Question about Chevrolet Chevy

Open Question

Service Tire Monitor system is on and wont reset

Posted by on

  • 2 more comments 
  • popcorn17201 Sep 27, 2008

    my service tire monitor system wont reset

  • Sutton 20 Nov 29, 2008

    I have a problem , the "Service tire monitor system" message comes up on my Chevrolet 2006 Impala message center. The tire pressure shows on 3 of the tires and on one it shows nothing but the air is fine in the tire. What can I do without taking care to dealer for service.

  • Anonymous Dec 26, 2008

    Just installed 24 inch rims on my 2wd 2008 silverado and service tire monitor system warning came on how can i reprogram computer to regonize new after market rims without sensors.

  • peskhs Jan 25, 2009

    Ditto

×

5 Suggested Answers

  • 840 Answers

SOURCE: Service Tire Pressure System - Chrysler 300M 2002

try disconnecting the battery for 15-20 minutes then check again/ Please rate my response thank you very much

Posted on Feb 01, 2009

Tech jk
  • 102 Answers

SOURCE: my car has been telling me to service my tire monitor system

The service tire monitor warning can come on for many reasons. A sensor may have gone bad, may have been broken if a tire was changed recently, the car needs an updated module and antenna. The system woiuld need to be looked at by a technician.

Posted on Jul 04, 2009

  • 1 Answer

SOURCE: resetting "service tire monitor" light on 2004 silverado

Did as you  said IT WORKS GREAT NO MESSAGE  Thanks 

Posted on Feb 18, 2009

  • 4 Answers

SOURCE: Tire monitor reset 1999 Corvette

You can do this if you have a strong magnet. Go through the options menu until the screen is clear with the key on engine off. Then hold the reset button until it says key fob learn. I think it was the e/m button I hit to go to the next screen. Then it has the tire relearn procedure. It will tell you which tire to put the magnet on. Place magnet by the valve. it should beep. go to each tire in the order it tells you and you're done.

Posted on Sep 01, 2009

mabpest
  • 1152 Answers

SOURCE: I just bought a 2008

you have a low tire...the vehicle has a sensor to read the tires pressure..just air tires up to recommended pressure and light will go off.

Posted on Feb 09, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get the service tire monitor system light to go off


could be that the new tires are putting the parameters out side that set for the sensor
you may have to find a shop that can reset the computer for the bigger wheels

Feb 07, 2016 | Cars & Trucks

1 Answer

How to reset the check tire pressure indicator


Using the Driver Information Center (DIC)
Important: After resetting, the tire pressure monitoring (TPM) system requires up to 8 km/h (5 miles) of flat, smooth road straight line driving in each of the 4 speed ranges to complete the calibration process. For further information, refer to Tire Pressure Monitor Description and Operation . If the TPM system does not reset, refer to Driver Information Center (DIC) Switch Inoperative .
  1. Set all tire pressures to the recommended kPa/psi. Refer to Vehicle Certification, Tire Placard, Anti-Theft, and Service Parts ID Label .
  2. Turn ON the ignition, with the engine OFF.
  3. Press the vehicle information button until TIRE INFLATION MONITOR SYSTEM PRESS (down/left arrow) SWITCH TO RESET is displayed.
  4. If the system is being reset due to a low tire pressure condition, press and hold the down/left arrow button until TIRE INFLATION MONITOR SYSTEM HAS BEEN RESET is displayed. If the system is being reset due to a tire rotation, press and hold the down/left arrow button for 5 seconds.
  5. Release the down/left arrow button and TIRE PRESSURE NORMAL is displayed.

Oct 08, 2015 | 2006 Pontiac Grand Prix

1 Answer

Service tire monitor systems


Tire Store---- to have the sensor replaced in the wheel
or the system reset

Owners manual may tell you something about resetting,if you
rotated your tires to other positions, or it may not

You do not need a dealer for ANY Vehicle work-- as the manual tells you

Jul 25, 2014 | Cars & Trucks

3 Answers

My low tire light came on so I went and had air and all the tires checked but now I don't know how to turn the light off. I have had the car since 2000 and it has 50,000 miles on it but could never figure...


Hello Mattingly.

Here is some information for you regarding your problem.

