Question about 2007 Dodge Caravan SXT Minivan New Cars

3 Answers

Remote keyless entry

I have a dodge grand caravan 2007 and have a new key but need the
procedure to program same have one working remote.

Posted by on

  • heshoh Jan 17, 2009

    How can i programer 2005 Dodge Grand Carvan remote

×

3 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 85 Answers

“CUSTOMER LEARN” MODE This feature is only available on domestic vehicles or those which have a U.S. country code designator. This procedure requires access to at least two valid Sentry Keys. If two valid Sentry Keys are not available, Sentry Key programming will require the use of a scan tool.
The steps required to program Sentry Keys with two valid Sentry Keys follows:
1. Obtain the blank Sentry Key(s) that need to be programmed. Cut the keys to match the ignition lock cylinder mechanical key codes. 2. Insert one of the two valid Sentry Keys into the ignition switch and turn the ignition switch to the ON position. 3. After the ignition switch has been in the ON position for longer than three seconds, but no more than fifteen seconds, cycle the ignition switch back to the OFF position. Replace the first valid Sentry Key in the ignition lock cylinder with the second valid Sentry Key and turn the ignition switch back to the ON position. The second valid Sentry Key must be inserted within 15 seconds of removing the first valid Sentry key. 4. About ten seconds after the completion of Step #3 , the indicator light will start to flash and a single audible chime tone will sound to indicate that the system has entered the "Customer Learn" programming mode. 5. Within sixty seconds of entering the "Customer Learn" programming mode, turn the ignition switch to the OFF position, replace the valid Sentry Key with a blank Sentry Key transponder, and turn the ignition switch back to the ON position. 6. About ten seconds after the completion of Step #5 , a single audible chime tone will sound and the indicator light will stop flashing and stay on solid for three seconds and then turn off to indicate that the blank Sentry Key has been successfully programmed. The SKREES will immediately exit the "Customer Learn" programming mode and the vehicle may be started using the newly programmed Sentry Key.

NOTE: The Remote Keyless Entry (RKE) Transmitter will also be programmed during this procedure. These steps must be completed in their entirety for each additional Sentry Key to be programmed. If any of the above steps are not completed in the given sequence, or within the allotted time, the SKREES will exit the "Customer Learn" programming mode and the programming will be unsuccessful. The SKREES will also automatically exit the "Customer Learn" programming mode if:

  1. It sees a non-blank Sentry Key when it should see a blank.
  2. If it has already programmed four (4) valid Sentry Keys.
  3. If the ignition switch is turned to the OFF position for more than about fifty (50) seconds.

NOTE: If you attempt to start the vehicle while in “Customer Learn” mode (LED flashing), the vehicle will behave as though an invalid key is being used (i.e. the engine will stall after two (2) seconds of running). No faults will be logged.
NOTE: Once a Sentry Key has been programmed to a particular vehicle, it cannot be used on any other vehicle.

Posted on Aug 05, 2008

Same problem (only one key) w a used '06 I just purchased.   The dealer wants $140.00 for a new key, but ebay has the key for ~$64.00, I guess I'll have to pay the dealer to scan/reprogram everything.   

Posted on Oct 17, 2008

I was told the only way is to have the dealer program it. Mine was $150. for the key and another $50. for programming. Ouch!

Posted on Jul 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Both my keys FOBs on my 2000 Dodge Grand Caravan don't work, changed the batteries, still did not work. Bought 2 new ones and the dealer could not program them.


Programming a Replacement Keyless Entry Remote ' Filear ...

filear.com/?p=131
Oct 17, 2012 - If the transmitters don't work, or if you'd rather not match the transmitters yourself, .... Tried these instructions last night on my 2005 Grand Prix.

Key FOB Not Working - The Chrysler Minivan Fan Club Forums

forum.chryslerminivan.net/showthread.../11859-Key-FOB-Not-Working

Mar 15, 2009 - 10 posts - ‎3 authors
Hi Everyone, One of my Key FOB's stopped working. Is there a way of ... Well, to be honest, you don't know where that FOB has been? LOL ... 2009 Dodge Grand CaravanSXT (3.8L), Light Sandstone Metallic, 125K miles 2005 Volvo .... By jimmy154 in forum 3rd Generation Chrysler Minivans: 1996-2000.

