Question about 1993 Audi 100

1 Answer

Timing - 1993 Audi 100

Posted by on

1 Answer

Dont get one

Posted on Aug 10, 2008


Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you adjust valves on a 2006 3.5L V6 Toyota Avalon?


There is a Toyota Technical Service Bulletin issued for this:-
T-SB-0291-08 September 11, 2008 2GR-FE Valve Timing

Procedure Service Category Engine/Hybrid System Section Engine Mechanical Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 - 2009 Avalon 2007 - 2009 Camry VDS(s): BK46K 2008 - 2009 Highlander 2006 - 2009 RAV4 Engine(s): 2GR VDS(s): BK31V, BK32V, BK33V, BK34V, ZK31V, ZK32V, ZK33V, ZK34V, ZK35V 2007 - 2009 Sienna Introduction This service bulletin provides information regarding valve timing inspection and service guidelines for vehicles equipped with 2GR-FE engines. © 2008 Toyota Motor Sales, USA Page 1 of 5 T-SB-0291-08 September 11, 2008 Page 2 of 5 2GR-FE Valve Timing Procedure Introduction (Continued) Figure 1. 3 2 1 5 9 8 7 6 4 1 RH Bank Intake Camshaft Timing Gear 2 RH Bank Exhaust Camshaft Timing Gear 3 RH Bank No. 2 Timing Chain 4 Crankshaft 5 Idler Gear 6 Timing Chain 7 LH Bank No. 2 Timing Chain 8 LH Bank Exhaust Camshaft Timing Gear 9 LH Bank Intake Camshaft Timing Gear Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 N/A Not Applicable to Warranty © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 3 of 5 2GR-FE Valve Timing Procedure Inspection 1. Set the No. 1 cylinder to TDC/compression. A. Set the timing mark to 0 on the timing chain cover by rotating the crankshaft clockwise. B. Verify the timing marks on the camshaft timing gears are in general alignment with the timing marks of the camshaft bearing cap: TIMING MARK IDENTIFICATION CYLINDER BANK INTAKE GEAR MARK EXHAUST GEAR MARK RH Bank (Bank 1) Small Mark Single Line LH Bank (Bank 2) Large Mark Double Line HINT When the engine is correctly timed, the timing marks will NOT perfectly align. Figure 2. Figure 3. RH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 4. RH Bank Intake Camshaft Timing Gear 2 1 1 Bearing Cap Timing Mark 2 Gear Timing Mark © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 4 of 5 2GR-FE Valve Timing Procedure Inspection (Continued) Figure 5. LH Bank Intake Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 6. LH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark HINT If the timing marks appear vastly out of alignment, turn the crankshaft one revolution (360 ) clockwise and note the position of the timing marks. Component Removal Guidelines 1. If engine disassembly is required that involves removing the camshafts or timing gears, set the #1 cylinder to TDC compression, wipe away any oil, and mark the following items in relation to each other prior to disassembly: • Timing gears • Timing chain • Timing chain No. 2 NOTE This relationship MUST be maintained. The intake gear is timed in relation to the crankshaft via the timing chain; the exhaust gear is timed in relation to the intake gear via the No. 2 timing chain. © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 5 of 5 2GR-FE Valve Timing Procedure Component Removal Guidelines (Continued) 2. If NEW camshaft timing gears or the No. 2 timing chain are being installed, the two yellow links on the No. 2 timing chain can be used to ensure correct relationship between the intake timing gear and the exhaust timing gear. Figure 7. 1 1 Yellow Link A. Align the paint mark on the timing chain with the intake gear timing mark (to ensure the intake gear is correctly timed to the crankshaft). Figure 8. RH Bank and LH Bank 3 3 4 3 3 4 5 4 5 4 1 2 1 RH Bank 2 LH Bank 3 Yellow Link 4 Gear Timing Mark 5 Timing Chain Paint Mark B. Align the two yellow links on the No. 2 timing chain to the timing marks on

May 04, 2015 | 2006 Toyota Avalon XLS

1 Answer

Noise in the timing chain


May be its problem with timing chain and it has to be inspected and replaced.Or its possible that timing chain is got misaligned.

There are few help,links provided related to timing chain assembly and dis-assembly. Go through it and confirm proper inspecting of timing chain.

