Question about 1993 Chevrolet K1500

1 Answer

AC wiring I had a single two wire plug on an r 12 ac compressor switch to a new compressor for 134 a which two two wire plugs, can I make this work for my truck?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,450 Answers

You have two plug ins?
if yours did not have the high side cutout on back of compressor just leave it in and wire like yours was

Posted on Sep 22, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have a 95 grand jeep chrokee limited 5.2 liter pcm will not ingauge AC clutch relay


the AC compressor has a "shutdown switch" when not enough refrigerant is in the system run a wire from the

run a wire from the + battery cable to the compressor pulley switch with the engine running, ac on if the compressor clucth engages (turns) you have low refrigerant charge





=

Feb 05, 2013 | 1995 Jeep Grand Cherokee

1 Answer

Full of freone,getting power to comprestor but still will not come on? What do you think?


Ok here is how to check if the compressor is (not spinning) Follow the aluminum lines off the AC compressor under the hood until you find the pressure sensor it will have a plug with two wires coming off of it, unplug it and get a 2 or three inch piece of wire like speaker wire or something that has a bunch of small wires in it and not a big solid single wire, strip both ends of the wire and insert them into the plug holes of the switch plug this should engage the compressor if not the compressor may be bad if so let the compressor run for a little while if the ac gets cold the pressure sensor is bad

May 30, 2011 | 2000 Jeep Grand Cherokee

2 Answers

Ac not blowing cold, check main relays, has r12, jumpered and clutch kicks in. checked all fuses and relays swapped horn and ac OK... she has the push button ac controls.... thinking its something with...


there is a pressure switch on the ac drier that is the big silver can looking thing by the dash under the hood... if this goes bad the ac compressor will not kick on and the fans will not run when the ac is turned on... if the fans are not running at the same time of the ac compressor it will not blow cool..

Jun 12, 2010 | 1992 Buick LeSabre

1 Answer

AC blowinghot air


Locate wires coming from compressor clutch and trace to nearest plug that you can unplug. Turn on A/C to max cooling. If clutch not engaged (center of compressor drive pulley not spinning with pulley), unplug compressor clutch wires and use multimeter to check voltage going to compressor clutch. If voltage is around 12 volts or more, then clutch should be engaged when plugged in. Plug clutch wires back in (with motor still running and ac set to max). If clutch still not engaged, then clutch definitely bad because 12V signal should engage it.

May 08, 2010 | 2002 Lincoln LS

2 Answers

What causes a1994 honda accord engine to stall when the air conditioner is turned on


plugs and wires time ! Most likely, as when the engine takes that kind of load (it works much harder when ac is turned on) weak plugs and or wires wont keep the rig running. Imports like yours have a plethora of things that are interconnected... that or your AC condensor - compressor is bad- and when it engages on your engine, (one of the things the serpentine belt is connected to) it CANNOT turn on the inside, and since it is trying to turn your compressor-condensor at the same time as everything else, it just stalls out. If you can live without the ac, you can usually buy a belt that will be shorter for non-ac versions of your car, or it will have a seperate belt all on its own. the compressor-condensor is the peice with all the metal tubes and rubber tubes around it. This will also give you better mileage. Have a nice day!

Aug 16, 2009 | Honda Accord Cars & Trucks

1 Answer

Can some post the 1999 gmc sierra wiring diagram


you don't have enough pressure in your system. odds are you have a leak someplace and the factory installed a saftey switch to keep the ac from running when there is no pressure. This way you don't end up burning up your compressor.

Jun 28, 2009 | 1999 GMC Sierra

2 Answers

Need to recharge ac in 1995 chevrolet blazer. Not


1995 should have 134A. Look on the compressor and in the middle of it will be a sticker that says 134a or r12. If it is r12, you must retrofit it in order to charge it yourself.

Jun 24, 2009 | 1995 Chevrolet Blazer

2 Answers

No power for AC compressor


try removing the plug off the low pressure switch on the accumalator plug a paper clip into the plug and turn ac on if it comes on then your low pressure switch is bad or your low on refigerant.

May 28, 2009 | 2000 Chevrolet S-10

2 Answers

I need to know how to jump the ac low pressure to get my ac compressor to come on.


If you look on the low pressure side of the AC system you will see a plug that is incorporated in to the line. It will have two wires leading to it. Remove the plastic clip that attaches the two wires to the sensor and use a short piece of wire to connect the two terminals in side the plug by putting the ends into the cap. This will bypass the low pressure sensor and allow the AC clutch to engage and begin to cycle again. Remember this low pressure switch is there for a reason. If you don't add more r-134 to the system and allow the AC compressor to cycle you will destroy the compressor. You need to charge the system when you bypass the low pressure switch and get the system up to full charge status and reconnect the switch.

May 24, 2009 | 1995 Chevrolet Camaro

2 Answers

1998 cadillac deville still reads service ac system


Check the wire connectors and wires for any breaks that are on the A/C line.

Jan 07, 2009 | 1998 Cadillac DeVille

Not finding what you are looking for?
1993 Chevrolet K1500 Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6879 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...