Question about 2006 Dodge Sprinter

3 Answers

Remote key fob does not lock or unlock doors on a 2002 freightliner sprinter also the button on the console does not unlock or lock doors has to be done manualy any sugestions

Posted by on

  • Anonymous Sep 30, 2008

    I've been instructed that the fob and central locking system will become disabled once the fob has been pushed 200 times with out a response. This includes being out of the range of the reciever. The locking system/fob keeps track of each time this occures.

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Check the fuse dude it is by driver door side under driver seat.

Posted on May 11, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 512 Answers

Have central timer module checked. it is intregal to both fob and switch operation

Posted on Sep 24, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 137 Answers

You may have a dead remote battery. have it checked.

Posted on Jul 18, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key fob dont work, but door lock works ok, key fob battery change.


1. Get in your vehicle.
2. Close the door.
3. Put key in ignition
4. Do not turn on the ignition yet.
5. Hold down on the unlock button on the door panel. Do not let up.
6. Turn the key to ON, OFF, ON, OFF (while still holding the unlock button on the door panel).
7. Release the unlock button.
8. The door locks should cycle, indicating that you did everything correctly.
9. Have all your remote entry fobs available. Hold down on both the lock and unlock buttons until the door locks cycle. Do the same on all key fobs. This will re-program all of them.
10. Turn ON the ignition key to exit the program mode.
11. DONE.

Apr 18, 2014 | 1999 Chevrolet Silverado 1500

1 Answer

Replaced batery in key fob and now there is no connection between fob and security system...I can lock and unlock doors with the key and I can start car ...fob doesn't work; does not lock or unlock...


reprogram the remote transmitter. first leave driver door open all other doors closed,key removed from the ignition switch. insert key into the ignition switch,then remove it.press lock and unlock on the vechicle door lock control switch at 1 second intervals 5 times. close and repoen drivers door.press lock and unlock on the vechicle lock control switch at 1 second intervals 5 times. insert key into ignition switch. switch ignition on and off twice to program a remote transmitter code whilst erasing the original codes or three timre to check how many remote transmitters are currently registered.remove key from the ignition switch.system should now lock and unlock.twice to indicate programming mode or one to four times,slowly to indicate number of remote transmitters registered.for the solara press and hold lock and unlock remote buttons together, press lock remote button for a second period of 1 second. system should now lock and unlock vechicle.once to confirm, twice to indicate registration has failed.if required repeat button procedure to program remaining remote transmitters.note to exit programming mode close drivers door or insert ignition key.maximum of 4 remote transmitters can be programmed.if akk failed let dealership reprogram remote transmitters.

May 18, 2011 | 1999 Toyota Camry Solara

3 Answers

My Porsche Key fob no longer unlocks the doors


Insert key into door barrel or ignition lock and turn key, whilst doing this press the unlock/lock button, the led on the dash should flash to indicate this has initialised the key to the car, then remove key and test operation of remote. If this fails then a new remote plus coding to the car by your dealership is needed

Feb 16, 2010 | 2005 Porsche 911

1 Answer

My battery died on my key remote for my 2002 Ford Expedition. I have replaced the battery, but apparently need to reprogram it. How do I do this?


It should work even after taken the battery out., but here is the process.
1. place key in ing.
2.turn from position 2(lock) to pos 3(off), cycle pos 3 to pos 4, 8 times within 10 secs. your 8th turn ending in pos 4. Doors should lock/unlock confirming the program mode is ready.
3. within 20 secs, program your fob by pressing any button on the fob. the doors will lock/unlock confirm it is programmed. If more than 20 sec pass before pressing the fob button, the step will have to be redone.

Feb 05, 2010 | 2002 Ford Expedition

1 Answer

Need to reset the key fob after replacing the battery


You should not have to reset the key fob after a battery replacement. The signal from the key fob stays the same and is programed to the reciever.
If the key fob needs to be reprogrammed then follow these steps.
1. Have all key fobs with you during programming.
2. Sit in the vehicle with all doors closed.
3. Lock all doors using the Lock/Unlock switch on the door.
4. Insert and withdraw the ignition key 7 to 9 times within 10 seconds (do not turn the key, just insert and withdraw).
5. The 4 way flasher indicator on the dash should flash once or twice.
6. Insert the ignition key and turn it on (key on, engine off).
7. Press any button on one remote and the 4 way flasher indicator on the dash should flash once.
8. If you have more key fobs to program use the Lock/Unlock button on the door to unlock the doors and then lock the doors.
9. Press any button on the next key fob and the 4 way flasher indicator on the dash should flash once.
10. Repeat if you have more key fobs. Only 5 can be programmed.
11. To exit, simply turn of the igniton and remove the ignition key.
12. Unlock the doors using the Lock/Unlock switch on the door and exit the vehicle.
13. Make sure the window is down when testing remotes in case you leave the keys inside.
14. Close all doors and test all remotes that were programmed.

Do not skip any steps or the process will not work.

If the 4 way flasher indicator does not work when inserting the key, you will need to start the process from the begining. If it still does not work the receiver may be your problem.

If the 4 way flasher indicator does not flash when pressing any button on the key fob then the key fob is the problem (dead battery or defective remote)

Dec 18, 2009 | 2002 Nissan Xterra

1 Answer

How come on a 2002 GMC Denali if you lock your key inside


i would say the theft module saw the door trying to be open without the door lock or fob first, once the door lock button was pushed it shut down, it new doors were trying to be unlocked in a theft manner, once shut down it needs time to reset or needs to see ignition cycle with key and read chip in key, smart system isnt it, good luck.

Oct 21, 2009 | 2002 GMC Yukon Denali

4 Answers

Program a remote key for 03 A6


I have an A4 and did this to re-program my key:

1. used the key to start the car...then turned it off
2. put the key in the driver door (door closed)
3. pressed the lock button on the key fob once
4. turned the key to lock the door.

This is basically the steps in the owners manual, but the car must be started with the key first, and the key must be in the door lock before pressing the lock button.

Dec 10, 2008 | 2003 Audi A6

Not finding what you are looking for?
2006 Dodge Sprinter Logo

844 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...