Question about 1992 Cadillac Seville

1 Answer

1992 A/C Blower Motor Replacement

Any short cuts when removing A/C Blower Motor?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Nope but you have to slice side of black plastic to remove it

Posted on Dec 01, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The heater blower stopped working and the fuse is not blown?


Blower Motor Removal & Installation W/O Air Conditioning Blower Motor (W/O Air Conditioning) gm-10-00-634.gif

To Remove:
  1. Remove the PCM.
  2. Remove the coolant reservoir.
  3. Remove the rear coolant recovery reservoir mounting stud.
  4. Disconnect the cooling tube from the blower motor.
  5. Disconnect the electrical connector from the blower motor.
  6. Remove the blower motor mounting bolts.
  7. Remove the blower motor insulating cover.
  8. Remove the blower motor.
To Install:
  1. Install the blower motor.
  2. Install the blower motor mounting bolts.
  3. Connect the electrical connector to the blower motor.
  4. Connect the cooling tube to the blower motor.
  5. Install the rear coolant recovery reservoir mounting stud.
  6. Install the coolant reservoir.
  7. Install the PCM.
W/ Air Conditioning Blower Motor (W/ Air Conditioning) gm-10-00-633.gif

To Remove:
  1. Remove the PCM.
  2. Remove the coolant reservoir.
  3. Remove the rear coolant recovery reservoir mounting stud.
  4. Disconnect the electrical connector from the blower motor.
  5. Move the PCM connectors out of the way.
  6. Remove the blower motor access cover screws. CAUTION
    Do not cut any deeper than necessary in order to remove the access cover.
  7. Cut through the access cover on the cut line using a sharp utility knife.
  8. Disconnect the cooling tube from the blower motor.
  9. Remove the blower motor mounting bolts.
  10. Remove the blower motor.
To Install:
  1. Install the blower motor.
  2. Install the blower motor mounting bolts.
  3. Connect the cooling tube to the blower motor.
  4. Install the blower motor access cover.
  5. Install the blower motor access cover retaining screws.
  6. Using black weather-strip adhesive, seal the cut line.
  7. Connect the blower motor electrical connector.
  8. Reposition the PCM connectors.
  9. Install the rear coolant recovery reservoir mounting stud.
  10. Install the coolant reservoir.
  11. Install the PCM.
prev.gif next.gif

Feb 08, 2011 | 1996 Chevrolet Blazer

Tip

Replacing a blower motor in a 04-08 Suzuki Forenza


After experiencing the cold this winter because of my blower motor giving out i thought i would share how to replace it.
mine went out gradually, worked a few day then stopped and progressively got worse.

you will need a mid sized, short star (Phillips) head screw driver (especially for the back), needle nose pliers, utility knife, patience

you will find the blower motor under the passenger side dash to the right, unless you are flexible feel for a round 5 inch cylinder, you can use a large mirror with a stand, you will need to pull the carpet down, to the left of the cylinder you will find a rectangle "seat" this where the blower locks into place, to the right is the connection cable, evenly around the cylinder are your 5 hex head screws, they are brass in color so not hard to spot, (you can use a ratchet drive for the front 3) loosen and remove each screw, along the fire wall under the blower motor is rubber insulation, you will see a 6 inch bump, using your utility knife cut along the top and notch down both sides of the first cut, this will help with removal and replacement of the motor, pull down on the blower motor and slid it out, this may take a little careful wiggling, once out use your pliers to squeeze the side and pull the connecting cable from the socket, the connection are angled like ' - so this no way to mess up reconnecting the replacement motor, I bought mine from the wreaking yard for $32 (had them pull it for $10 included in the price) new costs $75 and $160, your choice, the wreaking yard bench tested it for me so i know it works but here you can check for your self if in fact the blower motor is the problem.
connect the cable to the replacement motor, turn on your ignition and turn on your fan, if your fan spins you are good to go.
replacing the blower motor is a reverse of the above.

