Question about Acura Integra

1 Answer

Power steering i've recently disconnected my power steering bottle on an honda integra. but i forgot where those three hose goes too.

Posted by on

  • foolz97 Jul 18, 2008

    next time try to remember

×

1 Answer

There is usually paint on the side of each hose and a splodge beside the hole on the pump.

Posted on Jul 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you change fluid in power steering system


You raise the front of the car & support it if necessary,
to put a bottle under it,such as an old washer fluid bottle

Then remove the steering pump return hose from the fluid
container

Put that hose into some plastic tubing & into the empty bottle

Remove the injector fuses, so the motor gets no fuel

Crank the motor & the old fluid goes into the bottle


Add new fluid Dex/Merc or Mercon V to make sure the
container has fluid as you flush out the old

When done,return the return hose,clean up & start the motor
Turn wheels lock to lock a couple times,put it on the ground
& check the fluid level

Change trans & power steering every 3 years or they will
fail for sure.

Those two fluids will not remove heat after 2 or 3 years
in service.

Jul 15, 2014 | 1999 Mercury Sable

1 Answer

Acura Legend Power Steering ($500+) to repair??!!


check the power stearing line.they usually leek before a rack will.there manny fitings on this system. it could also be a rubber washer on the fiting.

Mar 29, 2013 | 1995 Acura Legend

1 Answer

Need to change coolant recovery tank can a anyone do it


Yes you can do it yourself

Degas Bottle Removal
  1. Drain radiator (8005) until engine coolant is out of degas bottle. Disconnect radiator overflow hose (8075) and engine coolant vent hose at degas bottle.
  1. Remove power steering oil reservoir retaining screws and position power steering oil reservoir (3A697) out of the way.
  1. Remove degas bottle return hose and clamp. Remove degas bottle retainers and remove degas bottle.
Installation
  1. Position degas bottle in vehicle and install retaining screw and nut. Tighten retaining bolt and nut to 9-12 Nm (80-106 lb-in).
  1. Connect degas bottle hose and clamp to degas bottle.
  1. Position power steering oil reservoir onto degas bottle and install retaining screws securely.
  1. Connect radiator overflow hose and engine coolant vent hose to degas bottle.
  1. Fill and bleed engine cooling system as described. Check for coolant leaks and proper engine coolant level after engine reaches normal operating temperature.


    q3699b.gif


    Item Part Number Description 1 8100 Radiator Cap 2 - Nut (1 Req'd) 3 - Bolt and Retainer (1 Req'd) 4 - Nut (1 Req'd) 5 - Bolt (1 Req'd) 6 - Coolant Recovery Hose 7 - Coolant Return Hose 8 - Coolant Recovery Hose 9 8A808 Degas Bottle A - Tighten to 9-12 Nm (80-106 Lb-In)
Hope this helps.

Zeppelinx12

Mar 08, 2011 | 1999 Ford Taurus

1 Answer

I need to know how to take the power steering off a 1997 dodge caravan?