The Tire Inflation Monitor (TIM) system alerts the driver when the pressure changes in one of the tires. The system only detects a low pressure condition while the vehicle is being driven. Once a low tire pressure condition is detected, the system informs the driver that a low tire pressure condition exist's, whenever the ignition is ON.
The LOW TIRE message appears on the Instrument panel if the tire pressure in one tire becomes at least 82 kPa (12 psi) lower or higher than the other three tires. The message does not appear if more than one tire is low or high, or if the system is not calibrated properly. The system does not inform the driver which tire is low. To clear this message, set the tire pressures in all four tires to the proper pressures and perform the system reset procedure. Refer to Tire Inflation Monitor Reset Procedure for service procedure.
The Tire Inflation Monitor software requires approximately one half hour of straight line driving to complete the TIM autolearn. There are several speed ranges that the EBCM needs to learn the tire inflation configuration in order to have the full capability of detecting a low tire condition. The speed detection ranges are the following:

  • 24-64 km/h (15-40 mph)
  • 64-113 km/h (40-70 mph)
  • 113-145 km/h (70-90 mph)
Each speed range has 2 modes of low tire detection.

  • Monitor Mode 1
  • Monitor Mode 2 The EBCM learns the tire inflation configuration for each speed range independently. In Monitor Mode 1, the EBCM has only partially learned the tire inflation configuration for the speed range and has limited detection capability for a low tire condition. In Monitor Mode 2, the EBCM has fully learned the tire inflation configuration for the speed range and has full detection capability for a low tire condition. If the EBCM is not in Monitor Mode 1 or Monitor Mode 2, a low tire condition cannot be detected because the EBCM has not learned the tire inflation configuration of the vehicle.

To reset (calibrate) the system:
Turn the ignition switch to RUN. Then press and hold the RESET button for about five seconds. The red RESET button is located inside the instrument panel fuse block on the right side of the dash.. The LOW TIRE light will come on and flash three times and then it will turn off.
The system completes the calibration process during driving.
The system normally takes 15 to 20 minutes of driving in each of three speed ranges to "learn" tire pressures. The speed rages are 15 to 40 mph (25 to 65 km/h), 40 to 65 mph (65 to 105 km/h) and above 65 mph (105 km/h).

There you are, this should fix you up.
Keep in mind this system uses wheel speed sensors to calculate. If one of your sensors isn't working your low tire light will remain on.

Thank you for using FixYa.

KL

Jan 20, 2011 | 2000 Buick Century

1 Answer

Had a low tire and service tire monitor came on


chevrolet usually resets itself after the problem is fixed. unless it is a bad sensor on one of the wheels. also check the spare some spares have a monitor in them.

Aug 25, 2009 | 2004 Chevrolet Silverado 3500

2 Answers

Punctured tyre warning indicator


use the I drive system to reset flat tire monitor, go to vehicle settings, then flat tire monitor, then select reset, then you have to drive the car system resets as you drive

May 23, 2009 | 2002 BMW 5 Series

1 Answer

Tire pressure reset will not reset


Labatche822,
The process for resetting your Tire Pressure Monitor (TPM) is below.
Good luck, let me know.
Regards.

To reset (calibrate) the system:
1. Turn the ignition switch to RUN.
2. Press the GAGE INFO button on the DIC until
TIRE PRESSURE appears on the display.
3. Press and hold the DIC RESET button for about five
seconds. After five seconds, the display will show
TIRE PRESSURE RESET. If TIRE PRESSURE
RESET does not appear on the display after about
five seconds, see your dealer for service. After you
release the DIC RESET button, TIRE PRESSURE
NORMAL will appear on the display.
The system completes the calibration process during
driving. During the first 10 to 25 miles (15 to 40 km) of
driving, the system will not alert you if a tire is high or
low. After 25 to 100 miles (40 to 160 km), the
system will only alert you about pressure differences of
12 psi (85 kPa) or more. After about 100 miles (160 km)
of driving, the system will alert you if one tire is
10 psi (69 kPa) different from the other three tires.

May 04, 2009 | 1999 Buick Park Avenue

1 Answer

My car has been telling me to service my tire monitor system


The service tire monitor warning can come on for many reasons. A sensor may have gone bad, may have been broken if a tire was changed recently, the car needs an updated module and antenna. The system woiuld need to be looked at by a technician.

Apr 24, 2009 | 2005 Chevrolet Impala

1 Answer

Changing to winter tires


Sounds like you just need to reset the tire pressure system. It won't hurt to drive. Check your owner's manual on how to reset, or ask your dealer.

Nov 19, 2008 | 2008 Chevrolet Express

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

2,413 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...