Question about 2007 Nissan Altima 3.5 Sedan

1 Answer

Driver's Seat Removal

I dropped a flash drive under the driver's chair in my '07 Altima-2.5 s, and can't see it or reach it. How do I take off the front cover of the seat, or the seat itself?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Nissan Expert
  • 99 Answers

There are four bolts holding the seat to the floor. Slide the seat all the way forward and you will be able to see the two bolts which are at the rear of the seat slide rail. They are 14mm bolts, remove them. Slide the seat all the way back and remove the two bolts at the front of the rail. Once the bolts are out removed tilt the seat towards the back, it should lift the seat bottom easily and you can find your flash drive. Be careful not to push the seat too far back as there may be a wiring harness to damage. Once you retrieve the flash drive, put the seat back down and put the bolts back in.

Posted on Nov 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Power seat disconnect/removal - driver's side


there are 4 star bolts that keep the seat in place usually under each corner coverd by a plastic sliding plate remove the plates then the bolts * 4 there will be a harness under the seat disconect this and also the seat belt seat will come out its a 10 minuet job

Jan 25, 2014 | 2001 Mercedes-Benz C-Class

1 Answer

My tail lights and dash lights keep flcking n and off in my 2007 pontiac g5


shorted wiring , usually found under carpet area towards rear passenger area. removal of rear seat required (battery under seat) I have found breaks usually around driver seat mounting ( driver seat removal may also be required to find break/short)

Jan 21, 2014 | Cars & Trucks

1 Answer

Removal of passenger seat on a 2006 ford fusion


there are four bolts.. 2 can be reached in the back seat and 2 up front just below the seat. remove four bolts and the seat should come right out. the bolts might be hidden under a plastic cover

Jul 18, 2012 | 2006 Ford Fusion

1 Answer

How do iremove front seat from a 1997 honda accord


1. Make sure you have the anti-theft codes for the radio and the navigation system, then write
down the frequencies for the preset buttons.
2. Tilt the steering wheel all the way up and telescope it all the way in.
3. '04-07 models passenger's seat: Carefully insert the tip of a small screwdriver (A) through
the hole in the back of the front seat belt lower anchor cover (B) and into the hole in the
front seat belt lower anchor (C). Unlock the lower anchor by pushing in on the screwdriver.
Remove the screwdriver, and then detach the front seat belt anchor plate (D) and anchor
cover from the lower anchor.4. Slide the seat all the way forward, then remove the seat track end covers from the back of both seat tracks.5. Slide the seat about half way to the rear so you can access the seat mounting bolts. If equipped with the driver's 8-way power seat, fully raise the seat.
6. If equipped with a side airbag, disconnect the negative cable from the battery, and wait at
least 3 minutes before removing the seat. 7. Remove the bolts securing the front seat. 8. Lift up the front seat, then detach the harness clip and disconnect the connector.
If equipped, the seat heater connector on the 2-way power seat and passenger's
manual seat. '04-07 models, disconnect the seat position sensor subharness connector on the
driver's manual height adjustable seat and the driver's 8-way power seat.
9. With the help of an assistant, carefully remove the front seat through the front door opening. 10. Install the seat in the reverse order of removal, and note these items:
Apply medium strength type liquid thread lock to the front seat mounting bolts
before reinstallation.
Make sure each connector is plugged in properly.
Tighten the seat mounting bolts to the specified torque in the sequence shown.
Slide the seat all the way back and tighten then slide it forward and
tighten Before attaching the lower anchor bolts, make sure there are no twists or kinks in
the seat belts. 04-07 models passenger's seat: The triangle marks on the anchor plate and
the lower anchor must face the same side. Insert the anchor plate into the lower
anchor, and make sure that it is locked securely. If equipped with a side airbag, reconnect the negative cable to the battery. Enter the anti-theft codes for the radio and navigation system, then enter the radio station presets. Reset the clock. Your all done. Drink a cold beverage and enjoy the rest of your weekend! hope this helps. Dave

Jun 16, 2011 | 1997 Honda Accord

1 Answer

How do i make my nissan altima adaptable for a disabled driver?


This is a science, and improper methods VOID INSURANCE coverage. A qualified modifier needs to do this job. Each and every one is specialized to suit, based on the needs. This all has to be approved, down to the seat belt stuff (different for motorized wheel chairs, for example). The do make some really cool mods these days, but with disabled, often it needs to be a van. Hard to do much in a car...

Aug 19, 2010 | 2008 Nissan Altima

2 Answers

I need to remove driver side seat on 2009 Maxima my wife dropped a diamond from her ring and need to get access to get it out from under the seat


should be 4 bolts holding seat into floor pan, one under each corner of the seat. Remove bolts, unplug any power connections , seat should come right out.

Aug 01, 2010 | 2008 Nissan Maxima

1 Answer

Flashing light on dash - seatbelt indicator


you did'nt state year, make, model. If you are talking about the seat belt light, check your seat belt(the one with the push/release button. check this top to bottom for a broken wire. ckeck under the seat the harness may be damaged as well. If it is the air-bag light bring it to your mechanic. air-bag circuits should be touched without the right knowledge and tools.

Apr 20, 2009 | 2003 Nissan Altima

1 Answer

Nissan Primera SE plus 2000 (W) Petrol I have removed my driver seat to wash carpet under driver seat, when I put seat back on Airbags light turn on don't know how to switch it off


Please just take the car for a scan and all issues will be rectified there for you.

You dont have a problem.

Adice you to service your air-bags every 2 years.

Apr 10, 2009 | 2000 Nissan Altima

1 Answer

Driver seat removal


there are four bolts (2 in ft ,2 in rear)that bolt seat to floor. you will need slide seat all the way forward to access rear bolts, they may ,if they are still there, be under plastic beauty caps. do the same for ft bolts. once loose tillt seat assy backwards and unplug any wiring connectors on bottom f seat

Oct 26, 2008 | 1988 Acura Legend

Not finding what you are looking for?
2007 Nissan Altima 3.5 Sedan Logo

383 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...