Question about BMW 318

Open Question

27bb cam control function exhaust on bmw - 318 BMW Cars & Trucks

Posted by on

  • Anonymous Apr 20, 2009

    anyone got any info on this problem?

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What does this codes means 2781 & 277f & 2782 & 27BB


You need to read the standard OBD2 codes, use a code reader and read the codes at the diagnostic port under the dash. OBD codes start with a "P" then four numbers 0-9

May 25, 2016 | BMW Cars & Trucks

2 Answers

How to fix 2002 BMW M3 service code 11360212. The code says solenoid valve for camshaft adjusting unit Permanent failure. What part needs to be replaced or repaired?


the problem will be in the unit that is attached to the end of the cam shaft that is driven by the timing belt/chain. It is hydraulically controlled by a solenoid that gets the signal from the ECM. Replacement of the unit by an accredited specialist will be the fix.
The unit changes the valve timing by advancing or retarding the cam shaft in accordance to engine RPM

Jan 15, 2015 | 2002 BMW M3

2 Answers

Why is my1997 bmw Z3 1.9 start rough for 2min then is ok


The EGR valve opens when the engine is warming up, which allows exhaust to enter the intake manifold. This is essentially "extra air" coming into the engine. The engine has an "idle speed control" function, which is either a solenoid or small stepper motor connected to a valve that allows a controlled amount of air to "sneak" by the throttle plate in the throttle body. Fundamentally, it is the amount of air entering a fuel injected engine that controls engine RPM. A defective idle speed control ("ISC) motor or solenoid can cause the problem you stated. (I do not know which type is used in your BMW.) Often, a check engine light will illuminate of the engine computer cannot adequately regualte engine idle speed.

Aug 27, 2014 | 1997 BMW Z3 Roadster

1 Answer

1995 BMW 525i 6cyl How many oxygen sensors does it have? And location of them?


It has four. The first two are called the pre-cat (catalyst) or hot side. They are located under the hood on the left side (when standing at the front looking at the motor) on the exhaust manifold. The other two or called the post-cat or cold side. They are in the exhaust pipes coming down from the motor under the car at the passenger side. Replace them with genuine Bmw parts. They are more expensive but you won't have any issues. A lot of problems come from aftermarket sensors because the calibrations aren't the exact same.

Jul 22, 2014 | 1995 BMW 525i Sport

1 Answer

Cam sensor


The Cam sensor is used for fuel control you have cam position sensor one on the exhaust and one for the intake.The use of a cam sensor improves mixture for each individual cylinder the advantages are gained independly supplied with fuel

Mar 01, 2012 | BMW X7 Series Cars & Trucks

1 Answer

Need to find the loction of camshaft position sensor for BMW 325I


need more info. size of engine and year. You have an exhaust sensor and a intake if you have duel variable cams. The exhaust is located in front towards the top inbetween the radiator cap area on the engine. The intake is located on the intake side about where #1 cylinder is under the intake. Your going to most likely have to move the oil filter housing and the cam position motor out tof the way to access. Only replace the part with a dealer part. If you don't and the light does not go off you will be kicking yourself because you won't know if it was because of a inferior part. I went thru this with my 2000 528i

Aug 09, 2010 | BMW 325 Cars & Trucks

1 Answer

I have a 01 325 bmw- runs great, however, the service engine light has stayed on continuously. Car was placed on diagnostic computer. I was told that I need cam-shaft exhaust replaced- this is what showed...


I need moe information than just the exhaust cam shaft needs to be replaced, it it's a twin cam I want to know how they determined it was the exhaust cam and not the intake, either can cause fuel mixture to be off to make the check engine light on Unless its is a common problem and a recall on this car. Before I would replace cam I would do a dry and wet compression check to verify that it's the valves. and if the cam needs to be replaced then you need to do both plus the valves. and guide seals as well, even gide seals on the intake could cause faulty reading so if there was no compression test the information is inconclusive more test procedures need to be done before tear down also does it have a rubo? and is it gas or diesel? I need this information to to diagnose properly. Or to narrow it down..

Dec 23, 2009 | 2001 BMW 325

1 Answer

Timing mark alignment for 92 bmw 325i 2.5L how do I align these sprockets. the ones on the exhaust cam are somewhat adjustable.


your cams have a what looks like a square on them . find it and face them with the dimples on them up. then use a flat edged ruler to make sur you have them right. then turn no.1 cylinder top dead center. then take and put your chain on your exhaust sprocket and point the dimple up do the same with the intake. tighten down the torx bolts and recheck! it took me 3 times but its better than the $300+ tools and car runs great. if need be look up some of the e36 groups on line.

Oct 20, 2009 | BMW 325 Cars & Trucks

1 Answer

1999 BMW 528i exhaust camshaft sensor code


Had the same problem on one.Ended up having to replace the intake cam sensor to cure problem.BMW recomends replacing both at the same time.

Aug 05, 2009 | BMW 528 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

427 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Fred Sops

Level 2 Expert

271 Answers

Al Clark

Level 2 Expert

290 Answers

Doberman

Level 2 Expert

246 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...