Question about 2002 Chevrolet Blazer

1 Answer

How do I remove the center floor console?

I need to remove it for a new job with USPS delivering mail. I will be sitting in passenger seat and reaching across with left leg and foot to pedals. The console is in the way. There is no eletrical wires in this console.

Thanks

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 131 Answers

You have one bolt under the rubber mat in the front. And 2 bolts under the arm rest compartment. The plastic compartment in the arm rest will just pull out.

Posted on Jul 12, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you remove the lower center console on a 2000 Olds Intrique


Item Part Number Description 1 060024 Floor console armrest 2 06010 Floor console storage bin 3 04338D Floor console finish panel (front) 4 044D90 Floor console finish panel (center) 5 - Floor console cup holder screws (2 required) 6 13562 Floor console cup holder 7 - Floor console front screws (2 required) 8 - Floor console rear screws (3 required) 9 - Floor console nut 10 045A36 Floor console Removal and Installation
  1. Position the seats as needed to remove the console.
  1. Disconnect the battery. For additional information, refer to Section 414-01 .
  1. Remove the floor console storage bin.
    1. Remove the 3 screws and the armrest.
    1. Remove the floor console storage bin screw.
    1. Remove the pin-type retainer.
    • Disonnect the electrical connectors.
  1. Remove the floor console front finish panel.
    • Pull upward from the front of the trim panel to release the retainers.
    • Disconnect the electrical connectors.
  1. Remove the floor console center finish panel.
  1. If necessary, remove the 2 screws and the floor console cup holder.
  1. Remove the 2 floor console front screws.
  1. Remove the 3 floor console rear screws.
    • To install, tighten to 4 Nm (35 lb-in).
  1. NOTE: Lift the console from the rear and slide it rearward to release the rear seat heater ducts from the instrument panel. Remove the nut and the floor console.
    • Disconnect the electrical connector.
    • To install, tighten to 8 Nm (71 lb-in ).
  1. To install, reverse the removal procedure.

Jun 10, 2015 | 2000 Oldsmobile Intrigue

1 Answer

Need to remove center console to replace seat belt. After removing 12 screws, console is still firmly in place. What else has to be done?


  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest from the floor console.
  2. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  3. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  4. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  5. Lift the floor console from the front and rear console panel mounting brackets.

Feb 27, 2011 | 1996 Ford Explorer

1 Answer

When getting in the passenger side of my 2006 E350, I placed my left knee in the passenger seat to reach over & start car while plugging my laptop in to cigarette adapter in back seat, behind center...


there is a good chance that you will need to take the vehicle in to have the passenger seat resyncronized. The 06 uses a weight sensing system to determine if someone is sitting in the passenger seat. It uses sensors to determine the weight of the occupant by placing your knee in the center it probably thought the sensors weren't reading right since all the weight was in the center of the seat. There is a special set of weights that that dealer has in order to calibrate the sensors again. You might be able to try having someone sit in the passenger seat and then get out a few times and maybe it will see that it's reading correctly now and clear on its own. Laptops running and positioned on the passenger seat have been known to cause problems with this system too at least on the 05's it did.

Dec 01, 2010 | Mercedes-Benz E350 Cars & Trucks

1 Answer

How to Remove Center Console on 1975 GMC Midas RV


If the van has a cup holder on the doghouse you should not have to remove it to get doghouse out. There are 2 latches on the sides of the dog house, one on driver side and one on passenger side about halfway between the floor and the dash, un hook these. Pull the carpet back from around the bottom of the dog house, there will be 2 clips held down with bolts, remove these. The doghouse should slide back, and out from under the dash, it might be necessary to remove the passenger seat to get the house out of the vehicle.

