Question about Saturn SC1

1 Answer

Cylinder 1 misfire - SC1 Saturn Cars & Trucks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 13 Answers

Read my solution to Eromrab who had " Lots of problems...
His problem is dated August 8th.

Posted on Aug 12, 2008

  • ttyers Nov 03, 2010

    Can't find solution to Eromrab who had " Lots of problems...

×

5 Suggested Answers

jamaicanmech
  • 17 Answers

SOURCE: Cylinder #1 misfire on a Ford Taurus SHO

do a compression check. if you have a low compreeion reading below 80psi you need to do a head job. question is the iol milky on the dip stick?

Posted on Jan 08, 2009

roedmondson
  • 68 Answers

SOURCE: 2000 CIVIC System too lean Cylinder 3 and 4 misfire Deteced

  1. P0171: This means that the oxygen sensor has detected a lean air-fuel ratio. This can be caused due to a vaccuum leak or a problem in the HO2S circuit or the HO2S (Heated Oxygen Sensor) itself. (Bank one Sensor one). This is commonly located along the exhaust pipe. It could also be a bad Mass Air Flow sensor or a bad Engine Coolant Temperature sensor. Diagnostic checks will be needed to be carried out to be verified though
  2. Well as for the other codes, it means #3&4 cylinders are misfiring. It is a possibility that the P0171 code mite have caused the others to show up. I can be wrong though. But it is a strong possibility. If the air fuel mixtue is too lean indeed, mis-firing will occur, unless it is an actual electronic and not a mechnical problem. By the way, when these codes appear, how is the engine's performance. Does it remain the same or behaves poorly?

Posted on Feb 14, 2009

Molson02536
  • 3854 Answers

SOURCE: code 301, random or cylinder 1 misfire

Spake pluge could have gone bad, or the Spark Plug wire. Try changing all your plugs and wire and inspect the old one's. The wire could be bad do to time or may have been against the exhaust manifold and brunt. Good luck

Posted on Apr 08, 2009

  • 119 Answers

SOURCE: MISFIRING ON CYLINDER 1 VW POLO 1.4 3CYLINDER

I have changed a few cylinder heads under warranty for this type of problem. The exhaust valve guides wear, this causes the exhaust valve to seat badly, giving low compression. if one cylinder compresion reading is more than about 50 psi below the others, then this warrants head removal. It is quite a job, due to the fact that the camshft id chain driven. If you are up for it then once the head is removed, poor liquid into the exhaust ports and see if it leaks out through any of the exhaust valves.

Posted on Jul 23, 2009

GARYca
  • 672 Answers

SOURCE: misfire #1 cylinder (autozone scanner) I changed

inspect the sparkplug plug first!! After engine is running for 20 sec (while misfiring), pull your #1 sparkplug and check for fuel. If there is no fuel replace the injector!!If there is fuel, post a comment for more help!!

Posted on Sep 01, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

#1 cylinder is misfiring, put new fuel ejector and the problem is still there.It has a bad noise in the motor.


Thread: Cylinder 1 misfire P0301 - The Chrysler Minivan Fan Club ...

forum.chryslerminivan.net/showthread.../27978-Cylinder-1-misfire-P03...

Feb 6, 2013 - 7 posts - ‎4 authors
My mother-in-law's 2002 Town and Country has the P0301 cylinder 1 misfire error code. I haven't done much work on this type of car, so I'm not ... '05 Town & Country Cylinder 1 misfire mystery
10 posts
Feb 3, 2014
Engine misfire
7 posts
May 6, 2012
#1 Cylinder misfires at idle only
10 posts
Jun 4, 2011
Running rich / Misfire Mystery
10 posts
Sep 20, 2010
More results from forum.chryslerminivan.net

Part 1 -How to Test the Coil Pack (2001-2008 Chrysler 3.3L ...

easyautodiagnostics.com > Chrysler > 3.3L, 3.8L
Apr 29, 2011 - Page 1 of 7: How to Test the Coil Pack (2001-2008 Chrysler 3.3L, 3.8L). ... This article will help you troubleshoot a Misfire Condition that might be setting ...your 2001-2009 Chrysler (or Dodge) 3.3L or 3.8L Town and Country, Voyager, ... it's important the you know what 'Paired Cylinders' and 'Non-Paired ...

Jan 03, 2016 | 2001 Chrysler Town & Country

1 Answer

Check engine light code p2196,p2197, po300 ,304,305,306,p2 ,Im freeking out.


