Question about 1996 Nissan Quest

1 Answer

Rear bench seat

How do i remove the rear bench seat?

Posted by on

  • 1 more comment 
  • Anonymous Mar 14, 2014

    the bench seat

  • Anonymous Mar 14, 2014

    plasticroken retaining clips are b

  • Anonymous Mar 14, 2014

    rear bench seat forward

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

The only way to remove this is to unbolt it from the sliding rails. I do believe it would still leave some parts in the rails. This seat was designed to only slide forward and not be removed. If you insist on removing it, then you must unbolt it from the sliding rails...

Posted on Jul 28, 2008

6 Suggested Answers

  • 1 Answer

SOURCE: Seat Removal

Assuming this is a 2001 Chevy Express... standing behind the bench seat you want to remove, you will find an L shaped retaining pin at the left side of each bench seat, down in the floor, toward the rear of the seat posts. There is one for each side and they are color coded, bright blue and yellow. Lift up each of the L shaped retaining pins till they are straight up, push it to the left and remove it. If you've never pulled the seats out, they will be a bit stubborn. Once the pins are removed, either pull the seat towards the back of the van or push it from the front.. whichever gets the seat to move. They fit tight for safety and to avoid rattles. Once the seat moves, usually all at once and quite loudly, lift the seat straight up out of the floor channels. Don't set the seat on your carpet, as they are very heavy and can punch a hole if you put any pressure on it (I did that to mine). Put the colored clips back in place so they don't get lost.

Remember to make sure those seats are firmly in place and correctly latched when you put them back in. Drop them in the slots, push them towards the front of the van firmly. You should not be able to lift them up at this point. Push the pins in hard, they will be tough to push through as they align the seat correctly. You might need to tap those pins in with something heavy to get them to fully seat. Push the pins down into the floor until they latch.

Posted on Sep 23, 2008

  • 2920 Answers

SOURCE: Just got an 2002 Chrysler

i dont think they were meant to fold down but you should be able to take them out to haul bigger items. some of the vans they make are made that way so that you have to remove the seats rather than fold them down

Posted on Dec 06, 2008

  • 132 Answers

SOURCE: I'm trying to remove the rear seat in a 2000

TRY TO PULL IT UP AND OUT MOST CAR's DO NOT HAVE BOLTS FOR THE BACK

Posted on Nov 14, 2009

  • 6 Answers

SOURCE: How do i remove rear bench seat from 08 lancer es

you pull up firmly on the front of the bottom side of the back seat it will pop up, one clip on each side between where your legs would go.

Posted on Dec 25, 2009

  • 3600 Answers

SOURCE: center rear seat does not have a shoulder/lap seat belt

You should be able to go to the dealer and buy the center lap belts and can install them without having to by the seat just call your loacal dealer they can tell you how much thy are, less expensive than the seat.

Posted on Apr 21, 2010

Testimonial: "Thank you avid101. You have provided more information than i was able to get from my dealer and from GM. Neither wished to even address my question."

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Remove rear bench seat


I don't know about your exact make, but every bench rear seat bottom I ever messed with removed as follows:

Get your fingers under the bottom of the seat cushion, and give a sharp tug upwards.
It should be held in by spring clips, which will release with the upward tug.
With the front of the seat cushion slightly raised (so the spring clips can clear the brackets), it should then pull straight forward and out.

To re-install, push the cushion back under the seat back (with the front slightly raised), and with both hands, give a sharp push downwards to latch the spring clips.

Apr 24, 2014 | 1998 Nissan Pathfinder

1 Answer

How do I remove the rear bench seat on a Galant 2010 to install seat covers? Thanks


push back firmly at front of seat at bottomlocating clip released with upward preasure

Nov 14, 2012 | 2010 Mitsubishi Galant

1 Answer

Keys are locked in truck. How do we remove rear seat


I'm going out on a limb here ... is there no remote control access on your key fob? no switch in the glove box ... no opener on the driver side door?

Remove the seat by first pushing the bottom front of the bench part to the rear of the car to unhook the latches, lift it up ... remove the bench. You will then find two bolts ... one on each side of the seat back ... remove them and the seat back should come out ...

Thanks for your interest in FixYa.com

May 01, 2010 | 1999 Oldsmobile Alero

1 Answer

How do I remove the rear seat on a 2001Volvo V70?


I am going to assume you mean the normal rear seats, not rear facing seats in the very back.
The rear seat folds down. The benches fold up from the back. When they are up you can see how to easily remove them if you want.
When the benches are up the backs fold down. There are levers on the top the slide forward to release them so they can be folded down. Tip the outboard head restraints forward by pulling their straps. The center head restraint has a button behind its right-hand support that you push to allow it to be lowered.

