Question about 2001 Honda Civic

2 Answers

Winshield washer fluid indicator always on

Fluid level is high and the light remains on, is there a relay or is it just a resistive load at the bottom of the reservoir that gets the light to go off?

Posted by on

2 Answers

Thanks, I didn't know it was a float switch, i'll give it a try!

Posted on Sep 19, 2008

Empty ur fluid box and then pull the float switch or shake it a bit with somehting it will come up and then it will stop working

Posted on Sep 19, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Looking for the fuse for the wiper motor 2008 chevy impala


WPR fuse 25amp under hood fuse box .
Wiper/Washer System Components
The Wiper/Washer System consists of the following components:
• Windshield wiper/washer switch
• Body control module (BCM)
• Wiper PCB relay
• Wiper high PCB relay
• Windshield wiper motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR fuse 25 A
• WSW fuse 10 A
This is more then likely not a fuse issue !!!!!!!
Low Speed Operation
When the wiper switch is in the low speed position, ground is applied through the switch internal resistor and the wiper switch low signal circuit to the body control module (BCM). In response to this signal, the BCM energizes the WIPER PCB relay by applying battery voltage through the wiper relay control circuit to the coil side of the relay. This allows battery positive voltage from the WPR fuse to flow through the switch input side of the WIPER PCB relay and out to the switch input side of the WIPER HIGH PCB relay. Since the wiper high relay is de-energized and its switch contacts are normally closed to the low speed control circuit of the windshield wiper motor, the motor will operate at low speed.
Wiper motor low speed operation and the wiper PCB relay can also be commanded ON/OFF by using a scan tool. Refer to Control Module References.
The PCB relays mentioned above are soldered right into the circuit board inside the fuse/relay block under the hood . There are alot of reasons for the wipers not to work ! The fuse could be blown but fuse's don't just blow for no good reason , short to ground , low resistance high current flow etc.... Intermittant !

Power and Grounds
With the ignition in the ON position, accessory voltage is supplied through the 25A WPR fuse to the WIPER PCB relay, the WIPER HIGH PCB relay and the WS WASH PCB relay that are all located in the underhood fuse block. Refer to Wiper/Washer Schematics.
G200 provides ground for the windshield wiper motor and the WIPER PCB relay. G100 provides ground for the windshield washer fluid pump and the windshield washer fluid level switch.

Dec 04, 2016 | Cars & Trucks

2 Answers

2010 Dodge Grand Caravan break light stays on in dash.


Check the level of your brake fluid or your brake pads may be worn down and time to have them checked out.

Apr 01, 2015 | 2010 Dodge Grand Caravan

1 Answer

Winshield warning light is on in the information center


I have the same jeep it is the washer fluid level. you need washer fluid

Oct 28, 2012 | 1997 Jeep Grand Cherokee

1 Answer

How to replace the winshield washer fluid resevoir 2001 pontiac grand am 3.6L


  1. Remove the left front fender liner.
  2. Remove the air intake duct.
  3. Remove the connector from the washer pump.
  4. Remove the hose from the washer pump.
  5. Remove the connector from the level sensor.
  6. Remove the brake control module.
  7. Remove 3 screws and the washer solvent container from the vehicle.

    Reverse to install.

Oct 17, 2012 | 2001 Pontiac Grand Am SE

1 Answer

2011 Toyota Camry winshield washer fluid light on dashboard won't turn off after filling tank.


The sensor inside the tank is defective or covered in goo. Remove the sensor from the tank or remove the tank and flush it clean with hot water and a mild solution of white vinegar, if the sensor still reads the tank is low replace it.

Sep 25, 2012 | 2011 Toyota Camry

1 Answer

Indicator light


Warning light for battery/charging system usually looks like a battery. check all your fluid levels, including washer fluid. If all fluid levels are OK, and light is still on, take the car to a major auto parts store. They will connect to the cars computer and tell you why the light is on They can also turn it off. This is almost always FREE.

Jun 01, 2012 | 2008 Volkswagen Eos

3 Answers

What does "low wash" mean on a 2007 dodge ram?


This indicates that your windshield washer fluid level is low. It's like the low fuel light, it gives you times to get some before you run out. If you check the washer fluid level and it is not low then the sensor is faulty.

best wishes

Jan 02, 2011 | 2007 Dodge Ram 1500 Quad Cab Sport

3 Answers

Winshield washer fluid will not come out and you can not hear the motor the fuses are fine do I need a new motor for the winshield washer fluid. any advice would be very much appreciated.


