Question about 2000 GMC New Sierra 1500

1 Answer

Replace rear axel bearing on 4x4 5.3 Litre gas engine

2000 GMC Sierra 1500

Posted by on

  • shhhh_55 Jul 21, 2008

    Thank you!

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 131 Answers

Loosen differential cover and let oil drain. Remove cover, remove U lock from axel. Pull axel out. Remove bearing seal then bearing. Install new bearing, seal and reinstall axel. Reinstall U lock and new cover gasket. Fill with 75-90wt gear oil. Now I know that sound pretty straight forward. But there are some things to remember. The U lock can be difficult to remove sometimes. The most important thing is the seal, you will need to make sure it gets seated correctly and not torn when installing axel.

Posted on Jul 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I remove the rear axles on a 2002 GMC Serria 1500


remove the back cover small bolt take it out '8 millimeter /on the crown and push the pin out push in on the axel key on the axel will fall of then pull it out

Sep 23, 2014 | 2002 GMC Sierra 1500

1 Answer

I need to remove the rear axels of a 2000 GMC Sierra


Ok, here is your worklist for the 2000 Sierra assuming the auto transmission
3_21_2012_1_33_56_am.jpg

Mar 21, 2012 | 2000 GMC Sierra

2 Answers

I have a 97 gmc sierra 1500 4x4, it runs very nice the only thing is when i reach 40 mph, there is a slight vibration or shake. it seems to only happen between 40-45 mph, it runs perfect before 40mph and...


There are several things to consider, first I would check the tire balance. Then I would go to the front alignment. If you have trouble on one side or the other you may just have a bad tire.

Apr 01, 2011 | 1997 GMC Sierra

1 Answer

Rear-end grinding noise in 1993 GMC Sierra 1500


your description sounds like the gears inside the the same differential you just replaced.

Oct 13, 2009 | 1993 GMC Sierra K1500

2 Answers

Front end bearings need to be replaced


Yes New bearing should do the trick

Sep 26, 2009 | 2000 GMC New Sierra 1500

2 Answers

Need to replace brake line from rear axle forward on a 1996 gmc sierra 1500 pu xcab. i need a diagram.


Chanses are it broke behind the gas tank wear it runs along the frame rail. You don't need a diagram to fix that, just unhook it at both ends and break it off or cut it off buy the tank and take the pieces with you to a auto parts store and they will match it up with new line, just take a tape measure and measure from the rear axel to the front block or perportioning valve, and don't worry about the piece behind the tank, just run the new line alongside the old one behind the tank unless you want to pull the tank out.

Sep 06, 2009 | GMC Sierra 1500 Cars & Trucks

1 Answer

2001 gmc sierra 1500 2 wheel drive shakes when taking off from stop shakins stops at about 15 mph was told drive shaft angles to side then back to diff. is this normal mechanic said he was not sure if this...


on a two wheel drive the shaft should only angle down if this a used truck I would say the rear
axel was hit on the side that the drive shaft angels away from and the alignment should be checked out.

Mar 06, 2009 | 2001 GMC Sierra C/K3500

1 Answer

Debree shields behind rear disc brake rotor rotted out.


Not hard to Replace. you will have to take the Caliper off of the Rotor and then Take the Rotor off, Repack the Bearings! And it is Right There!

Jan 18, 2009 | 2000 GMC New Sierra 1500

1 Answer

2005 GMC Sierra 1500 rear noise


you need to check you universal joints usualy the one on the rear axel is the first to go. i recomend to put bolth in at the same time. the new ones will be greasable so dont forget to give them a little every oil change

Aug 23, 2008 | 2005 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

481 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...