Power Steering Pump-Let me know if you need to take the power steering gear off: Removal & Installation 2.4L Engine To Remove:
  1. Disconnect and isolate the negative battery cable.
    • Remove as much fluid as possible from the power steering fluid reservoir using a siphon pump.
    • Remove the drive belt from the power steering pump.
    • Loosen the nut securing the front power steering pump bracket to the aluminum bracket.
    • Raise and safely support the vehicle.
    • Place a drain pan under the vehicle to catch the power steering fluid.
    • Disconnect the connector from the oxygen sensor at the rear engine mount bracket. NOTE: The exhaust system needs to be moved to allow room for power steering pump removal.
    • Remove the bolts and nuts securing the catalytic converter to the exhaust manifold.
    • Disconnect the exhaust system hangers from the brackets. Move the exhaust system rearward and left as far as possible.
    • Raise the heat sleeve to expose the clamp and then disconnect the fluid return hose from the steel tube. Allow the fluid to drain.
    • Remove the accessory drive splash shield.
    • Remove the supply hose coming from the reservoir from the power steering pump. Drain the fluid from the hose.
    • Disconnect the pressure hose from the pump. Drain off excess fluid from the hose.
    • Remove the return hose from the pump. Allow the fluid to drain from the tube.
    • Remove the nut from the rear of the pump to the cast mounting bracket.
    • Loosen the three bolts securing the pump to the front mounting bracket. Then remove the nut and remaining bolt.
    • Remove the power steering pump and the front bracket from the cast bracket on the engine as an assembly through the exhaust tunnel.
    • Remove the three bolts attaching the front bracket to the power steering pump and separate the power steering pump from the front bracket.
To Install:
  1. Install the power steering pump through the exhaust tunnel of the vehicle.
  2. Loosely install the nut on the rear of the pump to hold the pump to the bracket.
  3. Install the front bracket on the pump and install the three bolts loosely.
  4. Install the nut and bolt securing the bracket to the cast bracket.
  5. Tighten the three front bracket-to-pump bolts to 40 ft. lb. (54 Nm).
  6. Connect the pressure hose to the power steering pump. Make sure to inspect the o-ring and replace as needed. Tighten the fitting to 275 in. lb. (31 Nm).
  7. Connect the low pressure return hose to the power steering pump.
  8. Connect the supply hose from the reservoir to the pump. Make sure the hose is not near drive belt.
  9. Install the drive belt and splash shield.
  10. Connect the fluid return hose to the steel tube on the cradle and cover with the heat shield sleeve.
  11. Properly position the protective heat sleeve over the return hose. Secure the heat sleeve with a tie strap to the hose to keep it in place.
  12. Install the exhaust system.
  13. Connect the oxygen sensor wiring connector to the vehicle wiring harness.
  14. Lower the vehicle.
  15. Connect the negative battery cable.
  16. Fill and bleed the power steering system.
  17. Check for leaks.
3.0L Engine To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Remove as much fluid as possible from the power steering fluid reservoir using a siphon pump.
  3. Remove the drive belt from the power steering pump.
  4. Raise and safely support the vehicle.
  5. Place a drain pan under the vehicle to catch the power steering fluid.
  6. Disconnect the connector from the oxygen sensor at the sensor wiring harness grommet on the floor pan. NOTE: The exhaust system needs to be moved to allow room for power steering pump removal.
  7. Remove the bolts and nuts securing the catalytic converter to the exhaust manifold.
  8. Disconnect the exhaust system hangers from the brackets. Move the exhaust system rearward and left as far as possible.
  9. Raise the heat sleeve to expose the clamp and then disconnect the fluid return hose from the steel tube. Allow the fluid to drain.
  10. Remove the accessory drive splash shield.
  11. Remove the supply hose coming from the reservoir from the power steering pump. Drain the fluid from the hose.
  12. Disconnect the pressure hose from the pump. Drain off excess fluid from the hose.
  13. Remove the two bolts securing the pump to the alternator/power steering pump/belt tensioner bracket.
  14. Remove the pump from the bracket and remove it from the vehicle through the exhaust tunnel on the floor pan.
To Install:
  1. Install the power steering pump through the exhaust tunnel of the vehicle.
  2. Install the pump on the bracket with the two mounting bolts. Tighten the two bolts to 40 ft. lb. (54 Nm).
  3. Install the pump rear support bracket. Tighten the nut and bolts to 40 ft. lb. (54 Nm).
  4. Connect the pressure hose to the power steering pump. Make sure to inspect the o-ring and replace as needed. Tighten the fitting to 275 in. lb. (31 Nm).
  5. Connect the low pressure return hose to the power steering pump.
  6. Connect the supply hose from the reservoir to the pump. Make sure the hose is not near drive belt.
  7. Install the drive belt and splash shield.
  8. Connect the fluid return hose to the steel tube on the cradle and cover with the heat shield sleeve.
  9. Properly position the protective heat sleeve over the return hose. Secure the heat sleeve with a tie strap to the hose to keep it in place.
  10. Install the exhaust system.
  11. Connect the oxygen sensor wiring connector to the vehicle wiring harness.
  12. Lower the vehicle.
  13. Connect the negative battery cable.
  14. Fill and bleed the power steering system.
  15. Check for leaks.
3.3L & 3.8L Engines To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Remove as much fluid as possible from the power steering fluid reservoir using a siphon pump.
  3. Raise and safely support the vehicle.
  4. Disconnect the connector from the oxygen sensor at the sensor wiring harness grommet on the floor pan. NOTE: The exhaust system needs to be moved to allow room for power steering pump removal.
  5. Remove the bolts and nuts securing the catalytic converter to the exhaust manifold.
  6. Disconnect the exhaust system hangers from the brackets. Move the exhaust system rearward and left as far as possible.
  7. Place a drain pan under the vehicle to catch the power steering fluid.
  8. Raise the heat sleeve to expose the clamp and then disconnect the fluid return hose from the steel tube on the cradle. Allow the fluid to drain into the pan.
  9. Remove the accessory drive splash shield.
  10. Remove the drive belt from the power steering pump.
  11. Remove the supply hose coming from the reservoir from the power steering pump. Drain the fluid from the hose.
  12. Disconnect the pressure hose from the pump. Drain off excess fluid from the hose.
  13. Disconnect the return hose from the pump. Drain the fluid into the drain pan.
  14. Remove the power steering pump rear support bracket.
  15. Remove the three bolts securing the pump to the alternator/power steering pump/belt tensioner bracket.
  16. Remove the pump from the bracket and remove it from the vehicle through the exhaust tunnel on the floor pan.
To Install:
  1. Install the power steering pump through the exhaust tunnel of the vehicle.
  2. Install the pump on the bracket with the three mounting bolts. Tighten the bolts to 40 ft. lb. (54 Nm).
  3. Install the pump rear support bracket. Tighten the fasteners to 40 ft. lb. (54 Nm).
  4. Connect the pressure hose to the power steering pump. Make sure to inspect the o-ring and replace as needed. Tighten the fitting to 275 in. lb. (31 Nm).
  5. Connect the low pressure return hose to the power steering pump.
  6. Connect the supply hose from the reservoir to the pump. Make sure the hose is not near drive belt.
  7. Install the drive belt and splash shield.
  8. Connect the fluid return hose to the steel tube on the cradle and cover with the heat shield sleeve.
  9. Properly position the protective heat sleeve over the return hose. Secure the heat sleeve with a tie strap to the hose to keep it in place.
  10. Install the exhaust system.
  11. Connect the oxygen sensor wiring connector to the vehicle wiring harness.
  12. Lower the vehicle.
  13. Connect the negative battery cable.
  14. Fill and bleed the power steering system.
  15. Check for leaks.
prev.gif next.gif

