Question about 2000 Ford Expedition

2 Answers

Where is the oil sending unit on a 2000 5.4 litre expedition

I just need to know where to look for the oil sending unit. The oil pressure gauge moves upt to normal pressure the bottoms out and the idiot lights come on. Within a mile to a mile and a half it does this several times, then it goes to the normal range and stays there. I already have the switch, just need to know where it is on the block.

Thanks
Terry

Posted by on

  • Anonymous Mar 23, 2014

    oil pressure sending unit ok or oil pump the problem

  • Anonymous Mar 25, 2014

    oil sending unit light stays on

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

It is right by ur oil filter.....on thr oil filter housing

Posted on May 17, 2013

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Ford Master
  • 61,037 Answers

The pressure sender is near/next to the oil filter. And yes this does sound like a sender issue.

Posted on Jul 28, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the oil pressure sending unit located in a '01 dodge dakota, 4.7 eng.?


go to CTC and buy a service manual for 2001 dodge Dakota 4.7 litre engine there will be 2 oil pressure sending units one that is for the gauges in the dash and the other for the oil pressure sending unit mounted on engine

Feb 12, 2015 | Dodge Cars & Trucks

2 Answers

I;ve lost oil pressure the needle stay's down while driving, is the oil pump bad or going bad? is it located in the oil pan or the front of the 4.6L MOTOR?


If the needle is staying down and the motor is not knocking then the gauge is probably bad. If you run the engine with no oil pressure, then it will not last long. It will start knocking and ruin the engine. But yes the oil pump in in the oil pan. There is also a oil pressure sending unit that could be bad. It is located on the back of the engine.

Jan 03, 2011 | 2000 Ford Expedition

1 Answer

Where is the oil pressure switch/sendor located?


Oil pressure can be checked at the sending unit passage with an externally mounted mechanical oil pressure gauge. To get accurate results from the test, make sure you follow the manufacturer's recommendations and compare your findings to specifications.
Testing the Oil Pressure Gauge
  • Test the gauge by grounding the wire that leads to the sending unit on the block.
  • When the wire is disconnected from the sending unit with the key switch on, the needle on the oil pressure gauge should be either all the way high or all the way low. Grounding the wire should make the needle move to the opposite side of the gauge from where it was before the wire was grounded. If the vehicle is equipped with an oil pressure light, touching the wire to ground and then removing the wire from ground should turn the light on and off.
  • If either happens, the gauge and wiring are good and the sending unit is at fault.
Testing Oil Pressure
Pressure can be tested by temporarily installing an oil pressure gauge in place of the sending unit. Before testing, look up the oil pressure specifications for your vehicle in the appropriate service manual.
  • Bring the engine up to operating temperature.
  • Now shut the engine off.
  • Locate the oil pressure sending unit; usually it is on the lower side of the engine block.
  • Disconnect the wire from the sending unit and use an open ended wrench to remove the sender. Using pliers can damage the unit.
f43-19.jpg An oil pressure sending unit is removed with a special socket. Courtesy of Chrysler Corporation.
  • Tighten the oil pressure test gauge into the hole in the block where the sender was removed.
f11-15_3184.gif Measuring oil pressure. Reprinted with permission.
  • Check the engine's oil level and fill, if required.
WARNING Be extremely careful when working near a running engine. Always wear safety goggles or glasses with side shields when working around moving machinery and be sure that your clothing is not loose.
  • Now turn the engine on and check the oil pressure on the gauge.
    • Watch as the engine warms to note any excessive drops due to temperature.
    • Make sure the engine speed is set to specifications for testing pressure.
    • If necessary, us a tachometer and adjust the engine idle speed.
  • Record the measured oil pressure, then turn off the engine.
  • Compare the test results with the manufacturer's specifications.
    • If the oil pressure is within specifications, this shows that the oil pressure sending unit may not be working correctly.
    • In many cases, replacing the oil sending unit will correct the problem.
  • After the test is complete, reinstall the oil pressure sending unit, start the engine, and confirm there are no leaks.