Click the required help link below:----How to Replace Timing Chain Cover & Seal on Audi A4 ? http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-timing-chain-cover-seal.html
----------1982 Toyota Pickup: Set ignition timing, engine overheating, timing chain issue, dist off? http://whatisbyme.blogspot.in/2012/05/1982-toyota-pickup-set-ignition.html
----------How to Remove Timing Chain Cover and Seal on Toyota Previa?

http://technoanswers.blogspot.com/2011/12/how-to-remove-timing-chain-cover-and.html

--------


How to Remove Timing Chain and Gears on Toyota Previa?

http://technoanswers.blogspot.com/2011/12/how-to-remove-timing-chain-and-gears-on.html

-------


Ford Mondeo ST220 camshaft Timing specifications? http://technoanswers.blogspot.in/2012/02/ford-mondeo-st220-camshaft-timing.html
------------Replacing Timing Chain Cover For 2009 Ford?

http://repairhelpcenter.blogspot.in/2012/03/replacing-timing-chain-cover-ford-2009.html


-----------
Timing Chains & Front Cover Removal on 2008 Ford Taurus? http://repairhelpcenter.blogspot.in/2012/03/timing-chains-front-cover-removal-on.html
----------How to Replace Timing Chain Cover, Chain, Sprockets, & Seal On Ford Taurus? http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-timing-chain-cover-chain.html
---------How to Replace Timing Chain & Sprockets on Ford Windstar? http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-timing-chain-sprockets.html
---------Timing Chain & Sprockets Replacing on Ford, Mercury and Lincoln? http://fordrepairhelp.blogspot.in/2012/03/timing-chain-sprockets-replacing-on.html
----------How to Replace Timing Chain & Sprockets on Ford Edge and Lincoln MKX? http://howtobyme.blogspot.in/2012/03/how-to-replace-timing-chain-sprockets.html
------How To Replace Timing Chain, Sprockets & Front Cover on Ford Expedition and Lincoln Navigator? http://repairhelpcenter.blogspot.in/2012/03/how-to-replace-timing-chain-sprockets_356.html
---------Timing Chain, Sprockets, Front Cover & Seal removal for Ford Mustang? http://schematicsdiagram.blogspot.in/2012/03/timing-chain-sprockets-front-cover-seal.html
---------How to Replace Timing Chain on Buick LaCrosse? http://howtobyme.blogspot.in/2012/03/how-to-replace-timing-chain-on-buick.html
---------These details will help.For more help keep updated.Thanks.

Oct 15, 2012 | Cars & Trucks

1 Answer

Ichanged the head on my 91 geo storm 1.6 dohc and now it won't start


Double check crankshaft timing mark, on your lower timing cover has some timing marks - crankshaft should be on the 0 mark. Camshaft timing marks--intake camshaft mark set at 3 o'clock and exhaust camshaft mark set a 9 o'clock. These timing marks are critical for motor to run and start correctly. These timings marks can move while trying to install the timing belt. After, you confirm or reset timing and belt, you can confirm timing is correct by rotating the crankshaft twice. Your timing marks should be on right on timing marks discussed at the top of the page. If timing marks are off, start over with timing process.

Jul 11, 2012 | 1990 Geo Storm

1 Answer

How to Set Time on Mercedes-Benz A160


To set your time on an A160 follow the instructions below or follow the link to watch instruction video. http://youtu.be/nU3wtQ8A7Gc

How to Set Time on Mercedes-Benz A160

Adjusting the time:
Hold the time button pressed until the hour display flashes.
Adjust hours forward with the + button.
Adjust time backward with the - button.
Press the time button briefly. The minute will display will flash.
Adjust hours forward with the + button.
Adjust time backward with the - button.
Press the time button briefly and the newly set time is stored.

Jul 06, 2012 | Cars & Trucks

1 Answer

How do you fix timing on 96 nissan sentra


For adjusting the ignition timing, you need a timing light.
Attach the spark lead from the timing light to the number one spark plug.
If the timing light is a powered type then
Attach the power leads of the timing light to the battery - red lead to the + terminal on the battery and the black lead to the - terminal on the battery.

Loosen the distributor so you can adjust the timing, start the engine and press the timing light trigger and aim the timing light on the timing marks on the crankshaft pulley. Adjust the distributor to the recommended timing mark for your engine.
Turn off the engine, remove the timing gun and tighten the lock on the distributor.

Feb 24, 2012 | 1996 Nissan Sentra

2 Answers

Need for 2002 dodge stratus 2.7 timing chain diagram online


  1. Remove the timing belt.
    06009-sebr-g15.gif

    Crankshaft and camshaft timing marks-2.4L engine
    06009-sebr-g16.gif

    Timing belt tensioner-2.4L engine
    06009-sebr-g17.gif

    Camshaft sprocket alignment-2.4L engine
    06009-sebr-g18.gif

    Timing belt installation-2.4L engine
    06009-sebr-g19.gif

    Timing belt tension adjustment-2.4L engine
    06009-sebr-g20.gif

    Timing belt tension verification-2.4L engine

Dec 01, 2010 | 2002 Dodge Stratus

1 Answer

What is the right way to time a 4cyl Chevy S-10 timing chain


1998-2003 To Remove:
  1. Remove or disconnect the following:
    • Crankshaft pulley and hub
    • Drive belt tensioner gm_truck_s10_tcbolts.gif

