Question about Chevrolet C1500

1 Answer

1966 signal light switch

How to replace 1966 chev full size car signal light switch

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 131 Answers

The switch handle either unscrews or unbolts. You must remove your steering wheel first. Once you get it off, you will see the screws that hold it in place. The wires just unplug. Be careful , you will have some springs in there that can pop out when removing the switch.

Posted on Jul 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Left Hand only SIgnal and Brake lights on a 2008 chev 3500 cutaway not working


Turn signal/ multifunction switch. Replace it. All the exterior lights run threw it except the high mount brake light. Check the brake lights. If the high mount works and the others don't . That is a sure sign.

Sep 06, 2016 | Chevrolet 3500 Cars & Trucks

1 Answer

Turn signals 1966 belair


You have a bad ground somewhere. Could be in the harness to the headlite or could be a bonding strap between the engine block and body

Sep 08, 2014 | Cars & Trucks

1 Answer

Brake light and turn signal


check for power at or near socket. Maybe the socket has lost continuity. recommend replacement

Mar 19, 2014 | 1966 Ford Mustang

1 Answer

Drivers side brake light and horn won't work,,is it the multi function switch? 1999 chev blazer 4x4 . if so how much does a new one cost?


No there not connected, replace the brake light
1999 Chevrolet Blazer Auto Light Bulb Size Guide
Low Beam Headlight Bulb Size: 9006
High Beam Headlamp Light Bulb Size: 9005
Parking Light Bulb Size: 3157
Front Turn Signal Light Bulb Size: 3157
Rear Turn Signal Light Bulb Size: 3057
Tail Light Bulb Size: 3057
Stop Light Bulb Size: 3057
High Mount Stop Light Bulb Size: Assembly
Fog/Driving Light Bulb Size: 880 or 881
License Plate Light Bulb Size: 194
Back Up Light Bulb Size: 3156
Front Sidemarker Light Bulb Size: 194
Ash Tray Light Bulb Size: 161
Glove Box Light Bulb Size: 194
Map Light Bulb Size: 168 or 211-2
Step/Courtesy Light Bulb Size: 168 or 211-2
Trunk/Cargo Area Light Bulb Size: 211-2
Under Hood Light Bulb Size: 93
Instrument-General Light Bulb Size: 161 or 37 or PC194 or PC74
Check Engine Indicator Light Bulb Size: PC74
Hi-Beam Indicator Light Bulb Size: PC74
Seat Belt Indicator Light Bulb Size: PC194
Brake Warning Light Bulb Size: PC74
Automatic Transmission Indicator Light Bulb Size: 194
Directional Signal Indicator Light Bulb Size: PC74
As for the horn, inspect the fuse and relay and most common it would be a bad ground wire or worst a bad horn due to corrosion. Horn will be located in the drivers side fender.
Thank you for using fixya.

May 13, 2010 | 1999 Chevrolet Blazer

2 Answers

Left turn signal doesnt work and my brakelights


  1. Check the fuse make sure it is not busted and also use a designated amp only.
  2. Check the bulb and the wires also.

Mar 28, 2010 | 1997 Chevrolet Lumina

1 Answer

Have a 1966 chev impala 4dr Need to change


Disconnect the battery,Then there shoulkd be a bezel ring on the outside of dash facing you hold the switch from the back and break loose bezel ring it will turn counterclockwise as you are looking at it,make sure the new switch matches, transfer wires from old switch to new and reverse proceedure to install.

Aug 25, 2009 | Chevrolet Impala Cars & Trucks

1 Answer

1966 mustang sequential turn/tail/brake lights/signals are ALIVE!


Recheck ALL the wiring, check the brake light switch and signal switch. Either on could have gone bad due to its age. Them suspect the controller for the lights. What do the 4 ways do? I think I would be suspecting the signal switch.

Aug 13, 2009 | 1966 Ford Mustang

1 Answer

1966 chevy turn signal does not work


check the light socket and the wires leading to the socket.The contacts inside are probably nasty looking green or have a white powdery looking corrosion on them,also check to make sure the bulb fits in the socket properly,it could just be worn out.The switch in the column could also have a bad or broken contact,but start with the simple stuff first.

Jun 25, 2009 | Chevrolet Caprice Cars & Trucks

1 Answer

No brake lights and no turn signals on a 1966 mustang, help!


i would check fuses for turn signal if ok check for battery power on both sides of fuse if you have battery power check the turn signal switch in the steering colum the brake lights run through the switch as well

Sep 23, 2008 | 1995 Ford Ranger Supercab

2 Answers

1969 ford mustang mach 1 brake / stop light switch challenge


Most tail light problems are a result of a bad ground......somewhere.

Sep 16, 2008 | 1966 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

68 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...