Question about 2001 Lexus LS 430

1 Answer

Passenger side door mirror

Door mirror case was damaged. Have replacement and need to know how to remove old and replace with new.

Posted by on

  • Anonymous Mar 21, 2014

    REPLACE SIDE VIEW MIRROR

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 1,986 Answers

On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Then you'll need to manipulate the panel and disconnect the door handle linkage from the door handle and disconnect the wiring for your controls. Then you can access the bolts that secure the mirror onto the door

Posted on Sep 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Driver side mirror replacement


Instructions1.
    • 1
Remove thedoor panel. Refer to your Honda Accord repair manual for theinstructions in removing the door panel. Unhook the rods and connectors on theinside of the door panel and set it on the floor.
    • 2
Remove thefilm covering the access to the side mirror. It's difficult to avoid damaging thefilm while removing it so you will need to purchase a new piece of filmcovering when you buy a new side view mirror.
    • 3
Reachthrough the service hole into the mirror housing with a screwdriver. Loosen thescrew that holds the mirror. Twist the screw out with your hand.
    • 4
Reacharound the door and support the mirror with your other hand. Continue to twistthe screw out, then catch the mirror as it drops out when you remove the screwcompletely. Put the screw in a safe place so you don't lose it.
    • 5
Installthe new side view mirror by positioning it where the old mirror was. Insert thescrew you took out in Step 4 and twist it in with your hand. Insert ascrewdriver into the service hole to tighten the screw.
    • 6
Replacethe film covering that was damaged when you took out the old mirror. Push itinto place in the indentation on the door.
    • 7
Sit in thecar seat and adjust the mirror so you can use it properly.

Jul 06, 2012 | 2005 Honda Accord

1 Answer

I need to replace my audi a6 driver side mirror? I have the new one and i'm trying to take off the old one, but i don't want to damage anything. How do i remove the old one?


Hi,to remove it the door panel needs to come of and then the cover on in side of door at side of mirror there will be screws there for the mirror.hope this helps

Jul 20, 2011 | 2004 Audi A4

1 Answer

Do you need to remove the passenger side door panel to replace the outside mirror?


if the car has power mirrors then yes you have to remove the door panel to get access to the plug end to unplug the old mirror and install the new one. hope this helps

Jan 09, 2011 | 2004 Chevrolet Impala

1 Answer

Looking to replace passenger side mirror on a 2006 Town and Country. Anyone have Instructions available?


    Remove Old Mirror
  1. 1 Open the side door to the Chrysler Town & Country, and find thescrew that holds the side mirror molding in place.

  2. Take the screw out and remove the molding panel that attached around the outside of the power mirror.

  3. Remove the bolts connecting the mirror to the door assembly. If equipped, unplug the power side view mirror wiring harness connector.

  4. Unplug the electric connectors, and pull the mirror out of the molding.

Jun 01, 2010 | 2006 Chrysler Town & Country

1 Answer

Im trying to replace the passenger mirror, need to


On the inside trim, you can remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. Once the panel is off, you will see two or three bolts securing the mirror assembly onto the door

Sep 21, 2009 | 2003 Chevrolet Venture Passanger

2 Answers

Need to replace Mirror Assembly, 03 suburban


Your going to have to remove the inside door panel to get to the three bolts that hold the out side mirror assembly. Once you have the door panel off you'll see the three bolts that hold the mirror assembly, just un-bolt and un-clip the wire harness to the electric/heated mirror. To install the new mirror assembly, just do everything in reveres. Go to Auto Zone and by extra door panel clips, there is a good chance of breaking some of the retainer clips and Auto Zone will have the step by step instructions to replacing the mirror assembly and the removal to the door panel. Good luck and keep me posted. Be glad to help.

Jun 22, 2009 | 2001 Chevrolet Suburban

1 Answer

Passenger side mirror replacement procedures


If its a power mirror there is more thing you will have to remove to get to the wires but if not there is a screw on the corner piece on the inside of the door. just pull the screw out and the bolts (3) that hold the mirror on are behind it. If it power then you will have to remove the door panel to access the wiring to disconnect it

Jun 21, 2009 | Ford Taurus Cars & Trucks

1 Answer

2008 Ford Fusion Wing Mirror Replacement


I checked Ford Focus mirror replacement and it seems to be the same. This is for the manual, unheated mirror.

Remove the mirror cover inside the door - slide a screwdriver behind the cover and pry loose carefully.

Remove the single 10mm bolt and the mirror comes free.
NB. Do not drop the bolt into the door.

Apr 02, 2009 | 2008 Ford Fusion

1 Answer

Replacing Nissan Altima 1998 passenger mirror


to replace it you have to open up the door take off the little plactic piece in the corner of the door,, then there is going to be 3 screws that you have to remove in order to remove the old one, just do the steps in reverse to replace the new mirror, i just had the same issue, but on the driver side.. good luck

Mar 18, 2009 | 1998 Nissan Altima

2 Answers

Instructions for replacement of side view mirror


the door panel near the mirror must be removed if not the entire door panel inside u will find 3 nuts to remove to get the old mirror off. hope this helps please rate me

Jan 12, 2009 | Pontiac Grand Prix Cars & Trucks

Not finding what you are looking for?
2001 Lexus LS 430 Logo

468 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...