Question about Hyundai Accent

1 Answer

HI, I want to know how to remove the starter solenoid (where are the nuts) and if it's possible to do it myself Thanks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 90 Answers

HI
YES IT IS POSSIBLE ?/
there is two bolt com from the(transmission fly well cover)
take this step :-
1- disconnect the battery ground cable
2- remove the speedometer cable and the shaft cable
3-disconnect the starter motor connector and terminal
4- remove the starter motor assembly

ask for more ?????????
WITH MY BEST WISHES

Posted on Jul 17, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the starter located on a 2008 pontiac g 6 4 cylinder


Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle. Remove the "S" terminal connector from the starter solenoid. Remove the engine harness lead (2) from the starter
Remove the positive battery cable nut (2) from the starter solenoid. Remove the positive battery cable (3) and engine harness terminal (4) from the starter solenoid.
Remove the starter motor bolts. Remove the starter motor.
Has four engines possible in your G6 ,starter removal is simalier for all except one the catalytic converter has to come off.

Mar 30, 2015 | 2008 Pontiac G6

1 Answer

Starter motor removal and solanoid repair if possible


Disconnect negative battery cable, unscrew the nut holding on the wiring to starter, remove two bolts holding on starter. Pull starter out. There are two bolts that hold the solenoid together, these can be removed to access the internals of the solenoid.

Jun 18, 2012 | Land Rover Discovery Cars & Trucks

1 Answer

Unable to remove starter on a lincoln navigator 2000


Where are you stuck?
Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. NOTE: To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. Start the engine several times to check starter motor operation.
Let me know how you make out..

Feb 17, 2011 | Lincoln Navigator Cars & Trucks

1 Answer

I have a 1999 isuzu rodeo 2WD 3.2L V6. What are the steps in replacing my starter. My car is stranded and i need to try to replace it myself?


The repair manual book says first disconnect the battery , then lift the car to have more space to work on it make sure that is secure if you liftit ,remove the nut to Starter ,also nut to solenoid cable ,or if you think it is easier take off starter first and then after remove nuts to starter and solenoid ,then you ready to install you new or rebuilt starter ,,good luck

Nov 26, 2010 | 1999 Isuzu Rodeo

1 Answer

HOW TO REMOVE A STARTER FROM A SATURN SC1 97


Please see my tip at http://www.fixya.com/cars/r5973094-starter_replace . These are generic instructions. If you get stuck or need specific instructions for your car, please get back to me with model, year and engine info.
I have pasted specific instructions for your car below from autozone.com


REMOVAL & INSTALLATION See Figures 2 through 10

  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. If equipped, remove the starter shield pin by pulling on it with pliers, then lift and release the shield from the solenoid.
  4. Spray the solenoid electrical connection nuts and studs with penetrating oil, and allow it to seep in for a minute to loosen the connections. While the oil is soaking in, tag the solenoid electrical connectors for identification during assembly.
It is very important that the solenoid electrical connection nuts and studs are sprayed with penetrating oil prior to removal to avoid damage to the solenoid end cap. A cracked cap will allow debris and moisture to enter and corrode the solenoid contacts.
  1. Carefully loosen the bolts and detach the starter electrical connectors. Position the wires to the side and out of the way.
  2. Remove the lower starter mounting bolt.
  3. Using an obstruction wrench, remove the upper starter mounting bolt. If the upper starter mounting bolt cannot be reached from below the vehicle, it may be accessible from above, through the intake manifold support bracket opening.
  4. If equipped, remove the bolt attaching the starter rear support bracket to the vehicle. Rotate the starter until the bracket misses the axle shaft support bracket.
  5. Carefully support the starter, pulling it rearward and toward the left side of the vehicle to remove it.


jturcotte_43.gif Fig. Fig. 2: Remove the starter motor dust shield retaining clip

jturcotte_44.gif Fig. Fig. 3: Lift off and remove the starter motor dust shield from beneath the vehicle

jturcotte_45.gif Fig. Fig. 4: Loosen the starter solenoid wiring terminal screws ...

jturcotte_46.gif Fig. Fig. 5: ... then label and disengage the wiring harnesses from the starter solenoid, carefully positioning them out of the way

jturcotte_47.gif Fig. Fig. 6: Loosen the lower starter motor mounting bolt ...

