Question about 1995 Jeep Grand Cherokee

1 Answer

Bleeding a 2.7CRD engine

How do you bleed the fuel system on a 2.7CRD diesel engine in a Jeep Grand Cherokee?

Posted by on

  • Anonymous Mar 14, 2014

    bleeding fuel injectors

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 475 Answers

It's been awhile with diesel engines, go buy yourself a repair manual.

Posted on Oct 07, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you bleed a diesel pump jeep Cherokee turbo diesel 3.1 5 cylinder 2001


we dont have this engine here, USA.
but i have the WG jeep book,
starting page 12 , chapter 14


FUEL INJECTION PUMP BLEEDING
(1) If the fuel injection pump has been replaced,
air should be bled at the overflow valve before
attempting to start engine.
(a) Loosen the overflow valve (Fig. 18) at the
rear of the injection pump.
(b) Place a towel below the valve.
WARNING: WHEN CRANKING THE ENGINE TO
BLEED AIR FROM THE INJECTION PUMP, THE
ENGINE MAY START. PLACE THE TRANSMISSION
IN NEUTRAL OR PARK AND SET PARKING BRAKE
BEFORE ENGAGING THE STARTER MOTOR.
CAUTION: Do not engage the starter motor for
more than 30 seconds at a time. Allow 2 minutes
between cranking intervals.
(2) Crank the engine for 30 seconds at a time to
allow air trapped in the injection pump to vent out
the fuel injector drain tubes. Continue this procedure
until the engine starts. Observe the previous WARNING
and CAUTION.
(3) Tighten overflow valve.
HIGH-PRESSURE FUEL LINE BLEEDING
WARNING: THE INJECTION PUMP SUPPLIES HIGH-
-PRESSURE FUEL OF APPROXIMATELY 45,000 KPA
(6,526 PSI) TO EACH INDIVIDUAL INJECTOR
THROUGH THE HIGH-PRESSURE LINES. FUEL
UNDER THIS AMOUNT OF PRESSURE CAN PENETRATE
THE SKIN AND CAUSE PERSONAL INJURY.
WEAR SAFETY GOGGLES AND ADEQUATE PROTECTIVE
CLOTHING AND AVOID CONTACT WITH
FUEL SPRAY WHEN BLEEDING HIGH-PRESSURE
FUEL LINES.
WARNING: DO NOT BLEED AIR FROM THE FUEL
SYSTEM OF A HOT ENGINE. DO NOT ALLOW FUEL
TO SPRAY ONTO THE EXHAUST MANIFOLD WHEN
BLEEDING AIR FROM THE FUEL SYSTEM.
Bleed air from one injector at time.
(1) Loosen the high-pressure fuel line fitting at
the injector (Fig. 19).
(2) Crank the engine until all air has been bled
from the line. Do not operate the starter motor
for longer than 30 seconds. Wait 2 minutes
between cranking intervals.
(3) Start the engine and bleed one injector at a
time until the engine runs smoothly.

end quote.
pump timing is on next page
or tank filter line priming before. above.

Mar 22, 2016 | Jeep Cars & Trucks

1 Answer

2003 Jeep Cherokee Laredo started overheating after replacing thermostat.


This is s common fault after replacing thermostat, there is a system bleed screw located on radiator which will need bleeding? If you warm engine up"only warm not hot" then locate bleed screw and slacken off, not unscrew all the way? You will hear a hissing noise of the air in you system. Very similar to central heating radiator in a house! Once you have water coming through then tighten up bleed screw/bolt and give engine a bit of a run. Hope this helps

Oct 15, 2013 | 2003 Jeep Grand Cherokee

1 Answer

1997 Jeep grand Cherokee limited 5.2l v8....how to fix very stiff steering. I have changed the power steering pump already an it is still hard to turn my wheels


sound like lack of lubrication at the steering joints, your ball joints need greasing and make sure you bleed power steering system, check power steering fluid level.if low more like power steering system full of air need bleeding.

Jan 25, 2012 | 1997 Jeep Grand Cherokee

1 Answer

Petrol put into diesel car now it wont start


Drain all the petrol on your tank and so on the injection pump by pumping it. Open or loosen small tube going into the engine from the injection pump, to drain all petrol.

Make sure that petrol are remove from the engine fuel system, change fuel filter also. After removal bleed the engine.

Feb 28, 2011 | 2002 Jeep Grand Cherokee

1 Answer

95 jeep cherokee is overheating and coolant radiator fans are not


no bleeding necessary,i would recommend let it run for awhile to allow the level to adjust after the fluid
level drops when a percentage enters the engine

Jun 21, 2010 | 1995 Jeep Grand Cherokee

1 Answer

How to bleed brakes in 2004 jeep grand cherokee


Pretty much the same process always used. Begin at the passenger side rear wheel. With the engine running, have someone gently but firmly press down on the brake, open the bleed valve on the wheel cylinder or caliper (whichever you have) then close the valve and repeat the process 'till no air comes out. While doing that, keep checking the master cylinder so it does not go low on fluid or you will need to start all over again. Repeat the same process on the drivers rear, passenger front and drivers front (in that order)
I always finish by going back to the first one and re-checking it. Top off the master cylinder and you should be finished. Check all lines and fittings for leaks....your system is sealed and should never require bleeding except when it has been opened during a repair.
While bleeding, do not use excessive force pushing the pedal down...that can damage the master cylinder. Always close the valve you are bleeding before taking pressure off the pedal.
It is a good idea to remove the fluid from the master cylinder reservoir with a turkey baster etc once a year to get new uncontaminated fluid into the system. No bleeding required to do that.

May 12, 2010 | 2004 Jeep Grand Cherokee

1 Answer

Coolant is low. bleeding system?


Hi.You have to open that bleeding screw until all the air is out of the cooling system

Nov 17, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Nov. 94 Grand Cherokee Jeep no back brakes


I bet you still have air back there. If you didn't bleed the system after the master you need to do that. Bench bleeding a master doesn't always work.Also badly out of adjustment rear brakes can act the same way.

Nov 26, 2008 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Jeep Grand Cherokee Logo

Related Topics:

1,104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

63572 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...