Question about 1998 Honda Accord

2 Answers

Remove front bumper honda accord - 1998 Honda Accord

Posted by on

  • 2 more comments 
  • Mark Jones Oct 05, 2008

    I also need to remove the rear bumper of my Honda Odyssey 2000 EX

  • Mark Jones Oct 05, 2008

    I have a Honda Odyssey 2000 EX I have to remove the front bumper how do I do this?

  • ndvice1 Nov 02, 2008

    Does anyone know how to remove & replace the front bumper on a 1998 Honda Accord Sedan?

  • zoie4whoie Feb 14, 2009

    I am having the same problem on a 96 accord LX. Is it the same removal as the 98 accord

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Director Badge:

    Uploaded 100 video answers.

  • Expert
  • 159 Answers

If it's a 94-97 Honda Accord,this video will show you how to remove it.

Posted on Jan 28, 2011

×

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 34 Answers

You will need to remove the 2 front signal lights by loosening the single captive screw on each of them. under the signal lights , you will see 2 14" bolts holding each side of the bumper. make sure you loosen the screws that hold the bumber to the fenders.

Posted on Oct 14, 2008

5 Suggested Answers

MNfisherman
  • 11896 Answers

SOURCE: I WANT TO REMOVE THE FRONT BUMPER ON MY 2000 HONDA

reach underneath bumper, you will see the post with screws on each post. Just remove the nuts on both sides, and bumper will come off.

Posted on Jun 12, 2009

  • 6 Answers

SOURCE: 2005 Honda Accord Front Bumper cover replacement

easy there is a screw on both sides were bumper and fender meet just pop back fender liner its a phillips head. Then pop hood remove clips on black trim infont of radiator. Underside where bumper goes under car remove those clips and 10mm bolts after all is removed bumper just pulls off ...... may have to give it a hard **** a few times but it will come off. Should only take 15-20min to remove if its your first time

Posted on Jul 03, 2009

  • 564 Answers

SOURCE: cant remove the tail light assemblies on '09 accord sedan

youll have to pull up very firmly or it may have to slide to the side its held in place by a bodyfastener. a screw that fits into a slot. but i would try pulling up first.

Posted on Dec 29, 2009

  • 1 Answer

SOURCE: How do you remove the front bumper cover on a 98

remove front bumper on 1995 honda accord

Posted on Mar 06, 2010

varun_engr
  • 516 Answers

SOURCE: how to install a front bumper for a 1996 Honda accord sedan

Installation of a front bumper can be complicated. These helpful instructions may help a person with this task. If you choose to install a bumper yourself, please be cautioned that professional installation is always recommended. Please confirm before you start that your safety equipment has been applied to you, your car and your new bumper. These 10 easy steps can make a difficult install relatively easy.
The following steps are detailed instructions that you can follow. It is very important that you make sure to read each step carefully and completely:
1. Look closely at the new bumper and your car for screws, bolts and clips. Remove these pieces from your existing front bumper and place them in a safe area. Follow this by the full removal of the cars current front bumper.
2. Next, test the fit of the new front bumper. Make sure that nothing hinders with the placement and fit on the car.
3. If the fitment is correct the installation process may move forward.
4. If the fitment is incorrect then the removal or repositioning of certain components, such as reinforcement bars may be required. This is because every car is different. If this is the case remove the element and test fit the front bumper again. This should be done with caution and is done at the installers own risk.
5. Most of the time the new aftermarket bumper is placed the exact way the factory piece was. The most important key to great fitment in installation is the drilling procedure. The holes should be drilled in the places that will give the piece a great fit. Usually, these holes will be drilled in the same place as the factory bumper. At this point only mocking is required.
6. When the bumper is in place, shaving or filing maybe required. Many parts will require this because certain areas are made with more material to lower the risk of damage. Also, if a car has been in an accident or previously modified, this may cause additional sanding, cutting or filing.
7. Now that the front fits well, be very precise and drill the holes.
8. Prepping for paint is what needs to be done after the holes have been drilled. Depending on what material the front bumper is made of will determine the steps for prepping.
9. After the piece has been painted, clear coating may be appropriate.
10. Make sure there are not any leftover parts and that everything is secure. After this is done, your front bumper installation process is complete.

Posted on Jun 02, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove front bumber 1996 honda accord-lx


There will be a number of smaller screws around the outside of the bumper, like in the wheel well and under the car by the splash shield under the engine. All of those will need to be removed. Then you need to remove the turn signal lights in the front bumper with a long phillips screwdriver. Take a flashlight and look inside the bumper through the lower grill at the side of the turn signal housing. You'll see a small hole for the screwdriver. The screw doesn't need to come all the way out to remove the light.
Remove turn signal housing on both sides and look back at the frame crossmember behind the bumper. There are two large bolts on each side holding the bumper on. You'll need some extensions to reach them. Once those are out, you'll be able to tell if you missed any smaller screws/clips.

