Question about 2004 Chevrolet Blazer

1 Answer

Key stuck car ignition will not turn off or on key stuck in between vehicle has security starter which takes a remote button but will not start with it either

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Took it to thornhill automotive and paid three hundred dollars for them to reset the security system

Posted on Jul 16, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I called myself programming the new keys for my pt cruiser, but,it didnt take. At first it would start and run for a few seconds, now it wont turn over.what did I do wrong and how can I fix this?


Takes the master key to get it started again. The security gives you 3 tries to get the vehicle started, after the third time, it kills the starter.
2002 Chrysler PT Cruiser Note: You must have two valid keys to add a new key to the system.
1. Insert the first valid key into the ignition switch. Turn the ignition switch to the
ON/RUN position for at least three seconds, but no longer than 15 seconds.
Then, Turn the ignition switch to the LOCK position and remove the first key.
2. Insert the second valid key into the ignition switch. Turn the ignition switch to
the ON/RUN position within 15 seconds. After 10 seconds, a chime will sound.
In addition, the Vehicle Security Light will begin to flash. Turn the ignition switch
to the LOCK position and remove the second key.
3. Insert the new key into the ignition switch. Turn the ignition switch to the
ON/RUN position.within 60 seconds. After 10 seconds, a single chime will
sound. In addition, the Vehicle Security Light will stop flashing. To indicate that
programming is complete, the Vehicle Security Light will turn on again for
seconds and then turn off.
The new key is now programmed. The Remote Keyless Entry transmitter will
also be programmed during this procedure.
Repeat this procedure to program up to eight keys.

Oct 09, 2016 | Cars & Trucks

2 Answers

Which buttons do i push on the viper key fob to remotely start my 2002 ford f150 crew cab. the truck turns over but will not start


you push the ******(star)******* to start it .if it is not starting but starts with a key either wires have come off of remote starter or the remote starter has gone bad.

Mar 03, 2015 | Ford Cars & Trucks

1 Answer

What will keep my car from starting?


Sounds like a security problem....My bet is on the keys and the remote.. If the dealership did not program the keys correctly the car will not start...Is the security light coming on..? If you still have your old key ...see if it will start the vehicle... if it does...put the old key in and turn on the car...do not start...then withing a few second put the new car in the ignition and turn on ..wait ...then start...and the programming should complete itself. You may have one of those keys that could be removed even with the vehicle running..

Feb 24, 2015 | 2006 Chevrolet Impala

2 Answers

When I put the key in the ignition it doesn't try to start everything else comes on then shuts off. I drove it yesterday but now it won't work


The remote starter module is not getting an electrical signal when you turn the key to the on position after remote stating the vehicle. When you depress the brake without turning the key on the vehicle shuts down. The remote module thinks the key is off even when you turn it on. There is a loose connection or the remote start device is defective.

Jun 04, 2014 | 2005 Chrysler 300

1 Answer

Prostart locks and unlocks but won't start truck


Two things, Some Chev's have a security key that will only start the car when the ignition finds the ID chip in the handle of the key, when some places install remote starters they take the ID chip from the key and glue or tape it to the ignition switch so the remote starter will start the car without the key in it. I have seen some of the glue and or tape give out and the little chip falls far enough away from the ignition switch that it cannot find it and thus will not start. this is why it will work with the key in the ignition, You will have to find a service tech that knows how to remove the chip from your key handle (the plastic you turn when the key is inserted) then place it where the ignition switch can read it correctly. The ID chip is about the size of a grain of rice an is located in a small compartment in the plastic handle of the ignition key it is well hidden but a tech that has worked with this can find it. You could do the same if you get a additional key made for your car and place the key in the steering column very close to the ignition switch, but the new key can cost you in the $50 to $80 range so a tech would be a cheaper choice.
The second thing it may be is a bad isolator relay used in the remote starter, this relay is used by some more expensive remote starters to bypass the security system of the car by other means than placing the ID chip on the ignition switch. This would also need a tech to figure it out. But it should not cost more than $90 to fix by the tech, (less any cost to replace the ID chip or relay).

Nov 12, 2013 | Chevrolet Blazer Cars & Trucks

2 Answers

2003 Chevy Impala 78,000 miles KEY WILL NOT TURN. - Car was running fine! - Turned off key. - Tried to restart and Key will Not Turn. It was jammed in the OFF position. - I removed ignition...


ur still in a security lock out with ignition[ key ] system u might have to have it towed to dealer for them to hook up vehicle[contact dealer and advise what is happening and also recheck new key] for reprograming or reset system..some vehicles if u try to start vehicle while in a security mode can get completely locked out of vehicle and if u replaced the whole ignition housing and not just the cylinder the housing is the reader the wiring that is around the housing cylinder tube is what reads the key and syncs with the vehicle if u put in a different one or the wiring is damaged vehicle wont start and will stay in security mode

Jul 02, 2011 | 2003 Chevrolet Impala

3 Answers

I start my car but it immediatly shuts off and the theft sys light flashes could this light be the reason?


the ignition swith reads the key chip when key is turned, this is a common problem,the ignition switch will need to be replaced, after replacing the swith reprograming will be needed, to program you will need a battery charger to keep battery from going dead, after installing new switch,turn charger on, turn key to crank then release key leaving ignition on, you will see the dash lights, leave key on for about 15-20 min, until you see theft light go out, if light doesnt go out then repeat process,crank for 2 sec, then leave key on 15-20 mins until security/theft light goes out, hope this helps.

May 09, 2010 | 1997 Pontiac Grand Am

2 Answers

2003 chevy tahoe with key stuck in ignition. vehicle previously broken into and stolen with scewdriver to ignition. ignition replaced. key now stuck and cannot turn vehcile off. can shift to driver,...


I have towed several of these with same problem. Sounds like to me it needs to go back in for the ignition switch again. Unless it's not going into park. If it's not going into park it would be a shift linkage issue and needs to be adjusted. Chris J.C. Towing & Recovery

Apr 09, 2010 | 2002 Chevrolet Tahoe

1 Answer

2003 Montana Remote & Key Programming Help ..


Ignition keys relearn takes about 30 min to do. 30-Minute Learn Procedure 1. Turn ON the ignition, with the engine OFF. 2. Attempt to start the engine, then release the key to ON; the vehicle will not start. 3. Observe the SECURITY tell tale light. After approximately 10 minutes, the light will turn OFF. 4. Turn OFF the ignition switch, and wait 5 seconds. 5. Repeat steps 1 through 4 - two more times - for a total of 3 cycles of 10 minutes. 3x10 = 30 minutes. The vehicle is now ready to relearn the Passlock Sensor Data Code and/or passwords on the next ignition switch turn from OFF to CRANK Important: Turn the Ignition Switch OFF. The vehicle learns the Passlock Sensor Data Code and/or password on the next ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle. 6. Start the engine. The vehicle has now learned the Passlock Sensor Data Code and/or password. 7. With a scan tool, clear any DTCs if needed. History DTCs will self clear after 100 ignition cycles. Without a scan tool you may have momentary starter interruptions while history clears itself.

Oct 29, 2009 | 2003 Pontiac Montana

3 Answers

Key Does Not Work


It could be that chip inside key just went bad. Do u have a 3rd key? That works? If so take the 2 good keys and turn the igntion to run postion for 3 secs each then do the same for the 3rd key and this will reprogram it if the chip is ok. If you do not have 2 good keys then u will have to have a scan tool that will link up with PATS system and perform security access to reprogram it.

Feb 12, 2009 | 2005 Ford Taurus

Not finding what you are looking for?
2004 Chevrolet Blazer Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...