Question about 1996 Dodge Dakota

4 Answers

BLOWER MOTOR WILL NOT WORK IN MY 2003 DODGE DAKOTA, HAVE CHECKED ALL FUSES AND REPLACED BOWER, IT STILL WILL NOT WORK

Posted by on

  • 4 more comments 
  • jimmythegato Jul 17, 2008

    1998 Dodge Dakota blower motor quit working. If you could please tell me where its located at, personally Im a ford man. Ive looked everywhere on this dodge and I cant find it.

  • timmy301 Oct 04, 2008

    1995 dodge dakota blower is not working how do i fix it

  • izzyironhead Nov 26, 2008

    my blower motor quit without warning on my 96 dodge dakota. im freezing and need help bad. thanks for your help. Freezin in Ohio

  • Anonymous Jan 01, 2009

    I just had the same problem and I went and foud that terminal at the fire wall and it had a bad connection, so I just took a terminal cleaner and scrub the connection till it had a clean surface and put it back together and it blew strong....thanks for all the help and hope everyone's elses repair was as easy as mine..

  • brentmaria Jan 12, 2009

    I have the same problem....but (1) I can NOT find the right fuse for the blower motor. Where is it? (2) Where is the Blower Moter Relay? The Rear Blower Motor Relay spot does not have a relay! (3) Where is the termination connector at the firewall, engine or cab? Where is the resistor? Thanks

  • dhbomb344 Jan 20, 2009

    I have a 1996 Dakota V8 and the heater went out. None of the fan speeds work. Yesterday, the fan came on when set on High. When I set it to Low, the same thing happened. None of the speeds work at all.

×

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

Try a new mopar fan resistor that is on the passenger side of the firewall, held in by two screws. if you take it out of the firewall you will see that one of the coil wires has melted/broken like a light bulb filament.
they are around $12.00 new .

you only need to unhook your car battery-losen the two screws-replace the wires in the same position on the new resistor- remount it back into the firewall. rehook the battery.

poor connections are common due to rust-corrosion on the five wires. baking powder and water mix on the connections. clean and coat with battery terminal sparay.

mopar id # 1-04462841

Posted on Feb 24, 2009

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 12 Answers

On a 2003 dakota, the resistor is located under the passenger side dash, near the glove box.

Posted on Nov 26, 2009

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I'm not sure about your 2003 but I've just recently purchased a 96 and it has a terminal block mounted to the firewall on the passenger side. This block has about 6 yo 8 wires going to it and one of the wires goes to the blower motor. On this truck the wire is black with a yellow stripe, if I wiggle this wire it sparks at the terminal block and the blower motor works. I think all that this block is, is just a grounding block. I had a similar problem with my dad's chevy pickup and the ground wire to it was burnt. It mounted in the same place this dodge does. I just replaced the wire and it worked fine. Hope this helps and doesn't come too late.

Posted on Oct 21, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I had a 1991 with the same problem. I ended up just bypassing the factory switch and dealing with high or off wit a standard toggle switch. not thebest solution it would get hot but it got me by.

Posted on Apr 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

A//c unit works only on high speed/


blower motor resistor...it cuts power to lower settings...easy fix usually under passenger side glovebox two screws and harness looks like a metal card with plastic bottom...

Jan 28, 2016 | 2004 Dodge Dakota

2 Answers

The fan motor switch in my 1990 dodge dakota does not work. I have checked the blower motor out and the fuses out. and the resistor out. they all are fine. I am not getting any juice to the fuse box for...


Have you checked the blower motor resistor. Usually locate in the blower box with a plug on it. Has 2 bolts holding it in. Take out and inspect.

Nov 24, 2010 | 1992 Dodge Dakota

2 Answers

Blower not working


Either the blower motor itself has gone bad or you have a fuse blown. Could also be a bad connection at the blower motor. Check all the fuses and then the wires at the blower with a test light. You can also use two wires and run them as a straight wire from the battery to the blower motor, one as a hot and the other as a ground, to ensure the blower is good. Also check your switch on the dash.

Jun 25, 2010 | 2002 Dodge Dakota Club Cab

1 Answer

2003 Dodge Dakota heater blower just quit working, what could be the cause??


It could be the blower motor resistor module.It is located on the passengers side next to the blower motor.Make sure the connections are not melted.Because if they are you will have to replace them also.Hoope this helps.Good luck.

Feb 01, 2010 | 2003 Dodge Dakota Club Cab

1 Answer

2002 DODGE DAKOTA, BLOWER MOTOR QUIT, CHECKED FUSES, REPLACED MOTOR, REPLACED RESISTER, STILL DOESNT WORK ?????


if u changed all of that then it should be the heater control . have u given direct power to the blower motor? it is possible that its faulty.

Jan 25, 2010 | 2002 Dodge Dakota Club Cab

1 Answer

Switch not turning on blower motor


if you have an owners manual in the glove box,it will tell you where the fuse locations are and what each fuse feeds

Jan 10, 2010 | 2003 Dodge Dakota Club Cab

2 Answers

Heat & A/C Blower Controls Inop. 2003 Dodge Dakota 6cyl


The resistor will cost you 12 dollars at your local dealership. It's located under the passenger side dash and is very easy to replace. The resistor installed at the factory is defective and the new one from Mopar is the correct resistor. It would be worth you while to replace it now while you're working on the blower motor. The blower should still work on the high setting, even with a bad resistor but, replacing the resistor may fix the problem.

Sep 19, 2009 | 2003 Dodge Dakota Club Cab

2 Answers

A/c/heater bower stopped working 2004 Dodge Dakota


Check Your heater blower motor resisto located somewhere on the heater box.

Jul 27, 2009 | 2004 Dodge Dakota

1 Answer

1992 dakota- blower motor willnot work. a/c was on


Check the connections at the blower resistor.

May 13, 2009 | 1992 Dodge Dakota

1 Answer

2003 dodge dakota,blower problem


you likely need to replace the blower motor resistor

Jan 15, 2009 | 2003 Dodge Dakota Club Cab

Not finding what you are looking for?
1996 Dodge Dakota Logo

656 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...