Question about 2004 Chrysler Sebring

1 Answer

How do i change the headlight bulb in a 2005 sebring convertable

Changing headlight bulb

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 550 Answers

Lift up the hood, the bulbs are changed from the engine compartment
behind the lamp are connectors, pull it off, and the retainer that holds the bulb in
replace bulb
replace retainer
replace wire
close hood
usually takes longer to type than to do

Posted on Jul 14, 2008

  • Shirley McKinney Nov 06, 2011

    Is it the same for a 2004 Sebring as well?

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix headlight on Chrysler Sebring


you could have the wrong bulb..could be bad connection...turn light on dim..take bulb from other side..and try it that way..before going any futher...

Nov 08, 2014 | 2007 Chrysler Sebring Sedan

1 Answer

I changed headlight bulb but it won't light


1. Never touch the lamp glass with bear hands
2. Visual inspect the connector
3. With a multimeter check the voltage on the connector
3.1 If you have aroubd 12 VDC cabling is ok and you need a new buld
3.2 If not check the cabling connection

Nov 02, 2014 | 2005 BMW 325Ci Convertible

1 Answer

How do i change headlights


That is a somewhat common problem with those. If you remove the bulb from the back of the headlight lens under the hood you can some times put a funnel into the open socket and use a hair dryer to dry the condensation. Then you need to be sure the rubber gasket between the lens and the bulb socket is in good repair so it dont build up like that again, I hope this helps.

Sep 21, 2012 | 2002 Chrysler Sebring

2 Answers

How do i get to my low beams on my chrysler 2005 sebring sedan i got to the high beams perfect but the low beams right next to it has a metal barrier surrounding it which makes it impossible


Unfortunately, the answer I have is not a happy one =(. My wife has a 2005. In order to replace the bulb you will have to pull the Crutons (plastic push pins) that hold the front bumber cover on, remove the Headlight housing & replace the bulb that way. Shame on Chrysler for making it so difficult, in my opinion. But I hope this helps you to change the bulb =)

Aug 26, 2011 | 2004 Chrysler Sebring

1 Answer

Need to replace headlight lens on a 1996 dodge avenger


Usually, one has to get the entire headlight assembly to replace the lens.
Is it cracked?
If it is just faded, try some anti-haze polish for headlights. This can save you some money compared to restoring the headlamp by replacing the assembly (which may be available from a salvage yard).

---
REMOVAL & INSTALLATION

CAUTION
Halogen bulbs contain gas which is under
pressure. Handling the bulbs incorrectly could cause it to shatter into flying
glass fragments. Do NOT leave the light switch ON. Always allow the bulb to cool
before removal. Handle the bulb only by the base; avoid touching the glass
itself. Whenever handling a halogen bulb, ALWAYS follow these precautions:

  • Turn the headlight switch OFF and allow the bulb to cool before
    changing it. Leave the switch OFF until the change is complete.
  • ALWAYS wear eye protection when changing a halogen bulb.
  • Handle the bulb only by its base. Avoid touching the glass.
  • DO NOT drop or scratch the bulb.
  • Keep dirt and moisture away from the bulb.
  • Place the used bulb in the new bulb's package and dispose of it properly.


Cirrus, Stratus, Sebring Convertible and Breeze


  1. Open the vehicle's hood and secure it in an upright position.
  2. Disconnect the negative battery cable.
  3. Remove the 2 screws securing the headlight module to the radiator closure
    panel.
  4. Pull out the headlight module from the vehicle.





    Fig. 1: Using a Torxhead screwdriver, remove the 2 headlight
    module retaining screws
    90906p69.jpg






    Fig. 2: Pull the headlight module straight out of the front of
    the vehicle to remove the bulbs
    90906p70.jpg






    Fig. 3: Disconnect the wiring harness for the headlight bulb
    90906p74.jpg






    Fig. 4: Turn the light bulb retaining ring counterclockwise,
    and remove it from the back of the module
    90906p75.jpg






    Fig. 5: Pull the light bulb out from behind the module. Never
    touch the glass of the light bulb
    90906p76.jpg



  5. Detach the headlight electrical connector.
  6. Remove the retaining ring holding the bulb to the back of the headlight
    module.
  7. Pull the bulb from the back of the headlight module. Hold the bulb by its
    base only; try not to touch the glass itself.
    To install:

  8. Holding the bulb by the base, place it in the headlight module, then secure
    with the retaining ring.
  9. Attach the electrical connector to the bulb.
  10. Install the headlight module into the vehicle and tighten the 2 retaining
    screws.
  11. Connect the negative battery cable and check the headlight operation.


Sebring Coupe and Avenger


  1. Open the vehicle's hood and secure it in an upright position.
  2. Disconnect the negative battery cable.
  3. Remove the sealing cover by rotating it counterclockwise.
  4. Remove the bulb attaching spring and pull out the light bulb.





    Fig. 6: Remove the headlight sealing cover(s)
    90906g28.gif






    Fig. 7: Remove the attaching spring and pull out the bulb
    90906g29.gif

    To install:

  5. Install the bulb into the headlight module.
  6. Install the bulb attaching spring.
  7. Install the sealing cover.
  8. Connect the negative battery cable and check the headlight operation.


prev.gif next.gif

Oct 07, 2010 | 1996 Dodge Avenger

1 Answer

How to change right headlight on 2006 chry. sebring


It's very tight under the hood with these cars, you just have to unscrew the two (or three) long bolts holding the entire headlamp enclosure in, pull the headlamp enclosure out and rotate the bulb to remove it. Some sebrings have a cylindrical plastic guard around the main bulb, that just screws off as well. You might have to adjust your headlights after you change them.

Apr 18, 2009 | 2001 Chrysler Sebring

1 Answer

How to change headlight in 2000 chrysler sebring convertible


There is a cover over the bulb that is removed by turning counter clockwise. (as viewed from the back of the housing)
Remove the spring clip that holds the bulb and pull out bulb.
Plug in new bulb (do not touch glass with hands) and install re-install spring clip and back cover.

Mar 15, 2009 | 2000 Chrysler Sebring

2 Answers

Replacing headlight bulbs on a 2006 chrysler sebring


Behind the headlight you should see a eletrical wires running to the headlight section. There will be a 2 inch round plastic ring. You grap the back of the bulb and turn it to the right which will release the bulb and the socket. You pull out the bulb and replace it the same way. If this doesnt help then get back to me.

Feb 06, 2009 | 2006 Chrysler Sebring

1 Answer

Dashlight location for a 1999 sebring convertible


Not usualy 1 single bulb but a number of them.Not usual that they all stop working have you checked that the dimmer light hasnt been moved?If no luck with dimmer youll have to remove dash to change the bulbs.Anyway good luck and happy new year.

Dec 29, 2008 | 1999 Chrysler Cirrus

1 Answer

Changing low beam headlight bulb on 2005 chrysler sebring


you can change the passanger side with little difficulty however the drivers side you need to remove power cell from it's bracket and move aside in order to access light.

Nov 12, 2008 | 2005 Chrysler Sebring Conv

Not finding what you are looking for?
2004 Chrysler Sebring Logo

1,474 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

64052 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...