Apr 17, 2010 | GMC Vandura Cars & Trucks

1 Answer

Center console disasembly instructions . we are trying to remove the center console


Base Console, Floor, Ranger, Explorer Removal and Installation
  1. Remove the two oval covers from the sides of the floor console. Remove the four (two on each side) retaining bolts. Lift or remove the front seat center armrest (644A22) from the floor console.
  1. Remove one screw from the top rear end of the floor console (directly under the front seat center armrest.
  1. Remove four screws retaining the utility tray beverage holder to floor console. Lift or remove the utility tray beverage holder from the console.
  1. Remove two screws (directly under the utility tray beverage holder) retaining the front end of the floor console to the console panel front mounting bracket.
  1. Lift the floor console from the front and rear console panel mounting brackets.

c758709.gif

Apr 01, 2010 | 1996 Ford Explorer

2 Answers

2003 cts power seat does not travel forward or back


i have a caddilac cts and my passenger seat does not work anyone has an idea on what it can be?

Nov 20, 2009 | 2003 Cadillac CTS

1 Answer

Where is the fuse box?


It is on the passenger side of the center console, down by the floor. In the general area of where your left ankle would be, if you were sitting in the passenger seat. There is also another one under the hood, on the driver's side. It holds the larger fuses for things like your horn and headlights.

Oct 24, 2009 | 1993 Saturn SL2

1 Answer

1991 camaro... How to remove center console


the best way to do it is take the center console out and the seats so you can properly weld in new floors .. unless your going to just put some tin over them if your going to do this you dont have to remove the console just the seats so you can get the carpet up to place the tin in place..

Apr 19, 2009 | 1991 Chevrolet Camaro

1 Answer

How do you remove or replace the passenger airbag on a 99 contour , Is it a whole dash unit? What holds the drivers bag in the steering wheel? I assumed it was a tork but not sure. Where is the control...


Please rate as fixya if this helps.
the air bag control module is under the console.

  1. Disconnect the battery ground cable.
    1. Wait one minute.
  2. Remove the center console. For additional information, refer to Section 501-12 .
-----------------------------------------------------------------
  1. Disconnect the battery ground cable.
  2. Wait one minute.
  3. NOTE: Contour shown, SVT similar.
    Remove the rear floor console screws.
    1. Move seat fully forward.
  1. Fully apply the parking brake.
  1. Detach the shift indicator selector bezel.
  1. Detach the shift bezel from the selector housing.
    1. Remove three bolts.
    1. Detach shift bezel from the console.
  1. NOTE: The rear floor console must be raised to disengage the front retaining clips.
    Raise and remove the rear floor console.
  1. Remove the four front floor console retaining screws.
  1. Detach the front floor console.
    1. Set the gearshift lever into position 1.
      Partially remove the front floor console.
  1. Disconnect the cigar lighter electrical connections and remove the front center console
-----------------------------------------------------------
  1. Disconnect the air bag control module electrical connectors.
    1. Depress the locking tang.
    1. Slide the locking bar back.
    • Disconnect the connector.
  1. NOTE: The air bag control control module is grounded by the retaining bolts.
    Remove the air bag control module.
    • Remove the three bolts.
--------------------------------------------------------------------------------------------
driver air bag module

  1. Disconnect the battery cables.
  1. Rotate the steering wheel 90 degrees to access and remove the Torx screw. Rotate the steering wheel 180 degrees to access and remove the Torx screws.
  1. Remove the driver air bag module.
    • Disconnect the electrical connector.
    • Remove the air bag module.
------------------------------------------------------------------------------------------
  1. Disconnect the battery cables. For additional information, refer to Section 414-01 .
  1. Open the glove compartment, press the sides inward and lower the glove compartment to the floor.
  1. Remove the passenger air vent duct.
    1. Disconnect the duct from the heater box housing.
    1. Disconnect the duct from the instrument panel register and remove.
29e093f.gif
  1. Disconnect the passenger air bag module electrical connector.
  1. Remove the two retaining bolts securing the rear of the passenger air bag module to the cross-vehicle beam.
14df419.gif
  1. sxp~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Support the passenger air bag module when removing the retaining nuts.
    Remove the two nuts from the front of the passenger air bag module.
4a697c8.gif
  1. Remove the passenger air bag module.
    • Lower the front edge of the passenger air bag module, roll the passenger air bag module around the cross-vehicle beam lowering it into the passenger footwell.
82a0ae0.gif

Mar 15, 2009 | 1999 Ford Contour

Not finding what you are looking for?
2002 Chevrolet Blazer Logo

242 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...