P0300 Random/Multiple Cylinder Misfire Detected P0301 Cylinder 1 Misfire Detected P0302 Cylinder 2 Misfire Detected P0303 Cylinder 3 Misfire Detected P0304 Cylinder 4 Misfire Detected P0305 Cylinder 5 Misfire Detected P0306 Cylinder 6 Misfire Detected P0307 Cylinder 7 Misfire Detected P0308 Cylinder 8 Misfire Detected P0309 Cylinder 9 Misfire Detected P0310 Cylinder 10 Misfire Detected P0311 Cylinder 11 Misfire Detected P0312 Cylinder 12 Misfire Detected P0313 Misfire Detected with Low Fuel P0314 Single Cylinder Misfire (Cylinder not Specified) P0315 Crankshaft Position System Variation Not Learned P0316 Misfire Detected On Startup (First 1000 Revolutions)

Read more at: http://www.obd-codes.com/trouble_codes/
Copyright © OBD-Codes.com
-----------------------------------------------------------------------
P2195 O2 Sensor Signal Stuck Lean Bank1 Sensor 1 P2196 O2 Sensor Signal Stuck Rich Bank1 Sensor 1 P2197 O2 Sensor Signal Stuck Lean Bank2 Sensor 1 P2198 O2 Sensor Signal Stuck Rich Bank2 Sensor 1

Read more at: http://www.obd-codes.com/trouble_codes/
Copyright © OBD-Codes.com http://www.obd-codes.com/p0002

May 07, 2015 | 2006 Ford Taurus SEL

1 Answer

2003 acura tl error codes po301 po302 po304 po306 p1399 po300


PO300 and P1399 are random cylinder misfire detected.
PO301 cylinder 1 misfire
PO302 cylinder 2 misfire
PO304 cylinder 4 misfire
PO306 cylinder 6 misfire
I would say that you have damage to the ignition wiring harness or you ECM is failing.

Feb 17, 2015 | Acura Cars & Trucks

1 Answer

I would like to know what these codes mean


P0171 System Too Lean (Bank 1)
P0174 System Too Lean (Bank 2)
P0301 Cylinder #1 Misfire Detected
P0302 Cylinder #2 Misfire Detected
P0304 Cylinder #4 Misfire Detected
P0306 Cylinder #6 Misfire Detected

Mar 12, 2014 | 1999 Ford Explorer

1 Answer

PO016, PO300, PO420, PO442 codes


your engine is misfiring according to your codes ...4 codes 4 problems
P0300 - Random Cylinder Misfire DetectedP0301 - Cylinder 1 Misfire DetectedP0302 - P0312 Cylinder X Misfire DetectedP0325 - Knock Sensor 1 Circuit (Bank 1)Just showing a few

Oct 23, 2013 | 2003 GMC Envoy

1 Answer

Cylinder misfire


misfire,
only on cylinder #1
bad spark plug or wires to it or COP coil to it.
bad injector
bad injection signals
low compression on #1

there are simple tests for each, i will not ever guess on misfire.

misfire means, in English (not slang)
THIS Cylinder #1 had weak power during the POWER stock.
The ECU computes Velocity of each power stroke and Reports the weak.
even an air leak to #1 intake runner can cause this
or the injector #1 base gasket leaking. Air.

but it is not fibbing it is weak. #1

Oct 20, 2013 | 1996 Chrysler Cirrus

3 Answers

CODES-PO301-PO303-PO316- CHANGED PLUGS & WIRES. STILL MISS ON START UP, GOES AWAY MOST OF THE TIME ABOVE 1000 R.P.M


P0301 - Cylinder 1 Misfire Detected.

Causes:
- Improper spark plug at cylinder #1
- Insufficient compression at cylinder #1
- Incorrect fuel pressure
- The injector circuit is open or shorted at cylinder #1
- Fuel injector #1 may be faulty
- Intake air leak

Solutions:
- Perform Injector Service
- Replaced Spark Plug #1
- Replaced Injector #1
- Replaced Ignition Coil #1

P0303 - Cylinder 3 Misfire Detected.
Follow info from P0301.

P0316 - Misfire Occurred In The First 1,000 Engine Revolutions.

Causes:
- Damaged CKP sensor.
- Ignition System.
- Fuel Injectors
- Running out of fuel
- Fuel Quality
- Base engine
- Damaged Powertrain Control Module

Solutions:
Usually the P0316 is combine with a P03XX codes. The P03XX code indicates in which cylinder the misfire occurred.

