Question about 1994 Ford Mustang

2 Answers

Brake job - 1994 Ford Mustang

Posted by on

  • Kirk Severs
    Kirk Severs May 11, 2010

    Do you need help doing a brake job? Disc or Drum? Year of your Ford Freestyle?

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have the special tool to compress the brake caliper on my front disc brakes 1994 V-6 ford Mustang....my issue is, how can i get to a rubber boot cover over the top bolt holding the caliper in place? I see the bottom bolt exposed and easy to get to, but the top bolt is covered and I don't know how to remove it or what in order to unscrew the bolt in order to remove the brake caliper. Alfred in El Paso.

Posted on Nov 22, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 170 Answers

Get a Haynes Manual for your year, make and model. you can purchase them from Auto Zone or other retailer. It give you complete, step by step instructions on repair and installation of anything on your auto, based on a complete teardown and rebuild, complete with pictures. Good Luck!

Posted on Jul 17, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Toyota sequoia vibrates when i match the brake pedder....what could be the cause and solution?


Could be the ABS system. Have the codes read. If the steering wheel also vibrates, bad rotors, brake job. Could be the rear brakes also. Again, brake job.

Jun 04, 2016 | Toyota Cars & Trucks

1 Answer

How do you get the brake light off on a 04 buick la sabra after the brake job is done


If you did the brakes correctly then the brake light should have gone off when you restarted the car.
Exactly what brake work did you do? A simple pad change or did you have to open the system up for the fluid?

Oct 10, 2014 | 2004 Buick LeSabre

2 Answers

My brake pads have been changed and the wheels continue to squeal. They rattle and squeak when driving and braking


it just sounds like a poor quality job...the proper way to do a brake job is a high quality set of front pads such as a bendix or raybestes gold line pads,, then have the front brake rotors machined an a amco brake lathe or even better a on the car brake lathe. make sure all brake caliper hardware is properly cleaned an lubercated or replaced with new hardware....then have the rear brakes adjusted( adjust only if ur car has rear drum brakes...rear disc brakes r selfadjusting

Jul 16, 2011 | 2003 Chevrolet Impala

1 Answer

Had a brake job loseing brake fluied


sounds like they might have not tightened up a bleeder screw or brake line you might consider taking it back to the garage who did your brake job.

Dec 18, 2010 | 2003 Kia Spectra

3 Answers

What should a rear brake and rear rotor replacement job cost for a 05 denali. Job description reads: replace rear disc brakes with new pads. lubricate & inspect caliper and mounting hardware, refill...


hello. Call at least three local repair shops and get quotes. Then check with the better business bureau to be sure that those shops are all respectable. J.

Jun 12, 2010 | 2005 GMC Yukon Denali

1 Answer

Abs light stays on all the time and says track off on my 2oo1 pt cruiser the brakes are working fine i have just had all new brake pads cuold this have something to do with it


was the brake light on b4 brake job? and did you do the brake job or a shop.....if the abs light wasnt on b4 brake job thenwhen the pistons on the caliper where pushed back it screwed the abs pump...if it was on b4 brake job i would look in to a abs sensor on the wheel bearings

Mar 04, 2010 | 2002 Chrysler PT Cruiser

1 Answer

Spent $600.00 at Midas about 2 years ago getting


I would suggest that you take it to another shop and have the system checked by a technician.A good pad to install is wagner thermo quiet brake pads and have them check the thickness of the rotors also.A good technician will check your complete braking system to make sure there are no faulty parts.

Feb 13, 2010 | 2004 Kia Rio

1 Answer

Chrysler 2001 - my brake pads are new, but someone said my rotors need to be changed. look like the Chrysler dealership that did my brake job, did a poor job. I have been having brake issues every...


replacing rotors is not an easy job but its not all that hard either, brake pads and calipers have to be removed, then the rotor, if your husband doesn't feel comfortable doing this i suggest you take it to a garage, they are your brakes after all :)

Feb 05, 2010 | Chrysler Town and Country Cars & Trucks

1 Answer

Brake job


A brake job is something that is done properly and I've seen so many bad brake jobs in my time. I know it is rather expensive to get a brake job done but to do it yourself one has to be very carefull that it is done right. New rotors are about 30 dollars each and then there are the seals and rotors that have to be serviced properly. Needlessly to do the whole brake job would be quite a job for you if you haven't done it before.

Feb 12, 2009 | 2002 Toyota ECHO

1 Answer

Looking for diagram of rear brakes - doing brake job


Pull both wheels off, do one at a time, use the other side as a guide to put it back together, I am a retired auto mechanic and this is the best way to do the job, also remember the larger shoe always goes to the back.

Jun 07, 2008 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
1994 Ford Mustang Logo

228 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...