Question about 1994 Mercury Tracer

1 Answer

Door Panels How do you take the window crank off? I need to take off the door panel and I have no idea how. The only spot holding it on is the window crank now

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

There's a small wire clip right behind where the door panel meets with the crank. Its really hard to see. I had to pry the crank a bit with a screw driver to see it. Anyway, when you do see it there's a part that protrudes more than the rest, and you can slide a screw driver back there and pry it out.

Posted on Jul 15, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove citroen c3 rear door panel


Check out how the door panels are attached to the car. Most panels use screws and bolts but others have snap-in fittings. Gather all the tools you need for removing the door panels. If the panel is attached with screws and bolts, you need a screwdriver or ratchet and socket. Car door panels with snap-in fittings are easily removed with a flathead screwdriver.
Locate where the screws and bolts are before starting. These are usually found in the arm rest area, along the bottom or sometimes near the door lights.
Roll down the car door window. Begin removing all screws and bolts that hold the door panel onto the car. If your car has snap-in fittings, pry gently on the bottom corner of the door panel until the fittings pop out.
Remove the power window control panel if your car has power windows. The control panel should pry out easily, and then you unplug the wiring harness from the back and place it to the side.
Use an L pick and flashlight when locating a manual window crank. Look behind the window crank and slide the pick under the edge of the metal clip that holds the crank in place. Remove the clip and pull the crank off.
Remove the door handle by unscrewing the small screw located in the center. Gently pull the door handle out until you see the back of the handle and unclip the rod from the door handle. This should remove the handle unless the handle and door lock are attached, then you just unclip the rod from the lock and remove them both together.
Unscrew the cap off rear upper corner door panel locks. These don't have a rod attaching them to the handle and unscrew separately from the door handle.
Pop the door panel off after you've removed everything. Gently pry on the bottom edge of the door panel until it releases. Pull out and up to completely remove the door panel.
GM Tech2 GM Diagnostic Scanner with 32MB Card and TIS2000

Oct 10, 2014 | 2006 Citroen C3 1.4i

3 Answers

2000 neon manual windows don't roll down, crank turns but window doesn't move


you need a window regulator you need to take the door apart to be sure

Jan 25, 2012 | Dodge Cars & Trucks

1 Answer

How do you remove passenger sliding door handle on oldsmobile silhouitte


The process of removing car door panels is essentially the same for each make of car. You may need to remove these panels when your fixing locks or power windows, replacing window cranks, installing speakers or replacing the side mirrors. Learning how to remove the panels yourself can save money on simple car repairs.
Related Searches:

Difficulty: Moderately EasyInstructionsThings You'll Need
  • Set of screwdrivers
  • L pick
  • Small flashlight
  • Ratchet and socket
    • 1

      Check out how the door panels are attached to the car. Most panels use screws and bolts but others have snap-in fittings. Gather all the tools you need for removing the door panels. If the panel is attached with screws and bolts, you need a screwdriver or ratchet and socket. Car door panels with snap-in fittings are easily removed with a flathead screwdriver.

    • 2

      Locate where the screws and bolts are before starting. These are usually found in the arm rest area, along the bottom or sometimes near the door lights.

    • 3

      Roll down the car door window. Begin removing all screws and bolts that hold the door panel onto the car. If your car has snap-in fittings, pry gently on the bottom corner of the door panel until the fittings pop out.

    • 4

      Remove the power window control panel if your car has power windows. The control panel should pry out easily, and then you unplug the wiring harness from the back and place it to the side.

    • 5

      Use an L pick and flashlight when locating a manual window crank. Look behind the window crank and slide the pick under the edge of the metal clip that holds the crank in place. Remove the clip and pull the crank off.

    • 6

      Remove the door handle by unscrewing the small screw located in the center. Gently pull the door handle out until you see the back of the handle and unclip the rod from the door handle. This should remove the handle unless the handle and door lock are attached, then you just unclip the rod from the lock and remove them both together.

    • 7

      Unscrew the cap off rear upper corner door panel locks. These don't have a rod attaching them to the handle and unscrew separately from the door handle.

    • 8

      Pop the door panel off after you've removed everything. Gently pry on the bottom edge of the door panel until it releases. Pull out and up to completely remove the door panel.

Jan 10, 2012 | 1998 Oldsmobile Silhouette

2 Answers

Windows willnot go up. Or down please help it is rainning


I am assuming they are power windows, take off the door panels and physically wire the door motor by hooking up a wire from the battery to the hot side of the motor. Then, hookup a ground wire to the negative side of the motor, you can connect or hold it anywhere there is a good ground, if the motor works then check the switch. If the switch isn't working, which I assuming it doesn't then replace with a new one. Happy Motoring! :)

Oct 27, 2010 | Ford Club Cars & Trucks

1 Answer

How do i remove the front door panels without damaging them?