Have fun

on Feb 10, 2015 | Suzuki Cars & Trucks

1 Answer

How to change blowermotor on 2001 gmc jimmy


Blower Motor Removal & Installation W/O Air Conditioning Blower Motor (W/O Air Conditioning) gm-10-00-634.gif

To Remove:
  1. Remove the PCM.
  2. Remove the coolant reservoir.
  3. Remove the rear coolant recovery reservoir mounting stud.
  4. Disconnect the cooling tube from the blower motor.
  5. Disconnect the electrical connector from the blower motor.
  6. Remove the blower motor mounting bolts.
  7. Remove the blower motor insulating cover.
  8. Remove the blower motor.
To Install:
  1. Install the blower motor.
  2. Install the blower motor mounting bolts.
  3. Connect the electrical connector to the blower motor.
  4. Connect the cooling tube to the blower motor.
  5. Install the rear coolant recovery reservoir mounting stud.
  6. Install the coolant reservoir.
  7. Install the PCM.
W/ Air Conditioning Blower Motor (W/ Air Conditioning) gm-10-00-633.gif

To Remove:
  1. Remove the PCM.
  2. Remove the coolant reservoir.
  3. Remove the rear coolant recovery reservoir mounting stud.
  4. Disconnect the electrical connector from the blower motor.
  5. Move the PCM connectors out of the way.
  6. Remove the blower motor access cover screws. CAUTION
    Do not cut any deeper than necessary in order to remove the access cover.
  7. Cut through the access cover on the cut line using a sharp utility knife.
  8. Disconnect the cooling tube from the blower motor.
  9. Remove the blower motor mounting bolts.
  10. Remove the blower motor.
To Install:
  1. Install the blower motor.
  2. Install the blower motor mounting bolts.
  3. Connect the cooling tube to the blower motor.
  4. Install the blower motor access cover.
  5. Install the blower motor access cover retaining screws.
  6. Using black weather-strip adhesive, seal the cut line.
  7. Connect the blower motor electrical connector.
  8. Reposition the PCM connectors.
  9. Install the rear coolant recovery reservoir mounting stud.
  10. Install the coolant reservoir.
  11. Install the PCM.
prev.gif next.gif

Dec 08, 2010 | 2001 GMC Jimmy

2 Answers

Where is the heater motor


You can get to it from the engine compartment, but you have to cut the cover off. There is an indented line showing where to cut. See picture below.

  1. For the 3.1L engine, remove the alternator belt, then remove the alternator and position aside.
  2. For the 2.5L and 3.3L engines, remove the power steering pressure hose from the power steering pump.
  3. For the 3.0L engine, remove the serpentine belt.
  4. For the 3.0L and 3.3L engines, remove the retaining bolts from the power steering pump bracket, then set the pump aside.
  5. Detach the blower electrical connector, then, if accessible, remove the cooling tube.
When cutting the blower motor cover, make the cut just the thickness of the cover, which is1/ 8 inch (2mm) thick. Cutting deeper than that may damage the cooling tube.

For 1992-98 vehicles, partially cut the blower motor case cover, as shown on the cover. Cutting completely around the cover is NOT required. Swing the cut potion of the cover down.



jturcotte_357.gif

  1. If previously accessible, disconnect the cooling tube.
  2. Unfasten the attaching screws/bolts and remove the blower motor from the case.
  1. If necessary, remove the fan from the blower motor.
  2. The installation is the reverse of the removal procedure.
  3. If the case was cut during removal, secure the cover using the three retaining clips. Tighten the blower motor screws to 44 inch lbs. (5 Nm).
  4. Connect the negative battery cable, then start the engine and check the blower motor for proper operation.

Dec 01, 2010 | 1997 Pontiac Grand Am

1 Answer

Location of the blower motor


from autozone.com: access from engine compartment


REMOVAL & INSTALLATION


See Figures 1, 2 and 3

  1. Disconnect negative battery cable.

7c87335.gif
Fig. 1: Exploded view of the blower motor assembly
  1. For the 3.1L engine, remove the alternator belt, then remove the alternator and position aside.
  2. For the 2.5L and 3.3L engines, remove the power steering pressure hose from the power steering pump.
  3. For the 3.0L engine, remove the serpentine belt.
  4. For the 3.0L and 3.3L engines, remove the retaining bolts from the power steering pump bracket, then set the pump aside.
  5. Detach the blower electrical connector, then, if accessible, remove the cooling tube.

When cutting the blower motor cover, make the cut just the thickness of the cover, which is1/ 8 inch (2mm) thick. Cutting deeper than that may damage the cooling tube.