Nov 29, 2009 | 2001 Volvo V70

1 Answer

How to remove rear seat in 1996 dodge ram 1500


REMOVAL & INSTALLATION
  1. Clamp the seat belts to keep them from retracting.
  2. Locate and disconnect seat wiring at the connector(s).
  3. Move front seats forward or back for access to the hold down hardware.
  4. Put the rear seats in the stowed position.
  5. On Durango 3rd row seats, lift the cushion upward and forward to floor cargo position.
  6. Remove the hardware securing the seat.
  7. On split bench models, lift the center seat upward to clear attachment stud
  8. Remove the seat from the vehicle.
NOTE Do NOT activate the track adjusters once the fastening hardware is removed.
  1. Installation is the reverse of removal.

336abe0.gif


Fig. Disconnect the wiring from under the seat

36c62e2.gif


Fig. Seat track mounting hardware locations-typical


d95c538.gif

Fig. Bench seat components: seat (1), nut (2), stud (3), floor pan (4), bolt (5)-Ram


1589e1e.gif

Fig. Split bench seat assembly-Ram


616f086.gif

Fig. Bucket seat mounting components-Durango shown


851105e.gif

Fig. Rear seat removal/installation


I hope help you with this; good luck (rated this help).

Aug 31, 2009 | 1996 Dodge Ram 1500 Club Cab

1 Answer

How to remove the back seat from my 1998 Mercury Villager


it is not designed to be removed. It is designed to slide back and forth as needed.

Section 01-10: Seats and Tracks 1998 Villager Workshop Manual
REMOVAL AND INSTALLATION Seat, Rear Bench
Removal
  1. Remove the center seat(s) if equipped. Refer to the procedure in this section.
  1. Slide the bench seat forward to the center row seating position.
  1. Use a flat-blade screwdriver to remove the cover caps from the front of the rear seat cushion latch cover.




  1. Remove the two rear seat bolts from the front of the rear seat cushion latch cover.




  1. Lift the rear seat cushion floor cover on the back of the rear bench seat and remove the two inboard rear seat bolts and the two outboard rear seat bolts.




  1. Remove the bench seat from the vehicle through the body side door opening.

Apr 30, 2009 | 1998 Mercury Villager

2 Answers

I want to make my 1999 Mercury Villager Sport into a cargo loader, with just the front seats kept and the rest of the back empty. How do I remove the other 3 seats? So far, I can't get any of them to budge...


the middle seats come out easily. There are 2 handles you have to lift up on each of the bucket seats, they are in the front of the seat down by the seat tracks. After you lift them, tilt the seat upward in the front and rotate them backward. Then lift out of the hooks. Each seat is held down by 4 hoks.

The 3rd row seat is not designed to come out xcept by a technician. It does slide forward all the way up to the front seat. It has a sliding seat track.
First, lift the T handle under the seat cushion on the left front side of the seat. This will allow you to lift the seat bottom up all the way to lcok in the full up position.
Then, lift the lever on the same side of the seat and slide the seat forward. It will stop in 4 places.
Rear -Rear
6 inches forward of that.
another two ft to the second row seating position
full frward against the front seats.

Pleae rate as fixya if this helps.

c4253aa.gif Seat —Third Row Bench Removal
sxv~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Removal of the third row bench seat requires more than one technician.
  1. Remove the second row seats. For additional information, refer to Seat—Second Row .
  1. Remove the floor mats.
  1. Lock the seat cushion in the upright position.
    1. Lift the handle to release the cushion.
    1. Lock the seat cushion in the upright position.
0235766.gif
  1. Move the third row bench seat to the second row position.
    • Lift the seat track release handle.
  1. Remove the two bolt covers.
  1. Remove the two seat track front bolts.
  1. Remove the four seat track rear bolts.
    1. Position the rear seat cushion floor cover aside.
    1. Remove the four seat track rear bolts.
  1. Remove the third row bench seat.

Mar 02, 2009 | 1997 Mercury Villager

2 Answers

How do i remove rear bench seat from 08 lancer es


Not 100% sure on that particular model but usually you either have a couple of bolts at front of seat down close to floor to remove, one on each side, and if no bolts, you grab front of rear seat, push back on it hard & lift, usually a catch on each side.

Jan 13, 2009 | 2008 Mitsubishi Lancer

Not finding what you are looking for?
1996 Nissan Quest Logo

Related Topics:

404 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...