How do i lower the spare tire on a 2004 Iszuzu asender

Since the spare is mounted under the rear of the car, Its not easy...you have to assemble the long crank rod out of its two pieces, then feed the rod through the hole in the top of the rear bumper and lock it into the mechanism that holds the tire in place. Once the crank rod is locked in, lower the tire towards the ground. Once the tire is low enough, you can crawl under the car and release the tire from its mount. The hardest part is locking the crank rod into the spare tire mechanism through the hole in the bumper.

the cable lowers all the way through the tire and makes it to the ground?
The tire must be stuck on something, try to get up under there and see whats going on.

hope you figure it out.

Happy trails.

Find a plastic cover located in the carpet at the back right corner. Lift the cover to locate a nut the size of a lugnut of your tires. Using the van's lugnut wrench, turn nut counter-clockwise to lower the spare tire. Have fun and don't pinch yourself while removing the tire.

Rotate the hoist shaft counterclockwise in order to lower the spare tire to the ground. Continue to rotate the shaft until the spare tire can be pulled out from under the vehicle and removed. If the spare tire does not lower to the ground, the secondary latch is engaged causing the tire not to lower.

If the secondary latch is engaged and the cable end is visible, perform the following procedure: 3.1. Tighten the cable by rotating the hoist shaft clockwise until you hear 2 clicks or feel it skip twice. You cannot overtighten the cable. 3.2. Loosen the cable by rotating the hoist shaft counterclockwise 3 or 4 turns. 3.3. If the spare tire can be lowered, repeat steps 1 and 2 to see if the spare tire can be removed. 3.4. If the spare tire cannot be lowered, rotate the hoist shaft counterclockwise until approximately 15 cm (6 in) of cable is exposed. 3.5. Raise and support the vehicle. 3.6. Place a transmission jack, or equivalent, under the spare tire. 3.7. Position the center of the transmission jack under the secondary latch release button at the center of the spare tire. Arrange the arms of the transmission jack so they will support the tire after it has been released. 3.8. Raise the jack until the spare tire stops moving upward and is firmly held in place, releasing the secondary latch. 3.9. Lower the tire. If the spare tire is hanging by the cable, rotate the hoist shaft counterclockwise until the tire is low enough to remove.

U need the special wrench to lower the spare, there is no other way since the cable hoist is under the spare tire.

On my 2004 toyota,,,directly behind the passenger side front seat (have to push passenger seat all the way forward to see it, there is a small square flap in the carpet,,,lift that up and underneath is a big bolt which you turn counterclock wise with your spare tire lug wrench and the tire will lower to the ground. thats about it. good luck

The tools are under the second row seats. The hole for the spare tire lowering mech. is above the rear bumper when you lift the tail gate. Put the proper tool down the hole, turn counter clockwise, lowers spare. Reverse to bring up.

First off did you Know this ?????

Make / Models : Model/Build Years:
GMC / 1500 2004
Regency / Chevrolet 1500 2004
MANUFACTURER: General Motors Corp.
NHTSA CAMPAIGN ID Number : 04V240000 Recall Date : MAY 14, 2004
COMPONENT: Tires: Temporary/Emergency Spare Tire
Potential Number Of Units Affected : 285
SUMMARY:
The spare tire and wheel assembly that was provided on certain conversion vehicles will not fit on the front wheel hub due to offset of the wheel. However, it will fit on the rear wheels.
CONSEQUENCE:
If someone has a flat tire on the front wheel, they will not be able to install the provided spare tire.
REMEDY:
Dealers will install a spare wheel with the correct offset. Owner notification began on June 11, 2004. Owners should contact Regency at 1-800-989-4727.
NOTES:
Customers can also contact The National Highway Traffic Safety Administration's Auto Safety Hotline at 1-888-DASH-2-DOT (1-888-327-4236)

SPARE TIRE is Under rear of truck use Long Cranking in HoleClose to Lisence Plate to Lower it Down Cranking Counter Clockwise. Wing in center of Wheel pokes thrugh Hole in Center of wheel
Reverse Procedure to Put old tire in Tire Storage Compartment

1. Locate Jack & Wheel Lug Nut Wrench
2. There is Directions as to where to placse the Jack for raising Truck Where Jack is Located
3. Set Park Brake Chalk tire if possible & Hazard lights (If on the Roadside)
4. Loosen all Wheel Nuts on said wheel before Raising Vehicle
5. Place Jack In Recomended Placment spot
6. Rear is Normaly on Axel close to Shock
7. Front is Normaly on FRAMERAIL
8. Raise vehicle untill tire is 3-4 inches off ground as Flat will Lower vehicle
9. Remove All Wheel Nuts And Wheel
10. Place new wheel/tire on Vehicle and start all nuts
11. Tighten nuts as tight as Possible then Lower Vehicle Untill tire touches ground Good
12. Now Toque Wheel Nuts as tight as Possible with hand tool
13. Lower vehicle all the way down
14. Put away tools and Reliece Park Brake
15. Torque should be around 100-130 foot Pounds

I Hope this is What You Wanted Its Off the Cuff as My Reference Books done have this Procedure.

your post was cut short, but cable that holds the spare in place is what I think u were asking, and that would be what u call it, 'the cable that secures the spare tire, or lowers the spare tire'

The spare is held in place by a cable hoist, the the tool kit for changing tires has the crank to lower the spare. the access hole is through the bumper in most cases, look under the rear bumper u will see the crankin down access easily that way.