WIPER FLUID LEVEL COULD BE LOW. ADD SOME MORE WIPER FLUID.IF FLUID LEVEL OKAY CHECK WIPER SPRAY NOZZLES COULD BE CLOGGED CLEAN THEM WITH A SMALL PIECE OF WIRE SMALL AS TINY PAPER CLIP WHICH CAN BE USED..

Oct 20, 2010 | Pontiac G6 Cars & Trucks

2 Answers

The rear wiper on my '99 model exped isnt working ,ford global says its the motor and it will cost me P13k . any one who can help me find a mechanic do some repair on this?


what is P13K?

check the fuse first. dealer can hook up NGS Tester and get fault codes to see what is wrong.

Principles of Operation
NOTE: The generic electronic module (GEM) will not activate the rear wiper system if either the liftgate or the liftgate glass is ajar. If either the liftgate or the liftgate glass becomes ajar while the rear wiper is in operation, the GEM will park the rear wiper motor.
There are two distinct modes of wiper operation:
  • Off Mode: In this mode, there is no rear wiper activity, and the wiper motor will be in the PARK position.
  • Interval Mode: This mode is selected when the rear wiper switch is in either the Interval 1 or 2 position. When this mode is selected, the rear wiper motor is driven up onto the glass by activating the rear wiper UP relay. When the wiper motor HIGH/LOW/PARK position input reaches the high position, the UP relay is deactivated and the DOWN relay is activated to reverse the wiper motor direction. When the wiper motor reaches the LOW position, as determined by the HIGH/LOW/PARK position input, the GEM deactivates the DOWN relay and will begin a new wiper cycle 1 to 10 seconds later, depending on the interval position selected.
To engage the rear window washer, rotate the rear window washer selector downward to the WASH position. The rear window wiper will run as long as the WASH position is selected. When the rear window washer selector returns to the OFF, INT 1 or INT 2 position, the washer will stop immediately, but the rear window wiper will continue for two to three sweeps and then return to its previous mode of operation.
The low washer fluid indicator chime warns that the washer fluid level is low. The low washer fluid indicator chime is a single tone with a duration of one second. The chime will sound when the low washer fluid indicator is initially activated.
The low washer fluid indicator warns that the fluid level in the washer reservoir is low. The low washer fluid indicator will illuminate when the washer fluid level is low and the ignition switch is in the RUN position.
The low washer fluid indicator will deactivate when the washer fluid reservoir is filled and the ignition switch has been cycled from RUN to OFF, then to RUN.
Inspection and Verification
  1. The wiper/washer system is a generic electronic module (GEM) controlled system; refer to Section 419-10 .
  1. Verify the customer concern by operating the wiper/washer system.
  1. Visually inspect for obvious signs of mechanical and electrical damage.


Visual Inspection Chart Mechanical Electrical
  • Hoses to windshield washer pump
  • Wiper linkage
  • Fuses 6 (5A), 8 (5A), 15 (5A), and 20 (5A)
  • Wiring harness
  • Loose or corroded connector(s)
  • Relays
  • Motors
  • Multifunction switch
  • Washer fluid level switch


----------------------------------------
  • The wipers are inoperative — rear
  • Fuses 6 (5A), 8 (5A), 15 (5A), and 20 (5A).
  • Circuitry.
  • GEM.
  • Multifunction switch (wiper/washer switch).
  • Rear wiper up relay.
  • Rear wiper down relay.
  • Rear wiper motor.

May 12, 2009 | 1999 Ford Expedition

1 Answer

Winshield washer motor does not run


These days, most windshield washer pumps are mounted to the bottom of the washer fluid reservoir. Where’s that, you ask? Well, inner+fender+w+text.jpgyou know that spout you pour the fluid into—the one that disappears into nowhere? Well, the reservoir is actually 2384f71.jpglocated inside the front fender between the bumper and the front wheel. To replace the pump, you will have to jack up the vehicle, remove the front wheel and then remove the inner fender liner.

Jun 08, 2008 | 2001 Honda Civic

Not finding what you are looking for?
2001 Honda Civic Logo

Related Topics:

107 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

74192 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7194 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...