Question about 1990 Volvo 740

1 Answer

1990 Vovlo 740 sedan - front seat replacement

How do I remove the front seat and what tools do I need? I can't find a service manual at the library for this and didn't want to purchase one just for this.

Thanks,
Bob

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

There's 4 bolts that hold it down, 2 in the front and 2 in the rear, and then there's 4 aligning pins that fit into holes. Wrench size is 13 mm I believe. The pins have a head on the bottom sort of like a nail, so you have to align the pins/heads just right, and the seat lifts right out. The head on the pin is about 3/4 inch. You have to disconnect the seat heater wire too, and if you have power seats you have to disconnect those wires also. I think on the power seats you take off the assembly on the side of the seat separately.

Posted on Jul 21, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm having trouble locating the starter on my 1990 volvo 740 gl. where is it located and how do i replace it?


As you are facing the car, it is on your right hand side - low on the engine - toward the rear of the car. To remove, 1) remove the positive battery cable 2) jack the drivers side front of the car up 3) from above or below, remove all electrical connectors

May 06, 2010 | 1990 Volvo 740

2 Answers

Repair and maintaines for volvo 740 GL


Chilton or Haines publishes manuals for the 740. Of the two, the Haines offers more direct parts removal and replacement info. The Chilton has too much generic filler. Get either on Ebay for less than $20.

Apr 08, 2010 | 1990 Volvo 740

1 Answer

'90 Volvo 740 2.3l turbo water pump install instructons needed


Go to an auto supply store like PEP boys or Advance Auto, etc., and buy a Haynes Repair Manual for the 740. You may be able to consult one at your local library for free. Even if it doesn't cover your model year, the replacement instructions are pretty much the same for all years. in fact even a 240 Volvo manual would be essentially the same. Pay particular attention to the installation instructions....you have to slide the pump on, and then rotate it a few degrees clockwise to make the upper o-ring seal. Good luck!

Nov 24, 2009 | 1990 Volvo 740

4 Answers

Firing diagram for 1990 caddy sedan deville front wheel 4.5?


To avoid confusion, remove and tag the spark plug wires one at a time, for replacement.
If a distributor is not keyed for installation with only one orientation, it could have been removed previously and rewired. The resultant wiring would hold the correct firing order, but could change the relative placement of the plug towers in relation to the engine. For this reason it is imperative that you label all wires before disconnecting any of them. Also, before removal, compare the current wiring with the accompanying illustrations. If the current wiring does not match, make notes in your book to reflect how your engine is wired.

55492de.jpg

4.5L and 4.9L EnginesEngine Firing Order: 1-8-4-3-6-5-7-2 Distributor Rotation: Counterclockwise

Hope helped with this (remember rated this help) Good luck.

Nov 10, 2009 | 1990 Cadillac SeVille

1 Answer

Need to replace the front drivers seat in a 1990 Nissan Skyline


easy.Remove the mounting bolts at the front and rear of the seat 2 front,,2 rear seat should just come out

Oct 23, 2009 | 1990 Nissan Maxima

2 Answers

RAN OUT OF GAS PUT 2 GALLONS IN TURNS OVER HOWEVER IT WONT START


Yes. All cars have fuel filters. The most common location is under the chassis by the fuel filler. Look for a little plastic cylinder with a pair of hoses going to it.

Regards,
matt

Sep 15, 2009 | 1990 Volvo 740

1 Answer

Removing Driver's seat in a 1991 Volvo 740


4 bolts is fairly easy remove the rear first with the seat all the way forwards and then put seat all the way back then 2 in the front remove them ..tilt the seat back and if there is any wire harness disconnect them as well ...reverse process for re-installation

Sep 07, 2009 | 1990 Volvo 760

1 Answer

I need to replace a rear seat belt in a 1997 Ford Tarsus. Does any know the best way to access the assembly? In addition, are there any diagrams available that show the connection points?


please don't forget to rate, thx.

Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Safety Belt Bolt Bit T77L-2100A
NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.

Removal
  1. Remove rear seat cushion. Refer to Section 01-10 .
Seat Cushion, Rear Sedan
Removal
  1. Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
  1. Remove rear seat cushion from vehicle.
  1. Remove rear seat back. Refer to Section 01-10 .
Seat Back, Rear 60/40 Split Bench—Sedan
Removal
  1. NOTE: Safety belt bolts do not secure seat back to vehicle.

    Remove rear seat cushion as described.
  1. Fold down back seat and remove two bolts in the center of each seat back striker plates.
  1. Remove two bolts from outboard rear seat back frame retaining brackets.
  1. Lift seat back up and pull forward to remove from vehicle.
  1. Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
Trim Panel, Quarter—Sedan Removal
  1. Remove rear seat. Refer to Section 01-10 .
  1. Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
  1. Pull lower quarter trim panel away from body.
  1. Remove safety belt retaining bolt.
  1. Feed safety belt through lower quarter trim panel.
  1. Remove safety belt anchor plate-to-sill bolt from quarter panel.
  1. Remove retractor anchor nut and retractor from rear quarter panel.
  1. Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
  1. Slide anchor plate end of safety belt through the openings in the quarter trim panel.
  1. Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.


    2a6fac0.gif


    Item Part Number Description 1 386277-S190 Bolt (Part of 611B68) 2 31012 Upper Rear Quarter Trim Panel 3 611B60 Retractor and Tongue 4 N800937-S190 Nut 5 389370-S190 Bolt 6 — Rear Quarter Panel (Part of Body) 7 52018 Lower Rear Quarter Trim Panel 8 — Mounting Stud (Part of Body)
  1. Remove seat belt anchor bolt and retractor and tongue from rear deck panel.


    fff90b0.gif

Installation
  1. To install, reverse Removal procedure.
  1. Make sure the safety belt webbing is not twisted. If it is, remove the twist.
  1. Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
  1. Check the restraint system for proper operation.

Jun 30, 2009 | 1997 Ford Taurus

1 Answer

Signal light


The front is quite easy. For the lens removal; there are two tabs, top and bottom, pinch them together and pull it out. Just push back in when finished. For the bulb; grab the wire leading to it at the end, and turn it counter-clockwise then pull it out.

Rear is tricky on the wagon, I don't know about the sedan, but I bet it isn't difficult. Very few things on these cars are.

Aug 31, 2008 | 1990 Volvo 740

Not finding what you are looking for?
1990 Volvo 740 Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volvo Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Mark Jones

Level 2 Expert

76 Answers

Are you a Volvo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...