Key May Not Start Car or Release From Ignition : Dodge ...

repairpal.com > Problems > Dodge > Grand Caravan
Dodge Grand Caravan Key May Not Start Car or Release From Ignition. ... If the newkey doesn't work, replacing the lock cylinder including tumblers ... I am able to turn off the van, but the key is stuck in the ACC position, draining my battery. ... In reading other comments, I see it may be the FOB so I'll carry both with me and ...

2009 Dodge Grand Caravan car lock doors not working


Jan 24, 2016 | 2000 Dodge Grand Caravan

1 Answer

Como reiniciar motor con bad key?


PDF]Download 2014 Dodge Grand Caravan Owner's Manual

www.dodge.com/download/pdf/.../2014-Grand_Caravan-OM-2nd.p... DodgeIt also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry

Aug 05, 2015 | 2008 Dodge Grand Caravan

2 Answers

Can i disconnect the anti theft on a 2005 dodge grand caravan


You can not disable this system. The powertrain control module (PCM) programmed look for the Transponder Key (your ignition key has micro chip code). You will have replace your ignition switch and get new key reflashed by a dealer or locksmith

Mar 13, 2015 | 2005 Dodge Caravan

1 Answer

I locked my vehicle (2008 Dodge Grand Caravan), with the remote keyless entry fob. The keyless entry will not unlock the doors, even after I replaced the battery. Unfortunately the emergency key that is...


It sounds like your FOB needs to be reprogrammed, email me at bigt_wlm@juno.com around thursday and I will try to email you the programming instructions for that, If I am not able to you will need to call a locksmith with a T-Code or MVP Pro key programmer or DODge to programm your remote to your ECU

Oct 31, 2010 | Dodge Grand Caravan Cars & Trucks

1 Answer

Keyless remote stopped working, I replaced battery


The 1997 to 2003 Dodge Caravan and Grand Caravan use a standard key and remote setup with a separate remote fob. However, the 2004 to 2009 Dodge Caravan and Grand Caravan use a combination key and remote on one device. To program a new keyless entry remote for the 1997 to 2003 Dodge Caravan, you must have at least one functional remote, which is required to enter synchronization mode. To program the combination key for the 2004 to 2009 Dodge Caravan, you must have two functional combination keys. If you do not, you'll need to see an authorized Dodge dealer for keyless entry programming assistance.


2004 to 2009 Caravan Programming Instructions
  1. Insert one of your working combination keys into the ignition. Turn it to "On"; leave it in this position for about 10 seconds but no longer than 15 seconds. Turn it to "Off" and remove it.
  2. Insert your second working combination key into the ignition within 15 seconds of removing the previous key. Turn it to "On". After 10 seconds, you'll hear a chime and the "Theft" light will begin to flash, entering synchronization mode. Turn the key to "Off" and remove it.
  3. Insert the combination key you want to program. Turn it to "On." After 10 seconds, you'll hear a chime; then the "Theft" light will turn off. When the light turns off, the combination key--including the key and the remote--is programmed.
  4. Repeat Step Three for each combination key you want to program. A total of eight can be programmed.
Hope this help (remember comment and rated).


May 08, 2010 | 2008 Dodge Grand Caravan

1 Answer

How do i program a new keyless entry remote to work on my 98 dodge caravan


1999 dodge durango keyless entry dont work . i replaced the baturys still dont work . is thair a way to reprogram it with out a nother remote

Apr 29, 2009 | Dodge Caravan Cars & Trucks

1 Answer

New key?


The dealership can use the vin number to make you another key. You shouldn't have to have the keyless remote key. You can get a regular key.

Jan 22, 2009 | 2007 Dodge Grand Caravan SXT Minivan

Not finding what you are looking for?
2007 Dodge Caravan SXT Minivan New Cars Logo

3,303 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...