There's a few tools you'll need:
panel removal tool $7-$10 (forked)
hand crank windows you'll also need a window crank removal tool
screw drivers - philips and small straight
Note pad and pen or pencil
zip lock plastic bag
May need:
socket set
allen and torx drivers

Use the note pad to make notes where everything goes.
Open the door all the way.
Use the straight screw driver to pop any small plastic covers off.
remove any screws that are holding the panel or arm rests or anything else attached to the door (this is where the socket, allen or torx drivers may come in handy)
put all the small part in the plastic bag.
starting at the bottom back corner start gently pulling the panel, you'll soon find spots where it's sticking, here you'll find plastic panel attachment pins. Using your panel removal tool, slide it under the panel and find the panel pins, slide the tool around the pins and pry them loose, You may find an extra screw you missed or a few panel pin toward the center, remove as before.
The panel should now be hanging by where it clips over the window edge (if working indoors, putting the window down ahead of time helps here) gentle lift and pull the panel up and off where it's hanging.
All that's left is disconnecting any wires, there will be clips molded into the sides to hold them in place, gently lift the clip and disconnect them.
Your panel should be loose.
Reverse to reinstall.


Jun 13, 2010 | 2008 Pontiac Grand Prix

1 Answer

The front passenger door window has fallen down. How do I take off the interior door panel?


after removing all visible screws on the door panel, the window crank(if equipped) and likely the door handle; the panels just snap/pop off and on.

Dec 28, 2009 | 2001 Nissan Quest

2 Answers

Remove door panel on a Ford Van


For a 1999 Ford Econoline 150 (assume the same or very similar), remove triangular plastic cover over mirror assembly by prying straight out, remove plastic door handle cover by prying up from the front side, remove electronic door switches by prying up from back side, remove round plastic cover at bottom rear of door panel. Four screws are now revealed, remove them. Lift door panel straight up, clips are hooks (not snap in). Work door switch assembly out of door panel. Set door panel aside. Reassemble in reverse order.

May 09, 2009 | 2000 Ford Econoline

1 Answer

How to remove door panel for driver and passenger side doors


Hi. This Guide will help you with this issue.



Step1 Check out how the door panels are attached to the car. Most panels use screws and bolts but others have snap-in fittings. Gather all the tools you need for removing the door panels. If the panel is attached with screws and bolts, you need a screwdriver or ratchet and socket. Car door panels with snap-in fittings are easily removed with a flathead screwdriver. Step2 Locate where the screws and bolts are before starting. These are usually found in the arm rest area, along the bottom or sometimes near the door lights. Step3 Roll down the car door window. Begin removing all screws and bolts that hold the door panel onto the car. If your car has snap-in fittings, pry gently on the bottom corner of the door panel until the fittings pop out. Step4 Remove the power window control panel if your car has power windows. The control panel should pry out easily, and then you unplug the wiring harness from the back and place it to the side. Step5 Use an L pick and flashlight when locating a manual window crank. Look behind the window crank and slide the pick under the edge of the metal clip that holds the crank in place. Remove the clip and pull the crank off. Step6 Remove the door handle by unscrewing the small screw located in the center. Gently pull the door handle out until you see the back of the handle and unclip the rod from the door handle. This should remove the handle unless the handle and door lockmag-glass_10x10.gif are attached, then you just unclip the rod from the lock and remove them both together. Step7 Unscrew the cap off rear upper corner door panel locks. These don't have a rod attaching them to the handle and unscrew separately from the door handle. Step8 Pop the door panel off after you've removed everything. Gently pry on the bottom edge of the door panel until it releases. Pull out and up to completely remove the door panel.


Please rate and have a great day:)

Mar 25, 2009 | 2002 Kia Optima

1 Answer

How do I remove the door panels to change the speakers in the front doors of a 1999 Ford Escort?


remove the front door pull cup screw
remove the screw cap and screw from inside handle and slide the handle rearward to disengage the hook from the inner sheet metal. disconnect inside handle from latch remote link if manual windows- remove crank with store bought remover tool. Remove the 2 pushpins from the door trim panel using trim tool pry away door panel [7] fasteners holding panel and push panel in and up . if elect windows disconnect switches

Feb 17, 2009 | 1998 Ford Escort

1 Answer

97 VW Jetta right rear power window off track


There should be six or seven allen wrench screws around the edge of the door panels. Loosening these releases the retaining clips inside. You will then want to remove the manual window crank if you have one by laying two fingers flat on the door panel and pushing the ring around the base of the crank sideways. You might have to rotate around this as it only pushes one way. Next you will have to remove the two large golden screws directly under the door panels handle. If you have rear door panel speakers you will have to politely pry off the speaker grill with a flat blade screwdriver and remove the speakers four screws and the wire clip from behind the speaker. You will also have to unscrew the door lock post. Then you should be able to lift the door panel up to release the top lip of it from the door.

Dec 29, 2008 | 1997 Volkswagen Jetta

Not finding what you are looking for?
1994 Mercury Tracer Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Fordexpert

Level 3 Expert

5331 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...