Question about Chevrolet Aveo

1 Answer

I need torque specs for a 2004 chevy aveo front hub. installing new rotors

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Torque specs. to a 2001 chevrolet malibu 3.1 engine with also needing head and manifold torque specs. as well.

Posted on Sep 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front brake torque specs 2010 chevy aveo lt


Just tighten hard as you can,I have never torque my brake parts.

Jun 29, 2015 | Cars & Trucks

3 Answers

I need the Torque specs for a 2006 ford escape breaks front and back please


Pad material will cause these problems.... Buy good Cermic pads and new rotors and you won't have that problem

Jan 22, 2015 | 2006 Ford Escape

2 Answers

What is the torque specs for a hub and bearing assembly on a 2001 four wheel drive chevy s10 blazer



Adjustment

The wheel bearings on these vehicles are not adjustable. If the bearings become loose or make noise, they must be replaced.


Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions section.
  2. On 4WD vehicles, remove wheel center cap, if equipped, and the drive axle nut and washer
  3. Raise and support the vehicle.
  4. Remove or disconnect the following:
    NOTE Lay the hub and bearing on the wheel studs on the outboard side. This will avoid damaging the bearing seal.


    Tire and wheel Caliper, leaving the fluid lines connected Brake rotor Halfshaft from the hub and bearing on 4WD vehicles. Place a brass drift against the outer edge of the halfshaft to protect the shaft threads. Use a hammer to sharply strike the brass drift, but to do not remove the halfshaft at this time. Wheel speed sensor Wheel hub and bearing-to-steering knuckle bolts and hub and bearing


    Splash shield from the steering knuckle Seal from the hub and bearing

To install:
  1. Install or connect the following:

    Wheel hub and bearing seal Splash shield to the steering knuckle, making sure it-s properly aligned Hub and bearing to the steering knuckle, aligning the threaded holes Hub and bearing bolts and tighten to 77 ft. lbs. (105 Nm) Wheel speed sensor. Tighten the bolt to 13 ft. lbs. (18 Nm). Rotor and brake caliper Tire and wheel
    The Hub Bearing Torque - Front

    If Torque Specs are not in the box we recommend youtorque to this setting. Axle Nut: 103 Ft/Lbs.Flange Bolts: 77 Ft/Lbs. WARNING: Failure to observe the following warningscould create a risk of death or serious injury.Proper maintenance and handling practices arecritical.Always follow installation instructions and maintainproper lubrication.Every reasonable effort has been made to ensure theaccuracy of the information contained in thiswriting, but no liability is accepted for errors,omissions or for any other reason.This information is not intended to substitute forthe specific recommendations of your vehiclemanufacturer.Always use the recommended torque requirement unlessotherwise specified in the carton.Depending on the application, type of hub unitbearing and location, the installation process mayvary.Please review the vehicle manufacturer'srecommendation before removing or installingcomponents.
  2. Lower the vehicle
  3. On 4WD vehicles, install the drive axle nut and tighten to 103 ft. lbs. (140 Nm), then install the center cap.

Nov 10, 2012 | Cars & Trucks

1 Answer

2004 chevy aveo head torque espesc


you can get the torque specs from the dealer. if you replaced the valve cove gasket the just tighten the about the same as you would yor tire by hand not with a power tool!

Aug 04, 2010 | 2004 Chevrolet Aveo

1 Answer

Left front hub replacement 2WD.


2WD pickups don't have hubs. They have rotors with bearings. Once you have the brake assembly supported, remove nut from spindle. Be sure not to strip the threads on the spindle. Remove the front set of bearings and pull the rotor off. Remove the rear set of bearings. Be sure to pack greases into new bearings prior to installation. Insert new rear bearing into rotor and replace onto spindle. Insert new front bearing and washer and re-install nut. Tighten to recommended torque specs, grease fittings and replace brake assembly.

May 15, 2010 | 2005 Chevrolet Colorado

1 Answer

How do i change the driver side front hub assembly


The vehicle will need to raised on the left (drivers) side and supported. Remove the tire, then the brake caliper assy. Remove the rotor, then remove the axle nut located in the center of the hub assy. Remove the hub/bearing retaining bolts, and then the hub assy. Some times it is corroded into the steering knuckle assy. and will not seem to come out. If this happens, install the axle nut, and wearing safety glasses, pound onto the hub flange from the inside to the outside, until it comes out of the knuckle assy. Then remove the hub assy. Clean the knuckle hole where the bearing with 120 grit sand paper, so the hub/bearing assy will go into the knuckle without damage. Torque the axle nut to specs. Clean the inside of the rotor, where the hub meets it, so it sits flat against the new hub. Install the rotor, caliper assy. Install the wheel and torque the lug nuts to 100 ft pounds. Road test about 5 miles and recheck the lug nuts.

Jan 19, 2010 | 1998 Ford Explorer

1 Answer

What torque spec for chev aveo 2004 cylinder head


18 lb ft+60°+60°+60°+10°

NEW HEAD BOLTS ARE REQUIRED WHEN REPLACING THE HEAD OR HEAD GASKET.

Jul 04, 2009 | 2004 Chevrolet Aveo

2 Answers

Torque specs


the center bolt for cv axle!103ft-lbs,hub bearing assembly bolts!77ft-lbs

Apr 26, 2009 | Chevrolet Blazer Cars & Trucks

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,052 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...