Question about 1988 Chevrolet C/K 3500

1 Answer

My 1989 chevy 1 ton truck has no brakes, the shoes are new, lines are bled , master cylinder tests good, but no pedal at all

Posted by on

Ad

1 Answer

Check the anti lock solinoid to the rear brakes, it has a valve and a resiviour in it, it is in the line to the rear brakes, usually the valve or diaphram goes bad, easiest way to check it is to bypass with a piece of brake line

Posted on Oct 16, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 23 t bucket and i cant get a brake pedal.when i bought it had very little brake so i replaced rear shoes and cylinders,front pads and calipers,all new lines and the master cylinder


Once you have bled the air from the brake lines,clamp off the front brake hoses carefully.Does the pedal feel better now?
Then the pad /caliper fit is allowing too much play.Is the pedal the same?Then clamp the rear hose and try the pedal.Is it fine with the rear hose clamped?If so we now know the problem is at the rear brakes.One common low pedal rear brake cause is brake shoes that do not fit the drums.Remove the drums and look at the shoes,are they showing contact wear fully or just in the middle of the shoe?Remove a shoe and place it in the drum.Can you rock the shoe against the drum surface?Once drums have been resurfaced,the shoes will not fit fully against the drum allowing the shoe the flex when applying pressure to it and this can easily create a low soft brake pedal. Of course rear brake adjustment must be correct once brake shoe contact is correct.To correct brake shoe contact,have your shoes re arc-ed to fit resurfaced drums or install new drums.Don't overlook brake master cyl /brake pedal push rod adjustment too.

Jun 24, 2017 | Cars & Trucks

1 Answer

Brake pedal goes to floor


for the pedal to go to the floor there is still air in the brake system. Start again starting from the longest line bleeding each in turn to the shortest line . make sure you have adjusted up the rear brakes before bleeding as every time you press on the pedal the shoes expand right out and when you take your foot off the pedal the shoes go all the way back in. adjust them manually and do not rely on the self adjuster as it only adjusts on wheel movement

Jul 15, 2013 | 2002 Ford Explorer Sport Trac

4 Answers

Brake pedal goes nearly to floor front pads, calipers, brake hoses changed, rotors turned Master cylinder changed, brake booster check valve changed rear brakes checked, drums good no ridge, shoe's...


I would go with not bled correctly

The booster should hold up with a hard pedal until
you start the engine, then vacuum causes it to move
down when pressing on the brake

Sep 16, 2011 | Saturn SC Cars & Trucks

1 Answer

I replaced disc brake pads, rear shoes. wheel cylinder,master cylinder, power brake booster all new. Question: My brake pedal is not solid,goes low to the floor almost. I have bled the master cylinder 1st,...


Check your lines going to the brakes the rubber hose on the 1993 chevy have a tendancy to crack and brake are you using an excess of brake fluid

Sep 12, 2011 | 1993 Chevrolet C1500

1 Answer

89 c1500, full pedal on brakes until started then goes to floor. Bled system,replaced master cylinder and anti-lock system,now has better pedal but code 4 on brake lite that won't go out. Have replaced...


adjust your rear shoes up so that the rear drums just turn, with them ajusted to a low setting the brake pedal will be low .
also when you start your engine it is noral for the pedal to drop because of the boster ! [ but not to the floor ]
Bruce Pike

Oct 10, 2009 | 1989 Chevrolet C1500

1 Answer

Brake pedal losses pressure 1 to 2 pumps back to full pressure.


you still air in system or a bad master cylinder or brake booster.

Apr 03, 2009 | 1989 Toyota Land Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

281 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...