Nov 20, 2010 | 2002 Pontiac Bonneville

3 Answers

Oil pressure light comes on.. what do i do?


Could be a few things but you should start off by checking the level of your oil. Make sure it is in the safe area

Nov 16, 2010 | 2001 Volkswagen Golf

2 Answers

Oil pressure loss


the 1st thing u do is have the oil pressure tested with a test mechanical gauge by a shop, most times it is just the oil pressure sending unit is defective, but never assume that is the problem, low oil pressure will distroy a $5000.00 engine very quickly, u can just try a new sending unit, but highly recommend a pressure test with a mechanical gauge before you run the engine anymore.

Dec 05, 2009 | 2000 Jeep Cherokee

1 Answer

Oil light blinks on and off could pressure switch be bad if so where is it located on a 2000 ford windstar 3.0


Oil Pressure Switch Operation:
00134_oil_pressure_switch_gauge.jpgInformation relay unit for the indicator light or gauge on instrument panel. It contains a diaphragm that responds to changes in oil pressure. When the oil level is over a pre-set limit, the diaphragm opens the switch, turning off the light. When level is below the pre-set limit, the dash light comes on. In later model cars, if the oil pressure drops, the switch turns off the fuel pump, to stop the engine and limit damage to internal parts. Oil pressure switches can be grouped into two categories, units for electrical gauges and for mechanical gauges.

Oil pressure can be checked at the sending unit passage with an externally mounted mechanical oil pressure gauge. To get accurate results from the test, make sure you follow the manufacturer's recommendations and compare your findings to specifications.
Testing the Oil Pressure Gauge
  • Test the gauge by grounding the wire that leads to the sending unit on the block.
  • When the wire is disconnected from the sending unit with the key switch on, the needle on the oil pressure gauge should be either all the way high or all the way low. Grounding the wire should make the needle move to the opposite side of the gauge from where it was before the wire was grounded. If the vehicle is equipped with an oil pressure light, touching the wire to ground and then removing the wire from ground should turn the light on and off.
  • If either happens, the gauge and wiring are good and the sending unit is at fault.
Testing Oil Pressure
Pressure can be tested by temporarily installing an oil pressure gauge in place of the sending unit. Before testing, look up the oil pressure specifications for your vehicle in the appropriate service manual.
  • Bring the engine up to operating temperature.
  • Now shut the engine off.
  • Locate the oil pressure sending unit; usually it is on the lower side of the engine block.
  • Disconnect the wire from the sending unit and use an open ended wrench to remove the sender. Using pliers can damage the unit.
f43-19.jpg An oil pressure sending unit is removed with a special socket. Courtesy of Chrysler Corporation.
  • Tighten the oil pressure test gauge into the hole in the block where the sender was removed.
f11-15_3184.gif Measuring oil pressure. Reprinted with permission.
  • Check the engine's oil level and fill, if required.
WARNING Be extremely careful when working near a running engine. Always wear safety goggles or glasses with side shields when working around moving machinery and be sure that your clothing is not loose.
  • Now turn the engine on and check the oil pressure on the gauge.
    • Watch as the engine warms to note any excessive drops due to temperature.
    • Make sure the engine speed is set to specifications for testing pressure.
    • If necessary, us a tachometer and adjust the engine idle speed.
  • Record the measured oil pressure, then turn off the engine.
  • Compare the test results with the manufacturer's specifications.
    • If the oil pressure is within specifications, this shows that the oil pressure sending unit may not be working correctly.
    • In many cases, replacing the oil sending unit will correct the problem.
  • After the test is complete, reinstall the oil pressure sending unit, start the engine, and confirm there are no leaks.




Nov 17, 2009 | 2000 Ford Windstar

Not finding what you are looking for?
2000 Ford Expedition Logo

Related Topics:

487 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...