Question about 2004 Nissan 350Z

1 Answer

Wheel nut torque settings

What is the torque settings for my wheel nuts

Posted by on

  • Anonymous Mar 17, 2014

    torque settings for nuts connecting fuel pump to fuel rail

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 726 Answers

65 ft/lb? And tighten 1 3 5 2 4

Posted on Jul 15, 2008

6 Suggested Answers

  • 1 Answer

SOURCE: Torque specs for front wheel hub nut

112 to 174 ft lbs

Posted on Apr 04, 2009

goofduck
  • 490 Answers

SOURCE: What is the exact wheel nut torque

Vibe 2003-05 75 ft-lbs

Posted on Apr 21, 2009

  • 101 Answers

SOURCE: Torque setings

if it is a solid bearing do it up as tight as you can.if it is a tapered bearing do it up untill the nut is touching the bearing check the hub for play if you have got play do the nut up a bit more until the play is gone in the hub.make sure you do not over tighten the bearing or the wheel will not turn freely.the wheel needs to spin with no drag.

Posted on Jul 31, 2009

  • 583 Answers

SOURCE: need torque setting for 1993 geo tracker front

i1m sorry to say that wheel bearings are not set to a torque specification, when you have repacked the bearings [ inner and outer ] ,reassembled it ,take the nut up until thewheel starts to drag and not turn very far when you try to spin it spin it backward and forward several times,grab the top of the wheel and try to push it in and out,if you getany movement at all tighten the nut a couple of castilations. do it all over again, spinthe wheel a few times and then try for the crossways movement again, if there is no movement ,you are very close to being right....................now comes the experience bit , iwould take it one more castilation of the nut because i know the feel that is need ed,,without that i suggest you put the pin in where you ereput the cap on and go for a 5 minute drive . whenyou get back ,jack it up and thespinning of the wheel again and try for the top crossways movement ,if there is any tighten thenut 2 castilations, and provided that when you try to spin the wheel by hand with a reasonably strong push the wheel should trael about 6 inches at least after your hand leaves it ,it is now a close as you are going to get itput it all to gether and for the next day or so put yor hand on the grease cap after you have driven anydistance, and you will feel it is warm but you should be able tohold your hand on the grease cap. there you have it ,any questions come back."youdoit"

Posted on Nov 06, 2009

  • 88 Answers

SOURCE: ford focus wheel nut torque setting for alloy

hi we set them at 100nm which is tight enough and all so tight enough so you can undo them at the side of the road if you need to regards

Posted on Jan 21, 2010

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2001 GMC Seirra Truck 4wheel drive 5.3L. Torque specs for lug nuts?


2001 GMC Truck Sierra 1500 4WD 5.3L SFI 8cyl

The Lug Nut Tightening Torque 140 Foot pounds (Final torque).

Oct 06, 2015 | GMC Cars & Trucks

1 Answer

Torque setting for wheel nuts on Renault Alloy wheels


130(NM) 96 ft/lbs is the torque setting for a 2008 renault scenic so as not to ruin studs or brake rotors should be sufficient for allloys just need to check alloy lug nuts more often

Aug 09, 2014 | Renault SCENIC Cars & Trucks

2 Answers

What is the torque setting for my alloy wheels?


Your torque spec is usually based off of lug diameter, if you have 19mm lug nuts then 75#ft should be sufficient.

Aug 09, 2014 | 2007 Renault Scenic 1.5

2 Answers

Lug nut torque chart


Here's a handy link to the wheel nut torque settings for hundreds of different vehicles.
Look your's up........and away you go!
http://www.discounttiredirect.com/infoCenter/infoWheelTorque.html

Jul 30, 2014 | 2004 Pontiac Montana

2 Answers

What is the torque setting for the front wheel bearing of a 2000 Grand Am


the nut with the caged affair around it (1st design) has torque of 284 ft/lbs yip! that's right.
The second design is a regular nut with a torque of 173 ft/lbs.

Hope that helps.