jturcotte_48.gif

Fig. Fig. 7: ... then remove the bolt from the vehicle

jturcotte_49.gif Fig. Fig. 8: If accessibility is limited from below the vehicle, use the opening in the intake manifold support bracket to reach the upper starter bolt

jturcotte_50.gif

Fig. Fig. 9: Remove the rear mounting bracket bolt, then remove the starter from the vehicle

jturcotte_51.gif Fig. Fig. 10: If the starter is to be replaced, remove the bracket from the old starter


To install:

  1. If equipped on the old starter, install the rear starter support bracket to the new starter. Tighten the bracket nuts to 7 ft. lbs. (9 Nm).
  2. Guide the starter into the bell housing and rotate the assembly until the lower bolt hole in the starter aligns.
  3. Verify that the bracket is properly aligned and loosely install the bracket bolt, then loosely install the starter mounting bolts. It may be necessary to raise or lower the vehicle for access to both the upper and lower bolts, but do not tighten any bolts until all of the mounting bolts have been started.
  4. Tighten both upper and lower starter assembly attachment bolts to 27 ft. lbs. (37 Nm).
  5. Reconnect the electrical wires and install the nuts. Be careful not to overtighten the nuts and crack the solenoid end cap. Route the wiring cable so it will not contact any rough surfaces. Tighten the starter positive terminal nut to 89 inch lbs. (10 Nm) and the solenoid terminal nut to 44 inch lbs. (5 Nm).
  6. If equipped, install the starter shield and push pin, being careful that the pin is positioned for possible future removal.
  7. Lower the vehicle.
  8. Connect the negative battery cable and verify operation.

Nov 05, 2010 | Saturn SC1 Cars & Trucks

1 Answer

Starter diagram for a 1994 dodge intrepid


3.3L Engine
  1. Disconnect the negative (-) battery cable. Raise and safely support the front of the vehicle on jackstands. Fig. 1: Disconnect the negative battery cable 88172g31.gif

  2. Remove the three bolts attaching the starter to the engine/transaxle. Fig. 2: Remove the three starter mounting bolts 88172g32.gif
    CAUTION
    Be careful when removing the starter motor mounting bolts, the motor can be quite heavy. Personal injury could result if the starter motor falls from its mounting position.
  3. Remove the starter from the the transmission housing. Position the starter to gain access to the wiring connectors.
  4. Remove the battery positive cable nut from the starter and remove the cable. Fig. 3: Remove the battery positive cable nut from the starter and remove the cable 88172g33.gif

  5. Disconnect the push on solenoid connector.
  6. Remove the starter from the vehicle. To install:
  7. Clean all wire terminals of dirt, grease or corrosion.
  8. Attach the electrical wire connectors and secure with the mounting nuts. Tighten the starter solenoid B+ nut to 90 inch lbs. (10 Nm) and the solenoid wire-to-starter nut to 55 inch lbs. (6 Nm).
  9. Hold the starter motor in place, then secure in place with the 3 attaching bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).
  10. Lower the vehicle.
  11. Connect the negative (-) battery cable.
3.5L Engine
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle.
  3. For easier servicing, do not remove the wiring from the starter motor at this time.
  4. Remove the three bolts attaching the starter to the engine. Fig. 4: Remove the three bolts attaching the starter to the engine 88172g34.gif

  5. Remove the starter solenoid assembly from the transfer housing. Position the starter to gain access to the wiring connectors.
  6. Remove the battery positive cable nut from starter and remove the cable.
  7. Disconnect the push on solenoid connector.
  8. Remove the starter from the vehicle. To install:
  9. Clean all wire terminals of dirt, grease or corrosion.
  10. Attach the electrical wire connectors and secure with the mounting nuts. Tighten the starter solenoid B+ nut to 90 inch lbs. (10 Nm) and the solenoid wire-to-starter nut to 55 inch lbs. (6 Nm).
  11. Hold the starter motor in place, then secure in place with the 3 attaching bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).
  12. Lower the vehicle.
  13. Connect the negative battery cable.
prev.gif next.gif

