Question about 1987 Chevrolet G10

1 Answer

Bypasing ignition i broke my key off in the ignition and want to know pretty much how to hot wire it till i can replace the whole ignition assembly and door locks

Posted by on

  • j_man0232003 Jul 17, 2008

    thank you very much darklord. this information was very helpful and i appreciate it

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,427 Answers

Http://www.ehow.com/how_2044915_hotwire-car.html

Hotwiring is used inilligal activities but in your case i dont have a problem in showing you how its done.

1.) Remove the part of the dash covering your ignition key assembly
2.) There should be 5 to 8 wires there
3.) Locate 2 wires of similar color
4.) strip these wires and tie then together this will turn on the ignition
5.) find the starter wire usually blue and touch it to these wires, Imidately remove it when the car has started.
6.) tape them up

If your wireing is a bit different or you dont have similar color wires then
use steps 1 and 2 from above
3.) locate the the on positive wire
4.) run a wire grom the negative battery pole to the on positive wire. (U can strip each wire there and ground it to the wire from the battery pole , the correct one will turn the ignition on.
5.) once located tie it to the ground.
6.) touch each one of the expose wires one by one until the car tumbles and starts.

If you are still having trouble use this link
http://www.ehow.com/how_2044915_hotwire-car.html

Posted on Jul 17, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Everything works it just wont turn over


You probably have a bad ignition switch on the column. Dodge trucks have a wonky aspect to the ignition key switch. My Ram does the same thing. While parked, put the key in and try to wiggle the whole ignition cylinder. If it even wiggles slightly, the switch assembly (on the left side of the column, under the plastic) is probably your problem. You can buy aftermarket replacements for about 50 bucks. Pretty easy to replace. Youtube has a couple videos on how it's done.

Feb 27, 2016 | 2005 Dodge Ram 1500

1 Answer

Broke ignition key need to know how replace ignition


They make small lock picks with little hook on the end you can pull the broken key out with .I have seen them on ebay pretty cheap.

Jul 10, 2012 | 1983 Chevrolet Camaro

2 Answers

I have to replace a ignition cylinder switch on a ford zx2 escort key is broke off in the ignition and want turn even with the other haft of the key


Sounds like you will need to replace your ignition key switch.Recommending a used one at local auto wreckers most inexpensive route to go.

Dec 19, 2010 | 2001 Ford Escort ZX2

1 Answer

1996 Nissan 200SX Manual. Ignition Lock Assembly


You have solved your own problem. I have replace many of these units. It is much simpler to carry and extra key than to screw arround with the old lock assembly. Keys and tumblers ware out like everything else. Let me know if I can help[

Jun 19, 2010 | 1996 Nissan 200SX

1 Answer

2007 cobalt will not start or turn over. key


Could be a problem with key in ignition switch located on the side of the lock cylinder inside steering column. The one I worked on this was part of whats called clockspring assembly witch will be a dealer only part. Then you cut the two wire swtch off and splice it in so you don't have to remove steering wheel and replace the whole clockspring assembly. Might also be problem with ignition switch (inside column) that key lock cylinder ingages into. I have a couple of questions. Is power going to the dash and just not the starter? Is the security light on all the time and dosn't cycle out? There should be a anti theft reset precedure like leaving key on till light goes out. Good luck hope this helped

Apr 22, 2010 | 2007 Chevrolet Cobalt Coupe

2 Answers

Cae was stolen and recovered. they broke the ignition. how do I replace the steering column Is it necessary to replace the entire column?


Hi,

I am sure this would work by just replacing the ignition switch, not the entire steering column.

However it also depends on how bad was it broken.

Please let us know for future assistance.
Thanks
Fame !

Jul 10, 2009 | 1997 Dodge Intrepid

1 Answer

1991 Toyota Camry door locks


I would replace the whole assembly for the ignition Its pretty simple. Just take apart the steering column and find the screws that hold it in and the pin and slide it out and make sure you plug all the right wires back in. That way you only pay for the ignition. You may have to get new keys with that also. Or go to a junk yard and find one with maybe the keys still in it and take that one at so if you do brake something it ain't yours yet and so you know how to take it out for yours. Well hope that helps.

May 03, 2009 | 1991 Toyota Camry

1 Answer

Ingnition tumbler broke cant start


If the key won't start it; it might not be the key ignition, but rather; the ignition that has a stem that goes from the key ignition down on the steering colunm. However, you can get key ignitions for them, or buy the whole steering colum then take the key ignition out of it. But, I would suggest more information is needed before I can conclude that it is just the key ignition. Hope this help~!

Jan 19, 2009 | 1990 Plymouth Grand Voyager

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

248 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...