Question about 1992 Ford Explorer

2 Answers

Egr valve where is the egr valve on a 1992 ford explorer 4.0liter

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It uses an air injection system NOT a typical EGR valve to reduce Hydro-carbons.

Posted on Aug 02, 2008

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 148 Answers

It should be on the intake manifold ,towards the very back,it will have a thin rubber hos attatched to it

Posted on Jul 13, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Why is codes p2106 p0401 on?


P2106 THROTTLE ACTUATOR CONTROL SYSTEM,-PO401-EGR INSUFFICIENT FLOW

May 29, 2014 | 2005 Ford Explorer

1 Answer

I have a po401 code on my 96 Ford explorer


Your egr port is probably block..Apply vacuum to your EGR valve,while the vehicle is running..The vacuum should hold and the vehicle should run very rough or even go dead..If the valve doesnt hold vacuum,,then replace the valve..If the valve holds vacuum,but there is no difference or very little difference,,the EGR port is clogged in your intake..If all works fine ,,then suspect the DPFE sensor..This tells the computer if your receiving any flow..from the EGR

May 06, 2012 | 1996 Ford Explorer

1 Answer

Where is the egr valve on the 2006 ford explorer


i hope that this could help you the EGR valve is the item #7

ganyapr_0.jpg

Item Part Number Description 1 - EGR system module electrical connector (part of 12B637) 2 9E498 Engine vacuum harness 3 - EGR system module-to-exhaust manifold tube upper fitting (part of 9E469) 4 - EGR system module-to-exhaust manifold tube lower fitting (part of 9E469) 5 9E469 EGR system module-to-exhaust manifold tube 6 W506024 EGR system module bolts (2 required) 7 9D475 EGR system module 8 9D476 EGR system module gasket

Feb 13, 2011 | 2006 Ford Explorer

1 Answer

Ford Explorer : How to Troubleshoot the EGR P0401 Trouble Code


P0401 - Exhaust Gas Recirculation Flow Insufficient Detected

Possible Causes:
- Harness or connectors (EGR volume control valve circuit is open or shorted.)
- EGR volume control valve stuck closed
- EGR volume control solenoid valve
- Dead (Weak) battery
- EGR passage clogged
- Exhaust gas leaks
- Faulty EGR valve

Possible Solutions:
- Clean EGR Valve
- Replace EGR Valve
- Repair EGR harness or connector
- Replace EGR volume control solenoid valve
- Replace EGR volume control valve

Jan 24, 2011 | Ford Explorer Cars & Trucks

1 Answer

I need a list of all emission control devices on a 96 ford explorer for a paper im writing for my apprenticeship


1996 Ford Explorer 2WD 5.0L


Canister Purge Valve
Catalytic Converter

EGR Position Sensor

EGR Vacuum Solenoid

EGR Valve

EGR Valve Gasket

EGR Valve Pressure Sensor

Exhaust Manifold

Exhaust Manifold Gasket

Fuel Cap

Muffler - Performance

Oxygen Sensor

PCV Valve

Sensor - Ambient Air Temperature

Smog Pump

Jan 15, 2011 | 1996 Ford Explorer

2 Answers

Replaced egr valve pressure sensor upstream and downstream oxygens sensors egr tube new egr valve new idle air control valve runs fine and idles fine one minute then starts idleing rough and dies starts...


r u gonna keep replacin parts-or do a scan 1st--not all problems show on a readout-like vacuum leaks or a failin computer--throttle body probly needs cleanin

Sep 06, 2010 | 1996 Ford Explorer

1 Answer

Where is the camshaft sensor located on a 1996 ford explorer 4.0 literand where is the egr valve located also


cam sensor is located rt side of engine half way up egr is left side of engine front ove valve cover

Mar 03, 2010 | 1996 Ford Explorer

1 Answer

I put a 1992 Ford Explorer motor in a 1994


they come off the exhaust manifold...

Jul 16, 2009 | 1992 Ford Explorer

1 Answer

1992 ford ranger 2.3 liter engine


on code 328 Replace the EGR valve. and code 332 Replace the EGR valve man !

Aug 09, 2008 | 1992 Ford Ranger

1 Answer

2002 Ford Explorer 4.0L V-6


do you have a code for egr? if you do follow the hose all the way to the egr solenoid and meke sure the othe hose atached to the solenoid has vacium, the egr only gets vacium when the computer triger it but not all tyhe time

May 26, 2008 | 2002 Ford Explorer

Not finding what you are looking for?
1992 Ford Explorer Logo

Related Topics:

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60541 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21927 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...