    • Timing chain cover bolts gm_truck_s10_tc.gif

    • Timing chain cover and gasket
  2. Install a bolt in the end of the crankshaft CAUTION
    Do not install the crankshaft balancer bolt or a bolt longer than 1 inch or damage to the crankshaft threaded hole will result.
  3. Rotate crankshaft until the number 1 piston is at Top Dead Center of compression stroke.
  4. Make sure that the alignment marks are aligned with the tabs on the timing chain tensioner. gm-03-22-611.gif

  5. Measure distance between hole in bracket and unworn surface of timing chain tensioner shoe. NOTE: If distance between the hole and unworn surface of timing chain tensioner is greater than 0.314 in (8 mm), replace tensioner, timing chain and sprockets.
  6. Remove timing chain tensioner bolts.
  7. Remove the timing chain, timing chain tensioner and camshaft sprocket at the same time.
  8. Remove the crankshaft sprocket using special tool J 22888-20A or equivalent.
  9. Remove crankshaft sprocket alignment key.
gm-03-22-612.gif

NOTE: If any camshaft components are being replaced to correct a noise problem, all camshaft drive components must be replaced.
To Install:
  1. Install the crankshaft sprocket alignment key.
  2. Install the crankshaft sprocket using special tool J 5590 or equivalent. gm-03-22-613.gif

  3. Compress the timing chain tensioner spring and insert a pin into the tensioner hole to retain the tensioner shoe.
  4. Install timing chain and timing chain tensioner (do not tighten tension bolts).
  5. Align the crankshaft and camshaft timing marks with the tab on the timing chain tensioner.
  6. Tighten the timing chain tensioner bolts.
    • Torque to: 18 ft lbs (24 Nm)
  7. Tighten the camshaft sprocket bolt.
    • Torque to: 96 ft lbs (130 Nm)
  8. Remove pin from timing chain tensioner hole.
  9. Remove bolt from end of crankshaft. CAUTION
    Inspect the timing chain cover for warping or damage. Replace if needed.
  10. Clean all timing chain cover mating surfaces.
  11. Install or connect the following:
    • Timing chain cover to the engine block
      1. Ensure that the gasket is installed properly in the groove in the timing chain cover
    • Timing chain cover and make sure it fully seated on the alignment dowel pins
    • Timing chain cover bolts
      1. Torque to: 97 inch lbs (11 Nm)
    • Drive belt tensioner
    • Crankshaft damper hub and the crankshaft pulley

Aug 17, 2010 | 2000 Chevrolet S-10

1 Answer

My timing belt broke on my '99 Ford Escort ZX2. Please tell my husband how to replace it. Than k you



 
 
Timing Belt
REMOVAL & INSTALLATION
1.8L Engine
Disconnect the negative battery cable.
Remove the timing belt covers.
Rotate the crankshaft and align the timing marks located on the camshaft pulleys and the seal plate.
Remove the crankshaft pulley and hub.
If the timing belt is to be reused, mark an arrow on the belt to indicate its rotational direction to enable correct re-installation.
Loosen the timing belt tensioner lockbolt and remove the timing belt.
To install:
Temporarily secure the timing belt tensioner in the far left position with the spring fully extended, then tighten the lockbolt.
Make sure the timing marks on the timing belt pulley (crankshaft sprocket) and the engine block (oil pump housing) are aligned.
Make sure the timing marks on the camshaft pulleys and the seal plate are aligned.
Install the timing belt.
Loosen the tensioner lockbolt. Using a suitable prying tool, position the timing belt tensioner so the timing belt is taut, then tighten the tensioner lockbolt.
Turn the crankshaft two turns clockwise and align the timing belt pulley mark with the mark on the engine block.
Fig. 1: Timing marks are located on the camshaft pulleys as shown — 1.8L engines


 
Fig. 2: Make sure that the crankshaft sprocket (timing belt pulley) and oil pump timing marks are aligned — 1.8L engines


 
Fig. 3: Align the timing belt pulley mark with the tension set mark, at approximately the 10 o'clock position — 1.8L engines


 
Fig. 4: Check the timing belt deflection at the location shown — 1.8L engines

Mar 28, 2009 | 1999 Ford Escort

2 Answers

Timing specs


Here is All Lititure But Pictures Wont show up on FixYa for some reason, I can Email it ALL to you Just Send Me A Request to my Nickname here @aol.com


