Question about 1999 Plymouth Voyager

1 Answer

1999 plymouth voyager brakes

I have replaced the master cylinder and front pads & rotors . I bled the system well, and have great brakes for about three days, then the peddle gets spungey. I then have to bleed them again to get a couple of days out it, before it happens again. Im on my third master cylinder please help

Posted by on

  • Anonymous Mar 24, 2014

    brakes were recently changed and failed after a few days

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 48 Answers

The master cylinder needs to be "bench-bled" before installation, if you are doing this and still having the problem, did you look into changing the rear brakes as well? check rear wheel cylinders for any small leaks

Posted on Jul 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brakes r going to the floor after let the system change the master cylinder and the power booster for a 1999 Plymouth Grand Voyager


Brake system must be purged/ bled of air when system is opened. Some times the entire system has to be bled several times to get ALL of the air out. Please refer to a repair manual for correct bleeding procedure or take vehicle to reputable mechanic. Brakes save lives!!!

Mar 21, 2014 | Cars & Trucks

1 Answer

No brake pressure


When you bled the system was fluid coming out the bleeder valves?
Where the bleeder valves closed off with the brake pedal fully depressed?
Is the fluid reservoir cap ok?
Is the master cylinder ok?

Jan 05, 2014 | 1995 Chevrolet Cavalier

1 Answer

1999 Ford E350 van problem: brake pedal is soft; have replaced master cylinder, rear wheel cylinders, rear brake shoes and drums, front calipers, rotors and discs; have bled master cylinder before...


Good question, on the antilock system is a bleader too and bleade it the same way you bleade the caliper. After all is done adjust the rear brakes, they should have a drag to them.

Feb 23, 2011 | 2007 Ford E-350 Super Duty Length XLT

3 Answers

Brake on front passenger side continuously locks up (seizes). Have replaced the master cylinder, rotor, pads and caliper but problem persists. System was bled entirely and new brake fluid flushed througout...


Replace the brake hose. An internal tear in the hose can allow fluid to flow into the caliper, but collapse inside not allowing the pressure to release.

Jan 29, 2011 | 1999 Ford Taurus

1 Answer

2000 PLYMOUTH GRAND VOYAGER BRAKE SMOKING. IVE CHANGED ROTOR,PADS,CALIPER AND BLED THE BRAKES. AFTER DRIVING FOR A WHILE THE BRAKES START SMOKING FROM NOT RELEASING.


possible the master cylinder is not allowing the brakes to release all the way. also did you check the slider bolts on the brakes to make sure there not binding? if there new or all the brakes are smoking i would lean towards the master cylinder

Jan 21, 2011 | 2000 Plymouth Grand Voyager

1 Answer

Front brakes are locking & seizing up. Put New brake pads, new rotors, new calipers, new hoses, new wheel right master cylinder.


Hello, wow sounds like you have done it all. But there is a spliter block that is right below the master cylinder that the two lines from the master cylinder goes into and then four other lines come out of it going to each wheel. Not often but sometimes these will cause that problem. Good luck

Jan 18, 2011 | 1998 Plymouth Voyager

1 Answer

Having trouble bleeding brakes on 1997 olds bravada. bled all four still pedal goes to floor. any suggestions?


Are the rotors worn? Worn rotors and new pads will sometimes cause this. The pad sits across the ridges and no matter how much you bleed the system the pedal just wont stiffen up. (See diagram. A - New pads, B - Rotor, C - Ridge)
If you did not install new pads you may also want to check the master cylinder seals. First bleed the system at the pipes that connect to the master. If the rotors are ok, you've bled the master cylinder and the problem persists then replace the seals or the complete master cylinder.


868a25e.jpg

Aug 18, 2010 | 1997 Oldsmobile Bravada

1 Answer

Pistons in both front calipers stay out, both calipers replaced


You may have a leak in the booster or master cylinder. You can put a pressure tester on the system to test for leaks. It does sound like you have an air leak.
You can try to bleed the master cylinder, then slave cylinder, then brake lines.

Aug 24, 2009 | 1993 Oldsmobile Achieva

3 Answers

Brakes are still spongy after changing the pads, one caliper, and master cylinder. bled front brakes.


I just went to Brake Masters this morning and had them replace the Master Cylinder since I was experiencing the pedal very spongy and going to the floor. When they replaced the Master Cylinder and they gave me back the car, the brakes were still spongy and going to the floor. I addressed this to them and they took another look at it, but when I took it for a second time, the brakes were extremely spongy. It was almost like they gave me back my car in worst condition to when I brought it in. Can you help?

May 21, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

1993 voyager 3.3 bake & abs light on - very hard pedal


Your Brake Master Cylinder is Failing. Get this Replaced and the Brake System Bled and it will work just fine. Please Rate My Response! Thanks!

Feb 03, 2009 | 1993 Plymouth Voyager

Not finding what you are looking for?
1999 Plymouth Voyager Logo

301 people viewed this question

Ask a Question

Usually answered in minutes!

Top Plymouth Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...