunroof module is supplied from G302.
The sunroof can be placed in 3 preset positions:
When the sunroof switch is placed in the OPEN position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof motor/actuator then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the full open position.
When the sunroof switch is placed in the VENT position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof module then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the VENT position.
When the sunroof switch is placed and held in the CLOSED position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch close signal circuit. The sunroof module then applies voltage to the sunroof motor close control circuit and applies a ground to the sunroof motor open circuit. The sunroof motor then closes the sunroof.
The sunroof can be placed in any preferred open position when:
• The sunroof is in the fully opened position by pressing and holding the sunroof switch in the CLOSE position until the panel has reached the desired position then release the CLOSE switch in order to stop the sunroof
• The sunroof is opening, it can be stopped by momentarily pressing either side of the switch.
The sunroof control module, sun roof actuator, and the sunroof motor are integral parts of the sunroof module assembly and are not service separately.
Your best bet , take it to a qualified repair shop or buick dealer .
OK given that this won\'t help the original enquirer but for all those who like me have had this prob and found themselves here well here\'s a solution that\'s not complex on all isuzu trooper/bighorns mk 2s ( as far as I know) early 90s have a manual over ride . You need a coin or flat head screwdriver and a 6mm Alan key. Now look above the the back seats in the middle you will find a little bung use coin / screwdriver to turn it out don\'t dig it out. Inside you will find a small Alan bolt turn with Alan key to open or close sunroof (Isuzu hand book 1992 page 4_17) PS there is a tool for the job located in the glove box if you still have it!!
HAVE SAME PROBLEM ON MY ALERO , WOULD CLOSE TO VENT POSITION ALL OTHER FUNCTIONS WORKED FINE. TALKED TO A MECH. FRIEND AND FOUND A WAY TO CLOSE MANUALLY BUT YOU DO HAVE TO DROP FRONT LEFT CORNER OF HEADLINER. THE MOTOR IS UNDER SUNVISOR AREA AND YOU'LL NEED AN ALLEN(SPELLING)SOCKET TO CLOSE ROOF
Some sunroofs have a open switch like the drivers window. You push it and the window will open automaticly. The button on your sunroof could be jammed so even though you can close it as soon as you release it, it will auto open on it's own.
Hey Paul, there are limit switches integrated into the motor on your sunroof, usually if it stops completely its because it detected a restriction, such as leaves, or dirt, if there are no visual sign then with the key on hold the switch to the full open position for 10-12 sec then hold it in the close position for the same, cycle the key and see if it reset. The motor can fail as well but it's not very common.. Do u hear any clicking from the motor area when this occurs, also check all fuses to be safe as well,..