Oct 13, 2010 | 1997 Dodge Caravan

1 Answer

My power steering oil is leaking


First you need to find the sorce of the leak, be it in a hose or in the resivoir. I personally use Lucas power steering sealer available at most parts stores, and Walmarts I believe. Follow the instructions on the bottle, but it has cured numerous power steering leaks for me.

Dec 11, 2009 | 1992 Honda Accord

2 Answers

I poured brake fluids in my powered steering will it damage my car please help


I will say it is not a good thing and the best thing to do is disconnect your power steering hose, drain it, pour a fresh bottle of steering fluid in it, run the engine and drain it again. Refill the power steering reservoir. Jack the front end off the ground and then turn the steering wheel back and forth about 5 times to bleed the system. You should be fine.

Oct 28, 2009 | 1995 Acura Integra Coupe

1 Answer

Replace a coolant reservior on a 1999 ford taurus


If you need Illistration I Can Email it to you Im at
rejakwilson @ aol.com

Removal

CAUTION: Do not mix Standard (green) Coolant with Extended Life Coolant (orange). If mixing occurs, drain engine cooling system and refill with originally equipped coolant type. If this contamination occurs, the service change interval on Extended Life Coolant will be reduced from 6 years/150,000 miles to 3 years/30,000 miles.

  1. Drain radiator until engine coolant is out of degas bottle. Disconnect radiator overflow hose and engine coolant vent hose at degas bottle.
  2. Remove power steering oil reservoir retaining screws and position power steering oil reservoir out of the way.
  3. Remove degas bottle return hose and clamp. Remove degas bottle retainers and remove degas bottle.
Installation
  1. Position degas bottle in vehicle and install retaining screw and nut. Tighten retaining bolt and nut to 9-12 Nm (80-106 inch lbs.)
  2. Connect degas bottle hose and clamp to degas bottle.
  3. Position power steering oil reservoir onto degas bottle and install retaining screws securely.
  4. Connect radiator overflow hose and engine coolant vent hose to degas bottle.

Aug 28, 2009 | 1999 Ford Taurus

1 Answer

I'm trying to replace the power steering pump on my acura integra 1994 how can i replace it


drain power steering fluid.disconnect the inlet and out let hoses from power steering pump.remove belt by loosen the adjusting bolts on pump bracket.remove power steering bolts and remove pump.put in new power steering pump torque it 17 ft lbs . connect hoses .put belt back on adjust the belt tension. add fluid check level . bleed the air from system.

Apr 13, 2009 | 1990 Acura Integra Hatchback

1 Answer

Loss of power steering after changing resevior bottle


Your friend wouldnt happen to know what he put in? Before it goes to far drain the system and add proper fluid, if it is improper fluid maybe it wont be to late.

Jan 29, 2009 | 1996 Volkswagen Jetta

1 Answer

Power steering leak


three things to check the powersteering hose, the pump and the steering rack itself usualy the power steering hose and the steering rack usualy go bad in them

Nov 15, 2008 | 1991 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

70 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...