Question about 2000 Hyundai Accent

1 Answer

Won't go will not go into gear 1st or reverse, seems like the brakes are on clutch doesn't seem like it is working

Posted by on

  • gustavplate Aug 03, 2008

    wont go shift to any gear and does not move

  • Eric kaiser May 11, 2010

    will the car go into any gears?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 53 Answers

Here is a way to diagnos the problem with the car not running shift into forward or reverse depress clutch pedal and turn ignition to start and back (be careful the car will most likely move forward or back alittle depending on the gear) if the car moves u deffinatly have a clutch system problem not nessesarly the clutch though

Posted on Oct 19, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

I have a 2001 elantra. What would make it stay in reverse and 1st gear.it is a manual transmission


when you put it in reverse,first thing you feel a spring.after tthat you lift,
a security plate,this plate prevent you from going reverse into 1 gear.
cause the axel turn a little further when you allreddy has stop the car.
this takes two sec.thats why when putting it in reverse after you feel the spring you wait two seconds,then puch al the way in reverse.

Jul 26, 2014 | 2001 Hyundai Elantra

1 Answer

Engine revs but no acceleration


Clutch plate and pressure plate seem to be too weak to pull the car. Or one of the CV joints is detached from the gear box. To test the clutch plate, park the car on flat surface. Pull the hand brake up, start the car, depress the foot brake pedal, depress the clutch pedal, put the car in 1st gear, press the gas pedal and leave the clutch pedal at once, while keeping the brake pedal depressed.
Follow one of the two following statements:
1. Engine does not shut down and remain start. (Clutch plate, pressure plate and clutch bearing defective - Replace all as a set)
2. Engine shuts down. (Clutch system is OK and does not require any repair).

May 22, 2013 | Honda Civic Cars & Trucks

2 Answers

My clutch won't engage 1997 Honda civic


Clutch plate and pressure plate seem to be too weak to pull the car. To test the clutch plate, park the car on flat surface. Pull the hand brake up, start the car, depress the foot brake pedal, depress the clutch pedal, put the car in 1st gear, press the gas pedal and leave the clutch pedal at once, while keeping the brake pedal depressed.
Follow one of the two following statements:
1. Engine does not shut down and remain start. (Clutch plate, pressure plate and clutch bearing defective - Replace all as a set)
2. Engine shuts down. (Clutch system is OK and does not require any repair).

Apr 06, 2013 | 1997 Honda Civic

1 Answer

Won't go back


If your vehicle is fitted with automatic gear box sounds that you are going to loose the transmission.For not going on reverse like having locked wheels,I believe looks like the brake bands in the gear box are the reason and the minimal power you have for forward drive are the clutches which are slipping. Visit an experts shop and please do not force it.

Aug 16, 2012 | 1999 Toyota Camry

1 Answer

Kia sephia will start but when lights turned on door locks and starter motor engage?


you have wires reversed at the fuse block under hood, matbe had to replace sone of the maxi fuse's that bolt in?? the clutch is probable bad there is a test motor running emergency brake on then push clutch pedal in and try 1st gear and keep pedal down during this, go 1st gear the to reverse if wont go smoothly or grinds then most likly clutch throwout bearing is bad, maybe clutch cable is streched or not adjusted properly if it is mechanical clutch, depends on year and engine size

Jul 15, 2012 | 2001 Kia Sephia

3 Answers

Hard to shift my gears when car in cold.Won't even go out of neutral to 1st gear.Forget about going into reverse.


With the engine off, check your operation of the gear shift. If you can go in and out of the gears fine without the engine running, then you have a worn clutch disc that needs replaced. If the problem still exists then you either have low fluid/weak hydraulic system, or there is a problem with the syncro that may be adjusted.

Nov 02, 2011 | 2006 Ford Focus

1 Answer

Seems to be missing reverse and wont take off in 1st.


apply brake many time make sure the lights indicator is off when you apply. check brake light S.w
check rear brake light working while you apply brake .if manual gear box replace presure plate and clutch

Jul 04, 2011 | 1985 Volkswagen Cabriolet

1 Answer

Reverse doesn't work


Worn clutch plates. Reverse & first gear uses the same clutches so how is 1st gear running out as you drive off? Slips a little?

May 24, 2009 | 1993 Toyota Camry V6

Not finding what you are looking for?
2000 Hyundai Accent Logo

Related Topics:

348 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...