Aug 06, 2011 | 2000 Pontiac Grand Am GT

1 Answer

Procedure for replacing rear whl brgs on a 2003 escape awd


4-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake shoes
    • Rear halfshaft nut and loosen the halfshaft from the hub
    • Wheel hub and place it in a vise
    • Inner wheel bearing race from the hub
    • Antilock Brake System (ABS) sensor bracket and move the sensor aside, if equipped
    • Parking brake cable from the steering knuckle
    • Brake line from the wheel cylinder and support the knuckle
    • Lower shock absorber nut
    • Lower ball joint by holding the ball joint stud
    • Upper ball joint
    • Coil spring while noting the location of the insulator
    • Steering knuckle cam
    • Steering knuckle
    • Snapring and press out the outer wheel bearing race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge

To install:

  1. Install or connect the following:
    • New wheel bearing into the steering knuckle
    • Snapring to the knuckle
    • Wheel hub
    • Steering knuckle cam and hand tighten the bolt
    • Coil spring
    • Shock absorber lower nut. Torque the nut to 85 ft. lbs. (115 Nm) for 2002-04 models; 129 ft. lbs. (175 Nm).
    • Upper ball joint. Torque the nut to 76 ft. lbs. (103 Nm).
    • Lower ball joint. Torque the nut to 76 ft. lbs. (103 Nm). Align the steering knuckle cam and torque the bolt to 85 ft. lbs. (115 Nm).
    • Brake line to the wheel cylinder. Torque the brake line bracket bolt to 15 ft. lbs. (20 Nm) and the brake line fastener to 11 ft. lbs. (15 Nm).
    • Parking brake cable to the backing plate. Torque the bolt to 16 ft. lbs. (22 Nm).
    • ABS sensor bracket. Torque the bolt to 80 inch lbs. (9 Nm), if equipped
    • Halfshaft nut. Torque the nut to 214 ft. lbs. (290 Nm).
    • Brake shoes
    • Rear wheel
    • Negative battery cable
  2. Fill and bleed the brake system.
  3. Check and adjust the wheel alignment as needed.

2-Wheel Drive
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Rear wheel
    • Rear brake drum
    • Wheel hub nut
    • Wheel hub
    • Inner wheel bearing race from the hub
    • Snapring
    • Wheel bearing outer race from the knuckle
      06017-esca-g92.gif

      Rear hub and bearing
      Click to Enlarge 06017-esca-g93.gif

      Rear hub removal
      06017-esca-g94.gif

      Inner wheel bearing removal-rear hub/bearing
      06017-esca-g95.gif

      Rear wheel bearing removal-2wd
      06017-esca-g96.gif

      Rear wheel bearing removal-4wd

To install:
Install or connect the following:

  • Wheel bearing in to the knuckle
  • Snapring
  • Wheel hub into the wheel bearing
  • Wheel hub nut. Torque the nut to 214 ft. lbs. (290 Nm).
  • Brake drum
  • Rear wheel
  • Negative battery cable
    06017-esca-g97.gif

    Rear wheel bearing installation
    06017-esca-g98.gif
    hope this helps if so send testimonial comment or even any other questions you have

Jan 16, 2011 | Ford Escape Cars & Trucks

1 Answer

TORQUE SETTING ON FRONT WHEEL BEARING NUT ON 2006 PONTIAC TORRENT


Hello, here is the torque spec for front hub bearing
Strut to Steering Knuckle Bolt and Nut
180 N·m
133 lb ft
Tie Rod Retention Nut
50 N·m
37 lb ft
Wheel Bearing/Hub Mounting Bolt
130 N·m
96 lb ft
Wheel Drive Shaft Spindle Nut
205 N·m
157 lb ft

Nov 07, 2010 | 2006 Pontiac Torrent

1 Answer

Need the 2000 Buick LeSabre rear wheel Hub nut torque spec.


Those are not nuts, they are bolts. The torque spec for those bolts is 52ft.lbs

Jul 12, 2009 | 2000 Buick LeSabre

Not finding what you are looking for?
2004 Nissan 350Z Logo

2,497 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...