Oct 15, 2010 | Dodge Intrepid Cars & Trucks

1 Answer

How to install starter for 1996 Saturn SC2


prev.gif next.gif REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. If equipped, remove the starter shield pin by pulling on it with pliers, then lift and release the shield from the solenoid.
  4. Spray the solenoid electrical connection nuts and studs with penetrating oil, and allow it to seep in for a minute to loosen the connections. While the oil is soaking in, tag the solenoid electrical connectors for identification during assembly. NOTE: It is very important that the solenoid electrical connection nuts and studs are sprayed with penetrating oil prior to removal to avoid damage to the solenoid end cap. A cracked cap will allow debris and moisture to enter and corrode the solenoid contacts.
  5. Carefully loosen the bolts and detach the starter electrical connectors. Position the wires to the side and out of the way.
  6. Remove the lower starter mounting bolt.
  7. Using an obstruction wrench, remove the upper starter mounting bolt. If the upper starter mounting bolt cannot be reached from below the vehicle, it may be accessible from above, through the intake manifold support bracket opening.
  8. If equipped, remove the bolt attaching the starter rear support bracket to the vehicle. Rotate the starter until the bracket misses the axle shaft support bracket.
  9. Carefully support the starter, pulling it rearward and toward the left side of the vehicle to remove it. To install:
  10. If equipped on the old starter, install the rear starter support bracket to the new starter. Tighten the bracket nuts to 7 ft. lbs. (9 Nm).
  11. Guide the starter into the bell housing and rotate the assembly until the lower bolt hole in the starter aligns.
  12. Verify that the bracket is properly aligned and loosely install the bracket bolt, then loosely install the starter mounting bolts. It may be necessary to raise or lower the vehicle for access to both the upper and lower bolts, but do not tighten any bolts until all of the mounting bolts have been started.
  13. Tighten both upper and lower starter assembly attachment bolts to 27 ft. lbs. (37 Nm).
  14. Reconnect the electrical wires and install the nuts. Be careful not to overtighten the nuts and crack the solenoid end cap. Route the wiring cable so it will not contact any rough surfaces. Tighten the starter positive terminal nut to 89 inch lbs. (10 Nm) and the solenoid terminal nut to 44 inch lbs. (5 Nm).
  15. If equipped, install the starter shield and push pin, being careful that the pin is positioned for possible future removal.
  16. Lower the vehicle.
  17. Connect the negative battery cable and verify operation. Fig. 1: Remove the starter motor dust shield retaining clip 89562p17.jpg
    Fig. 2: Lift off and remove the starter motor dust shield from beneath the vehicle 89562p18.jpg
    Fig. 3: Loosen the starter solenoid wiring terminal screws . . . 89562p19.jpg
    Fig. 4: . . . then label and disengage the wiring harnesses from the starter solenoid, carefully positioning them out of the way 89562p20.jpg
    Fig. 5: Loosen the lower starter motor mounting bolt . . . 89562p22.jpg
    Fig. 6: . . . then remove the bolt from the vehicle 89562p23.jpg
    Fig. 7: If accessibility is limited from below the vehicle, use the opening in the intake manifold support bracket to reach the upper starter bolt 89562p15.jpg
    Fig. 8: Remove the rear mounting bracket bolt, then remove the starter from the vehicle 89562p21.jpg
    Fig. 9: If the starter is to be replaced, remove the bracket from the old starter 84193011.gif

Sep 24, 2010 | 1993 Saturn SC2

1 Answer

How do you replase a starter in a 2500 C GMC?


Disconnect the negitive battery cable,#2remove the 4 bolts holding the flywheel inspection cover(10mm head)#3try to access the wires on the starter solenoid large wire should be a 13mm nut and small one should be 1/4" socket to fit the nut.If you can't get up to them thats ok we will get to them after lowering starter.Remove the 2 starter bolts (either a 9/16 or 15mm socket) DON'T let the starter drop it will tear your wires.Next remove the 2 nuts I said about before make sure you save the lock washers if your new starter doesn't have any also make sure you pay attention to how the wires are on the solenoid postion and correct stud or treminals.The large battery wire is keyed to go on one way only tab on terminal fits in slot on solenoid.if you get this off center you will crack solenoid and have to replace it .Reverse procedure to install.GOOD LUCK