Jan 17, 2011 | 2002 Mercury Sable

2 Answers

05 kia amanti with diagnostics codes p0350,p0320,p0300,p0302,p0303,p0304,p0305,p0306.skipping at times.when it does skip & misfire the rpm gauge goes crazy.this problem is not consitant


Generic OBD II Diagnostic Trouble Codes

DTC CODES P0300 to P0399

P0300....Random/Multiple Cylinder Misfire Detected

P0301....Cylinder 1 Misfire Detected

P0302....Cylinder 2 Misfire Detected

P0303....Cylinder 3 Misfire Detected

P0304....Cylinder 4 Misfire Detected

P0305....Cylinder 5 Misfire Detected

P0306....Cylinder 6 Misfire Detected

P0307....Cylinder 7 Misfire Detected

P0308....Cylinder 8 Misfire Detected

P0309....Cylinder 9 Misfire Detected

P0310....Cylinder 10....Misfire Detected

P0311....Cylinder 11 Misfire Detected

P0312....Cylinder 12 Misfire Detected

P0313....Misfire Detected with Low Fuel

P0314....Single Cylinder Misfire (Cylinder not Specified)

P0320....Ignition/Distributor Engine Speed Input Circuit

P0321....Ignition/Distributor Engine Speed Input Circuit Range/Performance

P0322....Ignition/Distributor Engine Speed Input Circuit No Signal

P0323....Ignition/Distributor Engine Speed Input Circuit Intermittent

P0324....Knock Control System Error

P0325....Knock Sensor 1 Circuit (Bank 1 or Single Sensor)

P0326....Knock Sensor 1 Circuit Range/Performance (Bank 1 or Single Sensor)

P0327....Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)

P0328....Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)

P0329....Knock Sensor 1 Circuit Input Intermittent (Bank 1 or Single Sensor)

P0330....Knock Sensor 2 Circuit (Bank 2)

P0331....Knock Sensor 2 Circuit Range/Performance (Bank 2)

P0332....Knock Sensor 2 Circuit Low Input (Bank 2)

P0333....Knock Sensor 2 Circuit High Input (Bank 2)

P0334....Knock Sensor 2 Circuit Input Intermittent (Bank 2)

P0335....Crankshaft Position Sensor A Circuit

P0336....Crankshaft Position Sensor A Circuit Range/Performance

P0337....Crankshaft Position Sensor A Circuit Low Input

P0338....Crankshaft Position Sensor A Circuit High Input

P0339....Crankshaft Position Sensor A Circuit Intermittent

P0340....Camshaft Position Sensor 'A' Circuit (Bank 1 or Single Sensor)

P0341 Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 1 or Single Sensor)

P0342....Camshaft Position Sensor 'A' Circuit Low Input (Bank 1 or Single Sensor)

P0343....Camshaft Position Sensor 'A' Circuit High Input (Bank 1 or Single Sensor)

P0344....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 1 or Single Sensor)

P0345....Camshaft Position Sensor 'A' Circuit (Bank 2)

P0346....Camshaft Position Sensor 'A' Circuit Range/Performance (Bank 2)

P0347....Camshaft Position Sensor 'A' Circuit Low Input (Bank 2)

P0348....Camshaft Position Sensor 'A' Circuit High Input (Bank 2)

P0349....Camshaft Position Sensor 'A' Circuit Intermittent (Bank 2)

P0350....Ignition Coil Primary/Secondary Circuit

Nov 17, 2010 | Kia Amanti Cars & Trucks

1 Answer

WHAT IS THE CAUSE OF THE PO301 CODE?


The error code p0301 ,This code is related to misfire.The cylinder is misfiring. p0301 this is the indication of cylinder number 1 ,that is misfiring.If the code comes up as p0300 this is the indication of random misfire from all the cylinders.But in your case its indicating p0301 this is indication of cylinder 1 misfire.Check cylinder 1 and replace the faulty cylinder 1 to clear the fault.The spark plugs and the wires connecting to spark plugs also needs to be checked. Keep updated with any more query.Thanks.

Oct 12, 2010 | 2003 Mitsubishi Lancer

1 Answer

I have 1996 Dodge Gran Caravan, and it gives me these codes: 27 and 43, what do they mean??


CODE 27 - Injector Control Circuit, output driver does not respond properly to the control signal

Code 27 MIL light options: OBDII
P0201 - Injector #1 Control Circuit
P0202 - Injector #2 Control Circuit
P0203 - Injector #3 Control Circuit
P0204 - Injector #4 Control Circuit
P0205 - Injector #5 Control Circuit
P0206 - Injector #6 Control Circuit

CODE 43 - Cylinder Misfire, or Ignition Primary Circuit

CODE $# MIL options: OBDII
P0300 - Multiple Cylinder Misfire
P0301 - Cylinder #1 Misfire
P0302 - Cylinder #2 Misfire
P0303 - Cylinder #3 Misfire
P0304 - Cylinder #4 Misfire
P0305 - Cylinder #5 Misfire
P0306 - Cylinder #6 Misfire
P0351 - Ignition Coil #1 Primary Circuit
P0352 - Ignition Coil #2 Primary Circuit
P0353 - Ignition Coil #3 Primary Circuit

Feb 03, 2010 | 1996 Dodge Caravan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

303 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...