Question about 1984 Porsche 944

2 Answers

NO GEARS MY 1984 944 WILL NOT GO INTO ANY GEAR, INCLUDING REVERSE WHAT SHOULD I CHECK? ALSO, WHERE CAN I GET A DIAGRAM OF ALL WORKING PARTS FOR A 1984 944 WITH A MANUAL TRANSMISSION?

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

  • Expert
  • 55 Answers

I think you mean bleed the slave cylinder first. does the clutch pedal have any resistance? Goto www.clarks-garage.com and see if you find what you need. That site is awesome for fixing any 944.

Posted on Apr 22, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,050 Answers

Refill and bleed the clutch master cylinder.

Posted on Dec 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Audi A3 reverse lights not working


I don't think any parts are needed, it sounds like a problem that could be fixed with a simple cable or linkage adjustment

Mar 05, 2014 | 2007 Audi A3

1 Answer

Explorer 5 speed manual gear box sliping out of gear


The trans has to come out & come apart
& be gone thru to replace worn gear syncros
& any other parts

To be that bad in all gears, it hasn't been treated
very well

Mar 02, 2013 | Ford Explorer Cars & Trucks

1 Answer

Nissan largo 1994 AUTO ...when selecting a gear with lever it shift into it smoothly all 3 foward gears work fine you can hear and feel transmission doing it job , but when selecting reverse it goes into...


Before starting with the hard ones, start with the usual culprit like fluid levels and the condition if it needs repairing. If there are debris in the system it could clog the valves for the reverse gear which makes it difficult or impossible to engage. This unfortunately would need inspection of the transmission from the outside. Check the linkages and the lines and look for leaks to inspecting the internal parts especially the gears.

Jul 22, 2011 | Nissan Leaf Cars & Trucks

1 Answer

When u come out reverse the gear stick goes stiff, hard to go back into first gear. been advised might be a pin, found piece of plastic under gear stick cover round shaped.


Hi,
Fiats do not enjoy a sound reputation for their transmissions. If you are confident in your skills, remove the cover / boot that surrounds the gear stick. and check it carefully for fitting into the housing. There may be a plastic of fibre cup that the ball of the gear stick rides in. depending on the locating device for this "bearing" will affect the movement of the gear stick. If you can lift the gearstick and it shows lots of slop, then the 'bushing is no longer holding the gearstick in the correct neutral position which enables each gear, including reverse, to be selected easily. The reason for the 'bushing' failing will have to be ascertained, it may be a simple fix, or it may be lots of aggravation, depending if the parts are all present and can be salvaged.

Good luck.

Feb 01, 2011 | 2006 Fiat 124

1 Answer

Vechile will not shift into park or reverse


The first thing to check is the linkage. Sometimes the linkage will slip, Block the wheels on the car (both front and rear) to prevent rolling. Locate the shift linkage on your transmission, and loosen the nut. You should be able to move the shift lever through all the gears, including "P" and "R". Place the transmission shift lever in "Park" (on the transmission) then move the shift lever (inside the car) in the "P" position and tighten the nut (not a bad idea to use a new locking nut here) You should now be able to shift through all gears. If this does not work, you have a more serious problem that may include a worn or broken belt or broken parking pawl inside the transmission.

Apr 05, 2010 | 1994 Cadillac DeVille

1 Answer

Not shifting into overdrive on a 1500 chevy pick-up all four gears work but that one is there some kind of sensor that need to be replace.i have the 4l60e series trams


I'm not sure if your saying all four gears including reverse but that transmission only has four forward gears. Fourth gear is overdrive

Nov 28, 2009 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Gear stuck on reverse. Put on drive gear still in


Have your gearbox checked. Stucked up issue,
is often caused by a worn out part, (Bearing, or
bushing, or geartrain.

Sep 21, 2009 | 1965 Ford Mustang

1 Answer

1988 Ford Bronco Transmission Issues


is the idle speed correct? do you shift into second before trying to engage reverse?, is the clutch ok, this is most likely not the trans at all but one of the above issues, the clutch is my guess.

Sep 14, 2009 | 1988 Ford Bronco

2 Answers

Reverse gear fiat x1/9 doesn't go in ?


These gearboxes were notorious for failing the reverse gear. The reverse gear wears out easily and keeps popping out. You can try shifting the gearbox into 3rd gear before going into reverse. This helps align the syncros in the tranny. Of course make sure you are not moving or if you are have the clutch depressed when shifting. You can also try http://www.international-auto.com/ for parts. They may be able to help you.

Feb 08, 2009 | 2006 Fiat X1/9

Not finding what you are looking for?
Cars & Trucks Logo

363 people viewed this question

Ask a Question

Usually answered in minutes!

Top Porsche Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60769 Answers

Dave  C
Dave C

Level 3 Expert

1050 Answers

Are you a Porsche Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...