SPECIAL TOOLS REQUIRED (or equivalents)
  • J-36008, Camshaft sprocket timing alignment pins.
  • J-39579, Camshaft sprocket wrench.
CAUTIONS:
  • The timing chain on the 1996 LD9 (VIN T) Twin Cam Engine is not to be replaced with the timing chain from any other model year. The timing sprockets are different on the Twin Cam Engine and the shape of the links matches the sprockets. Engine damage may result if the wrong timing chain is used.
  • The timing chain and crankshaft sprocket MUST be marked so that they are reinstalled with the same side facing out at the time of reassembly.
  • Failure to follow the removal and installation procedures could result in severe engine damage.
REMOVE OR DISCONNECT
  1. Negative battery cable.
  2. Front cover, refer to Timing Cover / Service and Repair .
  3. Rotate crankshaft in clockwise direction until camshaft and crankshaft timing marks are aligned.
  4. Timing chain guides.
  5. Raise and support vehicle.
  6. Ensure slack in timing chain is above tensioner assembly, then remove chain tensioner. The timing chain must be disengaged from grooves in tensioner shoe to permit removal of shoe. Position a suitable screwdriver under timing chain while pulling shoe outward. If difficulty is encountered in removing tensioner shoe, proceed as follows:
    1. Lower vehicle, then while holding the intake camshaft sprocket with J-39579, remove sprocket bolt and washer.
    2. Remove washer, then install bolt into camshaft by hand.
    3. Position a suitable three jaw puller into intake camshaft sprocket relief holes and remove sprocket. CAUTION: Do NOT pry on camshaft sprocket as damage to sprocket or timing chain housing may result.
  1. Tensioner assembly attaching bolts and tensioner assembly.
  2. MARK CRANKSHAFT SPROCKET AND TIMING CHAIN outer surface for reassembly.
  3. Timing chain.
INSTALL OR CONNECT
  1. Intake camshaft sprocket onto camshaft with surface marked during removal showing.
  2. Intake camshaft sprocket retaining bolt and washer, torque to 70 Nm (52 ft lbs) while holding the sprocket with J-39579 (if removed).
  3. Timing pins, J-36008, through holes in camshaft sprockets into holes in timing chain housing to position camshafts for proper timing. If camshafts are out of position and must be rotated more that 1/8 turn to insert timing pins:
    1. Crankshaft MUST be rotated 90°clockwise off of TDC in order to give the valves adequate clearance to open.
    2. Once the camshafts are in position and the timing pins have been installed rotate crankshaft COUNTERCLOCKWISE to TDC. CAUTION: Do NOT rotate the crankshaft clockwise to TDC, valve or piston damage could occur.
  1. Timing chain over exhaust camshaft sprocket, around idler sprocket and around crankshaft sprocket.
  2. Set camshaft sprockets at timed position and install timing chain. Remove timing pin from intake camshaft. Using J-39579, rotate the intake camshaft sprocket counterclockwise until timing chain can be installed over sprocket. Release J-39579 after timing chain has been installed over sprocket. The length of chain between intake and exhaust camshaft sprockets should tighten. The timing pin should easily fit through intake camshaft sprocket timing hole into timing chain housing timing hole. If timing pin does not fully index, the camshafts are NOT timed correctly and the procedure MUST be repeated.
  3. With timing pins installed, raise and support vehicle.
  4. With slack removed from timing chain between intake camshaft sprocket and crankshaft sprocket, timing marks on crankshaft and engine block should be aligned. If the marks are not aligned, move timing chain one tooth forward or rearward to align marks. Remove slack and recheck marks.
  5. Reload tensioner assembly to zero position as follows:
    1. Form a keeper out of heavy gauge wire into a U-shaped piece with a half inch opening.
    2. Apply slight force on tensioner blade to compress plunger.
    3. Insert small screwdriver into reset access hole and pry rachet pawl away from ratchet teeth while forcing the plunger completely in the hole.
    4. Install keeper between access hole and blade.
  1. Tensioner assembly to chain housing and recheck plunger assembly installation, noting long end is toward crankshaft.
  2. Tighten timing chain tensioner bolts to 10 Nm (89 in lbs) .
  3. Lower vehicle to point where timing pins can be removed from camshaft sprockets.
  4. Rotate crankshaft two revolutions in the clockwise direction. Align crankshaft keyway with the mark on cylinder block and reinstall timing pins through camshaft sprockets into housing timing holes. Timing pins should slide easily through timing holes. If timing pins cannot be inserted easily, repeat procedure to properly time engine. CAUTION: If the engine is not correctly timed, severe engine damage could occur.
  5. Timing chain guides.
  6. Engine front cover.
  7. Negative battery cable.

Nov 15, 2008 | 1995 Pontiac Grand Am

Not finding what you are looking for?
1993 Audi 100 Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60769 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

13152 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...