Mar 24, 2014 | 1996 Honda Accord

2 Answers

How do i change my headlight assembly on a 2001 honda accord


HEADLIGHT REPLACEMENT

1. Remove the front bumper
2. Disconnect the connectors (A).
3. Remove the 5 mounting bolts (B), then remove the headlight assembly (C).

Fig. 21: Removing Mounting Bolts & Headlight Assembly
6_26_2012_3_27_45_pm.jpg

Jun 24, 2012 | 2001 Honda Accord

2 Answers

How do you remove the front bumper cover on a 98 honda accord sedan EX


Apply the parking brake and raise the vehicle and support it securely on jackstands.

Disconnect the negative battery cable, then the positive battery cable and wait two minutes before proceeding further (make sure you have the code if you have an anti-theft radio because you will need it after disconnecting the battery).

Working under the vehicle, detach the screws securing the lower edges of the bumper cover (use a small screwdriver to pop the center button up on the plastic fasteners, but do not try to remove the center buttons. They stay in the ferrules)

Remove the bolts, screws and plastic pins on each side retaining the bumper cover to the splash shields. Remove the bolt on each side where the bumper cover attaches to the fender.

Working at the top, detach the retaining bolts (2) securing the bumper cover to the hood latch support. Remove the cover.

When you put it back, make sure the tabs along the top edge of the bumper cover fit into the corresponding clips on the body before attaching the bolts and screws. An assistant is helpful.

Hope this helps you.

Jan 05, 2010 | 1998 Honda Accord

1 Answer

Front bumper cover is broken, no lights along bottom.


Under the bumper cover is a fiberglass bumper. It could be broken or your bumper mounts could be bent on that side. It is best to remove the screws (on the side of the wheel well) and 10mm bolts holding the bumper cover, and locate the two frontal bolts in each bracket. There are also some plastic push pin nuts in various spots too. Don't try to get the push pins under the headlights, they will come with when the bumper is removed.

Sep 25, 2009 | 1993 Honda Accord

3 Answers

2005 Honda Accord Front Bumper cover replacement


easy there is a screw on both sides were bumper and fender meet just pop back fender liner its a phillips head. Then pop hood remove clips on black trim infont of radiator. Underside where bumper goes under car remove those clips and 10mm bolts after all is removed bumper just pulls off ...... may have to give it a hard **** a few times but it will come off. Should only take 15-20min to remove if its your first time

Jun 11, 2009 | 2005 Honda Accord

1 Answer

I WANT TO REMOVE THE FRONT BUMPER ON MY 2000 HONDA ACCORD


reach underneath bumper, you will see the post with screws on each post. Just remove the nuts on both sides, and bumper will come off.

Jun 09, 2009 | 1998 Honda Accord

1 Answer

Front turn signal removal....


there are slots with screws holding the lenses to the bumper..should be able to reach them with a long phillips screwdriver. use a flashlight to see the slots on the lense ...they are deep unscrew them and pull the lense out

Apr 01, 2009 | 1996 Honda Accord

1 Answer

Better way to replace the front bumper


Yes go onto ebay and get a new bumper. I have ordered alot off of there

Feb 08, 2009 | 1998 Honda Accord

2 Answers

Bumper cover removal


Its easy look at the bottom of the bumper has retainers and the fenders have a bolt on each side then just slide off

Jan 23, 2009 | 1991 Honda Accord

1 Answer

How can I change the headlights in a 1998 Honda Accord?


Its not that hard but you have to remove bumper to get to the two bottom bolts that holds the headlights. First remove grille and there are 2 10mm bolts that holt the tip of fenders they are the first bolts under the fender weld closes to the bumper cover. Then there are two bumper mounts/brackets that hold bumper to frame/radiator support. they are held by (4) 12mm bolts may need a swivel socket to get to them( easily accessed if you remove front signal lights in the bumper held by philips screws in the corners).After removing bracket bumper should come right off. Headlights are in plain clear view. (4) 10mm bolts and you are done. Re-install in the reverse. Good Luck . If I fixed ya leave me a FIX-YA comment. Contact me if you need more info

Dec 10, 2008 | 1998 Honda Accord

Not finding what you are looking for?
1998 Honda Accord Logo

Related Topics:

1,598 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...