Question about 1992 Acura Integra Hatchback

1 Answer

Cv joints how much is it to replace each side of a cv joint on a 1992 acura integra.ball park?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Acura Master
  • 2,039 Answers

In canada 2 rebuilt cv 120.00 each 1 hour labour each anywhere 350.00 and up hope it help fixya our problem thanks pierre

Posted on Jul 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Are cv joints hard to replace


Not if you know how, but it takes some effort. The 32mm axle nuts are very tight, it usually needs an impact air gun to get them off. The ball joint is also very tight, and requires specific knowledge to loosen. The axle can be seized in the hub, especially in cars from the north. This can require special tools. Even getting the axle to pop out of the trans can be difficult.

Jun 30, 2014 | 1993 Acura Integra Hatchback

1 Answer

Toyota camry


That usually is a worn CV joint. Go to a smooth surface like a parking lot, wind the windows down, and turn slow circles on full lock. If you hear that noise, it is probably the CV joints and not ball joint noise, since you are not going over bumps.
Also look at the CV rubber boots (2 each side) to find any splits in them. Those let grease out and dirt in, and rapidly end the life of a CV joint.

The individual joints can be replaced, but it isn't worth it. If worn out, get a complete re-manufactured front axle each side.

Jan 28, 2013 | Toyota Camry Cars & Trucks

1 Answer

My lower ball joint broke and axle pop out fixed everything car shakes 30mph on up


sounds like you bent your axle. The smallest bend will put everything off balance. If the axle's not bent, I would say the cv joint is bad. Dam acuras and their ball joints

Jan 19, 2013 | 1993 Acura Legend

1 Answer

How to take off upper control arm on 96 integra


Remove tire, remove lower ball joint, remove cv shaft, remove strut, then remove upper control arm.

Ther is another way to do it but it can be frustrating, You could take tire off , remove the upper bolts in the engine bay and the upper balljoint from the car but the bracket will stay hooked around the strut, There is a thinner metal on the backside of the upper control arm that is removable but requires patience and force, then it will fall into your hands without disconnecting the strut cv shaft or lower ball joint, But you have to remember to reinstall the thin plate before reinstalling the upper ball joint

Oct 19, 2010 | Acura Integra Cars & Trucks

1 Answer

How do u get the drive axle thats broke into two ?


I'm not sure of your question but I think you want to know how do you replace to drive axle also known as the CV joint. To replace the CV joint jack up the side that broke and remove the wheel. Then remove the center nut that holds the CV joint to the hub. Put the car in gear or park so the hub will not turn why you do this or have someone put on the brake why you're doing this. Then remove the lower ball joint. Now pull the hub outward as you push the CV joint in. You may have to do some prying. Now using a pry bar snapped the other side of the CV joint out of the transmission. Reverse this to install new one. Good luck.

Jul 15, 2010 | 1994 Ford Tempo

1 Answer

When making a sharp left turn (like into a driveway or parking space) you can feel & hear a thump. Just had driver's side cv joint replaced, that didn't fix the problem.


This is usually a ball joint. Jack that side up, and just as the wheel starts to clear the pavement, does the bottom slide out a touch? If so, replace you ball joints, and the problem will go away.

Jun 10, 2010 | 1995 Jeep Grand Cherokee

1 Answer

What tools to use to remove front struts on 87 acura integra


1) Jack up the ront part of the car and support it with safety stands.
2) Remove the brake hose clamp bolt.
3)Use floor jack to support the lower control arm. You can place the jack under the ball joint. This is very important. You need to have the jack under the ball joint otherwise force of the torsion bar will jump and cause injury.
4) Remove the self-locking bolt on the knuckle. Slowly lower the jack to remove the strut from the knuckle.
5) Remove two self locking nuts from the upper part of the strut.
) Remove the strut ( front damper) from the car.

May 15, 2010 | 1987 Acura Integra

1 Answer

How do you change a cv joint on a 1992 dodge caravan? The right cv joint is out. Do we need to replace the right axel or can we just change the cv joint?


You need to replace the whole right side axle shaft. Take the ball-joint loose and the axle nut. Pull the shaft from the hub assembly and then pull it from the transmission

Mar 28, 2010 | Dodge Caravan Cars & Trucks

1 Answer

1992 Toyota Corolla CV Joint


You can pick up an entire re manufactured axle assembly at your local auto parts store. In order to replace the assembly you will need to disconnect the tie rod end and the ball joint. Remove the spindle nut. Push the axle stub out of the hub. Now with a suitable container under the axle to catch spilled fluid pry the axle from the transmission housing. Install is the reverse of removal. For more detailed instructions and diagrams go to www.autozone.com vehicle repair guides.

Oct 29, 2009 | 1992 Toyota Corolla

Not finding what you are looking for?
1992 Acura Integra Hatchback Logo

Related Topics:

218 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...