For 1992-98 vehicles, partially cut the blower motor case cover, as shown on the cover. Cutting completely around the cover is NOT required. Swing the cut potion of the cover down.



973a989.gif Fig. 2: Some later model vehicles require you to cut the case, on the indicated lines, in order to access the blower motor

  1. If previously accessible, disconnect the cooling tube.
  2. Unfasten the attaching screws/bolts and remove the blower motor from the case.

1956a4c.jpg
Fig. 3: On 3.0L engines, you must remove the power steering pump for access to the blower motor
  1. If necessary, remove the fan from the blower motor.
  2. The installation is the reverse of the removal procedure.
  3. If the case was cut during removal, secure the cover using the three retaining clips. Tighten the blower motor screws to 44 inch lbs. (5 Nm).
  4. Connect the negative battery cable, then start the engine and check the blower motor for proper operation.

Sep 22, 2010 | 1997 Pontiac Grand Am

1 Answer

My heater and ac dont work but the blower motor turns on?


REMOVAL PROCEDURE
  1. Remove the right closeout panel.
  2. Remove the blower motor wire harness connector. spacer.gif 2009-08-23_145458_37.thumb.gif spacer.gif spacer.gif View Full Image spacer.gif
  3. Cut out the blower motor using a utility knife in the narrow groove of the lower case. IMPORTANT: Cut through the case as straight as possible because the motor cup must be replaced. In order to prevent damage to the component, do not cut any deeper than necessary to remove the motor cup.
  4. Remove the blower motor
  5. Remove the blower motor nuts. spacer.gif 2009-08-23_145605_38.thumb.gif spacer.gif spacer.gif View Full Image spacer.gif
  6. Remove the blower motor from the blower motor cup.
INSTALLATION PROCEDURE
  • Install the new blower motor to the blower motor cup.
  • Install the blower motor nuts.
  • Install the motor blower seal to the blower motor service ring.
  • Install the blower motor. spacer.gif 2009-08-23_145704_39.thumb.gif spacer.gif spacer.gif View Full Image spacer.gif
  • Install the blower motor attachment ring.
  • Install the blower motor screws.
  • Install the blower motor wire harness connector.
    1. Install the right closeout panel.
  • Apr 15, 2010 | 2001 Chevrolet Impala

    2 Answers

    Heater fan does not work and if I go to #4 on the swich it will blow the 30amp fuse in the fuse box.


    Hello,

    Sounds like you have a short in the system. It sounds like the heater motor might have a short in it.. to check this you will have to take the heater motor out and test it with a battery and some wires.. if it turns the next place to look is the heater resistor. These are located under the hood on the passenger side of the vehicle. You will have to cut an access hole in the plastic cover to access the resistor. These are a pain to get to, and they are pretty common for going bad...

    Good Luck,
    Joe

    Dec 21, 2009 | 1998 GMC Jimmy

    2 Answers

    How do I remove the blower motor on a 2005 Chevy Silverado SS?


    The motor is above the passengers feet.
    Remove the screws then twist it and it will drop out.

    Nov 01, 2009 | 2005 Chevrolet Silverado

    1 Answer

    1992 cadillac that the blower wont turn off


    replace the blower motor speed control module, it is shorted.

    Jul 02, 2009 | Cadillac DeVille Cars & Trucks

    1 Answer

    How to remove a blower motor


    1.) remove screw from right door sill trim plate, (that piece of trim that covers the edge of the carpet when the door is open) 2.) remove right hinge pillar trim panel (passenger side kick panel) 3.) disconnect blower motor electrical connectors 4.) remove blower motor cover 5.) disconnect the cooling tube (rubber hose that attaches to the motor ) .6.) loosen courtesy light screws and move light out of way (if equipped) 7.)remove right side dash support bolt (under dash twist your head around like the excorsist, , lol , where the dash meets the side panel pillar) 8.)remove blower motor-to-case screws 9.) remove blower 10.) remove fan from blower motor shaft 11.) to install reverse removal procedure ,.. not as bad as it sounds , cheers.

    Jan 10, 2009 | 1992 Chevrolet K1500

    Not finding what you are looking for?
    1992 Cadillac Seville Logo

    Related Topics:

    69 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cadillac Experts

    yadayada
    yadayada

    Level 3 Expert

    60867 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6811 Answers

    Are you a Cadillac Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...