Feb 14, 2010 | 1985 GMC C2500

1 Answer

How to change a starter on 1984 chevy c10 with a 305


First disconnect the power cable from the battery. If your starter has a mounting bracket on the nose undo that nut first ( some have, some don't). Undo the nut that holds the battery cable to the starter and remove the wires ( count them so you know how many go back on). Under the truck you have to remove the inspection cover from the front of the transmission next to the motor. Undo the 2 bolts on the bottom of the starter. When these come out the starter will drop so be prepared because you still have 1 wire attached. Ease the starter down and remove the small wire from the inside of the solenoid and take the starter out with you. When you get the rebuilt starter from the autoparts store make sure you get a new solenoid. An old solenoid and a new starter is kind of like recycling used toilet paper, possible but not worth the trouble. It goes back in the reverse of taking it out.
BE CAREFUL putting the small wire back on the new solenoid. It has to be tight but you can easily strip it if you get carried away with it. If by chance that happens just double nut it with the nut from the old one and you'll be okay. Hope this helps.

Dec 19, 2009 | 1984 Chevrolet Chevy

2 Answers

Whers is the starter on a 1996 saturn sl and what is the best way to replace it


Just is one way to replace. Review this:

1996 Saturn SL 1.9L MFI SOHC 4cyl

1fe174c.jpg

If the starter is to be replaced, remove the bracket from the old starter

REMOVAL & INSTALLATION
  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
  3. If equipped, remove the starter shield pin by pulling on it with pliers, then lift and release the shield from the solenoid.
  4. Spray the solenoid electrical connection nuts and studs with penetrating oil, and allow it to seep in for a minute to loosen the connections. While the oil is soaking in, tag the solenoid electrical connectors for identification during assembly.
It is very important that the solenoid electrical connection nuts and studs are sprayed with penetrating oil prior to removal to avoid damage to the solenoid end cap. A cracked cap will allow debris and moisture to enter and corrode the solenoid contacts.
  1. Carefully loosen the bolts and detach the starter electrical connectors. Position the wires to the side and out of the way.
  2. Remove the lower starter mounting bolt.
  3. Using an obstruction wrench, remove the upper starter mounting bolt. If the upper starter mounting bolt cannot be reached from below the vehicle, it may be accessible from above, through the intake manifold support bracket opening.
  4. If equipped, remove the bolt attaching the starter rear support bracket to the vehicle. Rotate the starter until the bracket misses the axle shaft support bracket.
  5. Carefully support the starter, pulling it rearward and toward the left side of the vehicle to remove it.
To install:
  1. If equipped on the old starter, install the rear starter support bracket to the new starter. Tighten the bracket nuts to 7 ft. lbs. (9 Nm).
  2. Guide the starter into the bell housing and rotate the assembly until the lower bolt hole in the starter aligns.
  3. Verify that the bracket is properly aligned and loosely install the bracket bolt, then loosely install the starter mounting bolts. It may be necessary to raise or lower the vehicle for access to both the upper and lower bolts, but do not tighten any bolts until all of the mounting bolts have been started.
  4. Tighten both upper and lower starter assembly attachment bolts to 27 ft. lbs. (37 Nm).
  5. Reconnect the electrical wires and install the nuts. Be careful not to overtighten the nuts and crack the solenoid end cap. Route the wiring cable so it will not contact any rough surfaces. Tighten the starter positive terminal nut to 89 inch lbs. (10 Nm) and the solenoid terminal nut to 44 inch lbs. (5 Nm).
  6. If equipped, install the starter shield and push pin, being careful that the pin is positioned for possible future removal.
  7. Lower the vehicle.
  8. Connect the negative battery cable and verify operation.
15aebbb.jpg

Fig. Remove the starter motor dust shield retaining clip


75381aa.jpg
Fig. Lift off and remove the starter motor dust shield from beneath the vehicle


98d7fb8.jpg
Fig. Loosen the starter solenoid wiring terminal screws ...

f05fd78.jpg

Fig. ...then label and disengage the wiring harnesses from the starter solenoid, carefully positioning them out of the way


348d2a8.jpg
Fig. Loosen the lower starter motor mounting bolt ...


46ba7f0.jpg
Fig. ...then remove the bolt from the vehicle


08946b5.jpg
Fig. If accessibility is limited from below the vehicle, use the opening in the intake manifold support bracket to reach the upper starter bolt

3233aaf.jpg

Fig. Remove the rear mounting bracket bolt, then remove the starter from the vehicle




I hope help you with this (remember rated this help) Good luck.

Oct 16, 2009 | 1996 Saturn SL

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

176 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...